BinAdhed
-
Posts
12 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Posts posted by BinAdhed
-
-
2 hours ago, JorgeB said:
Do it, may be something there.
syslog attached,
I have an assumption and might be wrong but do I need to retype the command from the release notes after every restart? is that command not permanent? -
On 8/27/2023 at 1:16 PM, JorgeB said:
The call trace mentions the iGPU driver:
Unfortunately, the system decided to freeze today while I was doing a parity sync.
All I did was, stop array, shutdown, insert new HDDs, start server, replace old parity drive with new, start array.
It was going good, and last time I checked it said 13 hours remaining, only to find out later that the server is not responding again.
What should I do in this case?
I think log is still enabled on flash drive, should I attach the file? -
happy to report that the system been up and running with no issues until now.
thanks
-
1
-
-
1 hour ago, JorgeB said:
The call trace mentions the iGPU driver:
Aug 26 16:08:25 UNRAID kernel: DPLL 0 assertion failure (expected on, current off) Aug 26 16:08:25 UNRAID kernel: WARNING: CPU: 9 PID: 13092 at drivers/gpu/drm/i915/display/intel_dpll_mgr.c:191 assert_shared_dpll+0xbe/0xed [i915]Thank you for that.
I ran the command and will report back if it does crash again.-
1
-
-
9 hours ago, JorgeB said:
See the release notes, specifically this part:
https://docs.unraid.net/unraid-os/release-notes/6.12.0#crashes-related-to-i915-driver
Thanks will do and see what happens, may I ask where or how do you know it is an issue related to i915 Driver? I want to learn more about diagnosing / troubleshooting on my own.
Ill report back if any crash happens after doing what is mentioned in the release notes. -
Good day people,
I was running on 6.11 (can't remember which version exactly) I recently decided to change my server chassis from Rosewill RSV-R4000U to RSV-L4412U, for swapping disks if ever needed since I was nearing 2 years of current HDD use, then I thought, new chassis, why not upgrade to Unraid 6.12.3 ?
And so I did some research, tried to look for anything that I have to be aware of, but in the sea of information it was hard to find anything indicative of any failures and everything I read kept indicating that upgrading to 6.12 was a breeze and there will be no issues.
and so I did, and now I regret, first issue was unraid didn't want to boot at all after the upgrade, I kept getting hardware error messages ( that I still get until now - attached below ) at boot, it was very hard to capture, because the moment that screen comes up, it would go blank about one second later and the system would just freeze, I had to long press the power button to get it back, but that happened more than once and I wasn't comfortable doing that so I decided to keep it powered down, and I just removed all disks then went online to try to find out the cause but it was really hard to pin point the issue.
I got a new USB dongle, I restored a backup from unraid connect, and still the same then I read somewhere online that unraid now can run using UEFI so I did try that and viola it doesn't throw a lot of errors and when it gets stuck the screen doesn't go blank or lose signal, then I decided to start in safe mode, and thankfully it did end up booting in safe mode and I can see my settings are intact, I read online to disable plugins and so I did and installed 4 plugins ( Unassigned Devices, CA, Dynamix System Temperature and Unraid Connect) , and then I restarted the server and it booted back normally and I started the array and all was well, until it froze some few hours later.So I decided to do a fresh install and then move the config files back to the new install maybe that would change the outcome or so I thought. I continued reading online anyways and I found something about macvlan vs ipvlan, I tried to find such an option on unraid on how to disable it but couldn't find it, so I just stopped using that one container that used a vlan setting, (And after this post I will remove vlan altogether from the Interface in network settings within unraid), rebooted and the server stayed up for 3 days all good until today when it also decided to freeze.
I have no clue why it does freeze but here is what I already did, I enabled syslog mirroring and I will attach it hopefully something useful would come out of it, I have no clue how to read the syslog, can't understand it even though I tried, I only saw one pattern which doesn't make sense but it kept saying error and throwing the PID to CPU 3, not sure if this is something related or not.
