Izzy9999

I'll give it a shot. Thanks

I have an LSI 9240-8I flashed to 9211-8i P20 IT mode using Forward breakout cables. Unraid sees the card but not the disks attached to it. There seems to be a problem loading the drivers. I'm running it off of a trial key so none of my drives are attached. Only the 9240 with 2 drives attached to it. Any ideas would be appreciated. Thanks Feb 7 14:38:55 Tower kernel: ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x2f impl SATA mode Feb 7 14:38:55 Tower kernel: ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst Feb 7 14:38:55 Tower kernel: mpt3sas version 26.100.00.00 loaded Feb 7 14:38:55 Tower kernel: mpt3sas 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM control Feb 7 14:38:55 Tower kernel: mpt2sas_cm0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (16383784 kB) Feb 7 14:38:55 Tower kernel: cryptd: max_cpu_qlen set to 1000 Feb 7 14:38:55 Tower kernel: usbcore: registered new interface driver btusb Feb 7 14:38:55 Tower kernel: scsi host3: ahci Feb 7 14:38:55 Tower kernel: usb 1-1.5: Direct firmware load for ar3k/AthrBT_0x01020200.dfu failed with error -2 Feb 7 14:38:55 Tower kernel: scsi host4: ahci Feb 7 14:38:55 Tower kernel: Bluetooth: Patch file not found ar3k/AthrBT_0x01020200.dfu Feb 7 14:38:55 Tower kernel: scsi host5: ahci Feb 7 14:38:55 Tower kernel: Bluetooth: Loading patch file failed Feb 7 14:38:55 Tower kernel: ath3k: probe of 1-1.5:1.0 failed with error -2 Feb 7 14:38:55 Tower kernel: usbcore: registered new interface driver ath3k Feb 7 14:38:55 Tower kernel: AVX version of gcm_enc/dec engaged. Feb 7 14:38:55 Tower kernel: scsi host6: ahci Feb 7 14:38:55 Tower kernel: AES CTR mode by8 optimization enabled Feb 7 14:38:55 Tower kernel: scsi host7: ahci Feb 7 14:38:55 Tower kernel: scsi host8: ahci Feb 7 14:38:55 Tower kernel: ata1: SATA max UDMA/133 abar m2048@0xf7e16000 port 0xf7e16100 irq 28 Feb 7 14:38:55 Tower kernel: ata2: SATA max UDMA/133 abar m2048@0xf7e16000 port 0xf7e16180 irq 28 Feb 7 14:38:55 Tower kernel: ata3: SATA max UDMA/133 abar m2048@0xf7e16000 port 0xf7e16200 irq 28 Feb 7 14:38:55 Tower kernel: ata4: SATA max UDMA/133 abar m2048@0xf7e16000 port 0xf7e16280 irq 28 Feb 7 14:38:55 Tower kernel: ata5: DUMMY Feb 7 14:38:55 Tower kernel: ata6: SATA max UDMA/133 abar m2048@0xf7e16000 port 0xf7e16380 irq 28 Feb 7 14:38:55 Tower kernel: ata3: SATA link down (SStatus 0 SControl 300) Feb 7 14:38:55 Tower kernel: ata1: SATA link down (SStatus 0 SControl 300) Feb 7 14:38:55 Tower kernel: ata6: SATA link down (SStatus 0 SControl 300) Feb 7 14:38:55 Tower kernel: ata2: SATA link down (SStatus 0 SControl 300) Feb 7 14:38:55 Tower kernel: ata4: SATA link down (SStatus 0 SControl 300) Feb 7 14:38:55 Tower kernel: mpt2sas_cm0: sending diag reset !! Feb 7 14:38:55 Tower kernel: mpt2sas_cm0: diag reset: SUCCESS Feb 7 14:38:55 Tower kernel: mpt2sas_cm0: _base_spin_on_doorbell_int: failed due to timeout count(10000), int_status(c0000000)! Feb 7 14:38:55 Tower kernel: mpt2sas_cm0: doorbell handshake int failed (line=5212) Feb 7 14:38:55 Tower kernel: mpt2sas_cm0: _base_get_ioc_facts: handshake failed (r=-14) Feb 7 14:38:55 Tower kernel: mpt2sas_cm0: failure at drivers/scsi/mpt3sas/mpt3sas_scsih.c:10684/_scsih_probe()! syslog.txt

I just installed unRAID and think it's great. The only problem I've encountered is that Windows 10 is reporting the wrong disk size. Yesterday explorer was showing 1.36TB free on a total 9.54TB. I tossed in a spare 1TB drive and now explorer reports 2.11TB free on a total 9.54TB free. It's showing the correct free space but hasn't changed the total space. I'm just in the testing phase but plan to move to larger drives. What will happen when I start to swap out the smaller drives for larger ones? Will I see 20TB free of 9.54TB? How will Windows react to that? Thanks