Roelfo

Members
  • Content Count

    10
  • Joined

  • Last visited

Community Reputation

1 Neutral

About Roelfo

  • Rank
    Newbie
  1. Will try another usb-stick. I'll let you know how it turns out I don't think the flash is mounted at /boot. See attached photo. I'll try another stick, to check if that is the problem.
  2. I just noticed during boot the following error is displayed: modprobe: FATAL: Module bonding not found in directory /lib/modules/5.10.2 [cant read this part, photo is to blurry. had to take it quickly] id Cannot find device "bond0" I also noted the system time might be off by a few hours (i didn't recognize the time zone displayed). Could that have influence on my network problems? I've had problems in the past with out of sync system clocks and SMB. I'll see if i can change the system time. - Roelof
  3. Hi JorgeB, Thanks for your response. Unfortunately, after running the diagnostics command, no logs folder/files can be found on the usb stick. The command does say "Zip file `/boot/logs/[filename].zip` created". The /mnt folder on the system is empty. Could you point me to the location where the usb drive is usually mounted, so that i can copy the log files over?
  4. Unfortunately, no success. I've also swapped the network cable to see if that helps. Should i be looking at my DHCP settings in the router, or the Unraid settings? I'm not experiencing any problems with any of my other devices (both wired/wireless, static/dynamic IP). I forgot to mention: i also tried changing the network settings manually by editing the config/network.cfg, and i tried using an earlier version of unraid (6.8.3). Both no success
  5. Thanks for the tip! i'll reset my router and report back. I'm running 6.9.2, so the 2,5GbE should not be a problem (although i'm 99% sure i have 1GbE)
  6. I'm trying to do a fresh install of unraid. I'm using the USB Flash Creator. After creating the usb-stick (with static IP settings), and booting, everything goes as expected. Only the ip address displayed is nowhere near the local network ip address (e.g. 169.254.160.118; while my network default gateway is 192.168.2.25). Using the DHCP setting while creating an usb-stick yields similar results. I feel like I'm missing something super obvious, but i cant put my finger on it. Maybe relevant: if booting in GUI mode, the localhost (both localhost and 127.0.0.1) yields a "
  7. Never mind.. my impatience got the better of me. Restarting the array out of the maintenance mode showed it working again! thank you for your help!
  8. Phase 1 - find and verify superblock... Phase 2 - using internal log - zero log... - scan filesystem freespace and inode maps... - found root inode chunk Phase 3 - for each AG... - scan and clear agi unlinked lists... - process known inodes and perform inode discovery... - agno = 0 - agno = 1 - agno = 2 - agno = 3 - process newly discovered inodes... Phase 4 - check for duplicate blocks... - setting up duplicate extent list... - check for inodes claiming duplicate blocks... - agno = 0
  9. Thank you for the quick reply! I'll run it and post an update here.
  10. As stated in the title, one of my data drives cant be mounted: "Unmountable: No file system". The drive worked before. SMART tests (both long and short) complete without issue. SMART logs: tower-smart-20200722-1011.zip xfs_repair -vn output: Phase 1 - find and verify superblock... - block cache size set to 1518952 entries Phase 2 - using internal log - zero log... zero_log: head block 867319 tail block 867260 ALERT: The filesystem has valuable metadata changes in a log which is being ignored because the -n option was used. Expect spurious