gzz

I didn't.

Hello. Maybe you can help me. I've trying to replace old HDDs (WD30EZRX) to new Seagate Exos X16 (ST12000NM001G) in NAS WD MyBook Live Duo (APM82181 SoC). One of old HDDs is dead, so i've decided to replace both. If replaced one of two HDDs (WD30EZRX + ST12000NM001G) NAS starting and working successfully. It working also if i've booted in mixed configuration (WD30EZRX + ST12000NM001G) and did a hot switch WD30EZRX to second ST12000NM001G. But with one or two new HDDs (without native WD30EZRX) NAS doesn't start: disks not spinning up. There is no cold start. In UART-console: U-Boot 2009.08-svn54115 (Nov 15 2011 - 10:54:56), Build: 0.0.12 CPU: AMCC PowerPC APM82181 Rev. D at 800 MHz (PLB=200, OPB=100, EBC=100 MHz) Security support Bootstrap Option E - Boot ROM Location NOR/SRAM (8 bits) 32 kB I-Cache 32 kB D-Cache Board: Apollo-3G - APM82181 Board, 2*SATA, 1*USB I2C: ready DRAM: Auto calibration 256 MB FLASH: 512 kB DTT: 1 FAILED INIT Net: PHY EC1 Register: 0x2c8c ppc_4xx_eth0 Type run flash_nfs to mount root filesystem over NFS p=============================================================================q |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::WWWWWWWWW::::WWWWWWW::::::::WWWWWWW::DDDDDDDDDDDDDDDDD::::::::::::| |:::::::::::WWWWWWWW::::WWWWWWWW:::::::WWWWWWW::DDDDDDDDDDDDDDDDDDDD::::::::::| |:::::::::::WWWWWWWW:::WWWWWWWWW::::::WWWWWWW::DDDDDDDDDDDDDDDDDDDDDD:::::::::| |::::::::::::::::::::::::::::::::::::::::::::::::::::::::::DDDDDDDDDDD::::::::| |:::::::::::WWWWWWW:::WWWWWWWWWW::::WWWWWWW::DDDDDDDDD:::::::DDDDDDDDD::::::::| |:::::::::::WWWWWWW::WWWWWWWWWWW:::WWWWWWW::DDDDDDDDD::::::::DDDDDDDDD::::::::| |:::::::::::WWWWWW::WWWWWW::WWWWW:WWWWWWW::DDDDDDDDDD:::::::DDDDDDDDDD::::::::| |:::::::::::WWWWWWWWWWWWW:::WWWWWWWWWWWW::DDDDDDDDDD::::::DDDDDDDDDDD:::::::::| |:::::::::::WWWWWWWWWWWW::::WWWWWWWWWWW::DDDDDDDDDDD:::DDDDDDDDDDDDD::::::::::| |:::::::::::WWWWWWWWWWW:::::WWWWWWWWWW::DDDDDDDDDDDDDDDDDDDDDDDDDD::::::::::::| |:::::::::::WWWWWWWWWW::::::WWWWWWWWW::DDDDDDDDDDDDDDDDDDDDDDDDD::::::::::::::| |:::::::::::WWWWWWWWW:::::::WWWWWWWW::DDDDDDDDDDDDDDDDDDDDDDDD::::::::::::::::| |:::::::::::WWWWWWWW::::::::WWWWWWW::DDDDDDDDDDDDDDDDDDDD:::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| |:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::| b=============================================================================d Hit any key to stop autoboot: 0 USB: OTG-Controller ID(0x4F54) Version(0x290A) Err detect usb time out hostport.d32 0x00001000 0 USB Device(s) found scanning bus for storage devices... 0 Storage Device(s) found ** Block device usb 0 not supported Board is not configured for test. Do normal boot. ----- Checking Boot Partitions ----- SATA DWC initialization 0 init: Waiting for device...............................................................** TimeOUT ** SATA DWC initialization 1 init: Waiting for device...............................................................** TimeOUT ** ** Bad partition 1 ** SATA DWC initialization 0 init: Waiting for device...............................................................** TimeOUT ** SATA DWC initialization 1 init: Waiting for device...............................................................** TimeOUT ** ** Bad partition 1 ** I've read about "3 pin problem" and have cheked voltage in third pin – it is always 0 V. I've sticked up the third pin – no changes. Also i've tryed to switch ST12000NM001G into SATA 1.5 Gb/s legacy mode with setting jumper to two first pins – with no result. I've checked total power: total power for start in mixed configuration is 12 V * 1.48 A = 18 W, PSU gives 36 W. With 400 W of external PSU NAS doesn't spin up HDD too. So, new HDD not spin if not mixed with old HDD. That should try now?