I also attached diagnostics of after the crash.
even though I can ping the server, I cannot enter the GUI, the monitor has no signal so I will restart the server now, I will run a memtest.
The hardware is the same, I only added an HBA (DELL H310 6Gbps SAS HBA FW:P20 9211-8i IT Mode ) to be able to actually use more HDDs.
Also now I am using a PiKVM V3, so I switch from the KVM Screen HDMI to the PiKVM when I leave home for a long period ( like when I did 3 days ago and only came today to find the server frozen although I did use a VM for cloud gaming around 4 hours before the crash )
At the moment the PC specs are as follows
Intel i7 1170032GB DDR4 Ram (Corsair LPX)
Asus H570 Pro Motherboard
RTX 2060 Super (passed through for VMs) with a fake HDMI dongle attached
3 Seagate ironwolf nas hdds as parity and 2 data disks 8TB each
1tb nvme drive passed through for a VM
1tb SSD share
240gb ssd share850W platinum PSU
looking forward for help. and thanks in advance.
-
for anyone facing the same issue, what I did to fix this is to use VLANs.
everything is still the same, I just changed the CCTV from a different subnet to instead have a VLAN tag nothing else and now plex shows the right IP address.thank you everyone for helping
-
On 9/29/2022 at 6:39 PM, jmztaylor said:
My plex container is set to host network. I do not remember if I had a specific reason to do that or not. But it won't hurt to try that. It should at least force it to use the same IP as the unraid server. I am thinking that its just a network config issue.
apologies, I am actually using host not bridge, I probably said that because I tried setting to bridge and the issue didn't resolve, but yeah it is host and that is what made freak out when I was trying to solve this when I saw that even though it's set to host, plex says it is pointing to the other IP.
either way I will virtualize unraid, I think that will make things much easier and cleaner.
Thank you for the reply though I appreciate your time.
-
19 hours ago, jmztaylor said:
What network is plex container using?
bridge network of unraid network on eth0, that is what I set originally and never changed or altered.
But plex on docker page shows port assignment as question marks instead of 32400.
in the web interface it points to the bridge of the other active ethernet port, I'm away from the server at the moment but I think it was eth4.
in the network page I already set eth0 as default.
so I'm still trying to figure out the issue.
Everything works but sometimes the application does not work as expected and is slow to load but from the web everything seems fine even though it points to the wrong bridge
-
I hope this post isn't being ignored.
until now everything is pointing me towards virtualizing unraid and just use it as a NAS and use proxmox for everything else, from my understanding unraid doesn't like working with more than one interface.
-
Good day good people,
I am using unraid version 6.10.3
I have two issues that are annoying, and probably causing me some issues with plex remote access.
Inside plex, in the remote access page, it shows the default host IP of my NIC im using for CCTV (192.168.99.2) the host ip (192.168.52.2) on eth0 (not named eth0 instead br0, in the logs it keeps changing names) which I already set in both plex options in the app itself and within the container settings on docker page, but it still uses the other IP mentioned above so it is causing plex apps outside the network not to connect, only the web based plex works when I access from outside the network.
so the second issue might also be the same as the first, in the logs, and in pfsense I keep seeing logs of shim-br0 trying to hijack eth0 ip, and it goes back and forth every few seconds at times. I am not so sure how to reset these settings without breaking something, I've been using unraid only for one year which is when I started my homelab journey.
I hope that there is nothing that I am missing, I tried to look everywhere, but couldn't find anything in regards to plex issue and default IP of NIC being used as Host for plex container.
Thanks!
Upgraded to 6.12.3 and now I get system freezes
in General Support
Posted
would the macvlan still be an issue even if I don't use vlan at all?
thanks for the answer, yeah i meant the iGPU. so my assumption was wrong.
I will change to ipvlan now and hopefully report back in a week or so of it going with no hiccups.
Thanks Jorge you helped a lot.