Vossy

Hope for some help. Recently went to reboot my server and I get "db_root: cannot open: /etc/target" and various lines after. I cannot after. I cannot log in to the remote GUI. If in boot in safe mode still get the error but can get the GUI working. I had the error on the screen (I sometimes have a screen connect to my server) for a while. I was running 6.12.0 but everything was working. I tired many times to update from but kept failing. Someone it managed to upgrade to 6.12.4 and ow I have this. Not sure how to work this out. When I boot it normally it does allow SSH in but not sure what to do then. I thought it might the thumb drive so tired a new one using the back up file, but get a different error. "cannot mount bzmodules - press ENTER to reboot...." I have tired different USB ports on he motherboard and no difference A little lost and after some help please. tower-diagnostics-20230924-1721.zip tower-diagnostics-20230924-1621.zip

Thanks all thats exactly what it was. Strange cause the last CPU had it and I didn't change BIOS. Thanks all again

Hello, I recently upgraded my supermicro X8DT6 motherboard with 2 x 5690 Processors. I thought these CPU had 6 cores but 12 threads as below only showing 6 threads for both. What I am missing? tower-diagnostics-20220419-0844.zip

No sure they have BIOS, been running fine for years, now this.... see below LSI Corporation SAS2 Flash Utility Version 20.00.00.00 (2014.09.18) Copyright (c) 2008-2014 LSI Corporation. All rights reserved Adapter Selected is a LSI SAS: SAS2008(B2) Num Ctlr FW Ver NVDATA x86-BIOS PCI Addr ---------------------------------------------------------------------------- 0 SAS2008(B2) 20.00.07.00 14.01.00.08 No Image 00:09:00:00 1 SAS2008(B2) 20.00.07.00 14.01.00.08 No Image 00:08:00:00 2 SAS2008(B2) 20.00.07.00 14.01.00.08 No Image 00:02:00:00 Finished Processing Commands Successfully. Exiting SAS2Flash.

So ran for a few days with not Parity disk, not a single error as soon as I put on in and tired to do a sync errors on 2 x drives (tired a few times different drive each time). Tired with only one parity disk in various locations/slots (I have a NORCO 4224 case, through 3 x LSI card using 6 SAS cables). Still same result. Removed the Parity drives and no read errors. tower-diagnostics-20210307-1111.zip tower-syslog-20210307-0311.zip

I have done a new config a few times but not re-sync, is it worth doing it and re-syncing first before looking else? Or if I have had the failures after a new config it is more than likely a cable, backplane or card issue?

As requested tower-syslog-20210303-2018.zip tower-diagnostics-20210304-0418.zip

Nope now disk 1 and 7 failed again... It seems that is likes two disk failed all the time.... tower-syslog-20210303-1222.zip tower-diagnostics-20210303-2022.zip

Thanks JorgeB vie done that and will let you know.

reboot and all files back but still drives now unmountable .. tower-diagnostics-20210303-1751.zip tower-syslog-20210303-0951.zip

Any ideas, if I clear these two, another different two fail....this time it is 5 and 7...if I had hair id be pulling it out... tower-diagnostics-20210303-1743.zip tower-syslog-20210303-0943.zip

Ill try again.. tower-syslog-20210303-0935.zip tower-diagnostics-20210303-1726.zip

Hello, Not sure what's goings on here. I have been using UNRAID for a few years and going all fine up until a few months ago, lost a drive and when trying to replace found mobo not seeing all ram, further investigation reviled defect mobo. Removed all equipment m(SAS contollers, etc (not RAM or CPU)) used old (Spare) mobo and back up and running all data assessable and present. Showed failures on two drives whilst waiting for new mobo to arrive, ordered replacement disk (was a little shocked as one disk was only 18 months old). Got new board installed and changed out failed disks, started getting random failures on different drives, suspected new Mobo (it was used of EBAY), again no seeing all RAM as well. Put back into old (Spare) and again now seeing random failures of disks. Disks always test out fine in smart tests etc. Using TV show XYZ as example (it has 3 seasons). Now when I browse through windows or plex or unraid UI share it only Season 2 - episode 12, but when I go main and click on another disk and drill down (if it contains that show) it will show some episodes... At a loss any help or advice would be great. tower-diagnostics-20210303-0445.zip

Hello, I recently got 2 errors in my drives (3 and 5). I have downloaded the Diagnoses file. I checked the smart logs, but to be honest not sure what I am looking at? I have carried out a short smart test on both drives and they are ok. tower-diagnostics-20201226-0446.zip

I have just started using Unraid and trying to get nextcloud access using letsencrypt. I have followed spaceinvaderone's tutorial to the letter. I get server ready in my letsencrypt logs. When I try accessing from external using https:// i get This site can’t be reached nextcloud.xxxxxxx.xxx refused to connect. Try: Checking the connection Checking the proxy and the firewall ERR_CONNECTION_REFUSED If I try using http:// I get my modem log in page and can log in and access my modem. Any thoughts?