thheller

Can't get the above ~800mbit any higher, but its good enough for now. Tried a couple combinations of buffer sizes/flow control/offload, but nothing seems to make a difference. I'll see if I can figure something out if it goes to ~500 again.

Anything recommended I can check/configure? I'm out of ideas.

Hmm, just tested again on the Unraid system and now I get closer to the Ubuntu speeds. So, I guess its the NIC. iperf3.exe -c 192.168.188.5 -R Connecting to host 192.168.188.5, port 5201 Reverse mode, remote host 192.168.188.5 is sending [ 4] local 192.168.188.3 port 65346 connected to 192.168.188.5 port 5201 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.00 sec 95.8 MBytes 804 Mbits/sec [ 4] 1.00-2.00 sec 96.8 MBytes 812 Mbits/sec [ 4] 2.00-3.00 sec 96.9 MBytes 813 Mbits/sec [ 4] 3.00-4.00 sec 97.1 MBytes 815 Mbits/sec [ 4] 4.00-5.00 sec 97.5 MBytes 818 Mbits/sec [ 4] 5.00-6.00 sec 97.4 MBytes 817 Mbits/sec [ 4] 6.00-7.00 sec 97.6 MBytes 819 Mbits/sec [ 4] 7.00-8.00 sec 97.3 MBytes 816 Mbits/sec [ 4] 8.00-9.00 sec 97.2 MBytes 815 Mbits/sec [ 4] 9.00-10.00 sec 94.3 MBytes 791 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-10.00 sec 970 MBytes 814 Mbits/sec 0 sender [ 4] 0.00-10.00 sec 968 MBytes 812 Mbits/sec receiver Guess thats a good excuse to upgrade to 10GbE

I tested with 3 different client machines, all showing the same behavior. I also ruled out the Switch and Cable, since I swapped the connection between the 2 machines sitting next to each other. From my Windows PC I can get full speed to one machine, but not the Unraid one, regardless of cable/port. I also sort of ruled out the NIC itself, since I just plugged in a ubuntu desktop live usb and booted from that instead of Unraid. With the iperf3 server then running on my Windows machine I still don't get full speed but much closer. Server listening on 5201 ----------------------------------------------------------- Accepted connection from 192.168.188.5, port 40122 [ 5] local 192.168.188.3 port 5201 connected to 192.168.188.5 port 40124 [ ID] Interval Transfer Bandwidth [ 5] 0.00-1.00 sec 112 MBytes 942 Mbits/sec [ 5] 1.00-2.00 sec 112 MBytes 941 Mbits/sec [ 5] 2.00-3.00 sec 112 MBytes 941 Mbits/sec [ 5] 3.00-4.00 sec 112 MBytes 941 Mbits/sec [ 5] 4.00-5.00 sec 112 MBytes 941 Mbits/sec [ 5] 5.00-6.00 sec 112 MBytes 941 Mbits/sec [ 5] 6.00-7.00 sec 112 MBytes 941 Mbits/sec [ 5] 7.00-8.00 sec 112 MBytes 941 Mbits/sec [ 5] 8.00-9.00 sec 112 MBytes 941 Mbits/sec [ 5] 9.00-10.00 sec 112 MBytes 941 Mbits/sec [ 5] 10.00-10.00 sec 0.00 Bytes 0.00 bits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth [ 5] 0.00-10.00 sec 1.10 GBytes 941 Mbits/sec sender [ 5] 0.00-10.00 sec 0.00 Bytes 0.00 bits/sec receiver ----------------------------------------------------------- Server listening on 5201 ----------------------------------------------------------- Accepted connection from 192.168.188.5, port 40126 [ 5] local 192.168.188.3 port 5201 connected to 192.168.188.5 port 40128 [ ID] Interval Transfer Bandwidth [ 5] 0.00-1.00 sec 97.6 MBytes 819 Mbits/sec [ 5] 1.00-2.00 sec 101 MBytes 844 Mbits/sec [ 5] 2.00-3.00 sec 101 MBytes 847 Mbits/sec [ 5] 3.00-4.00 sec 101 MBytes 846 Mbits/sec [ 5] 4.00-5.00 sec 101 MBytes 844 Mbits/sec [ 5] 5.00-6.00 sec 101 MBytes 848 Mbits/sec [ 5] 6.00-7.00 sec 101 MBytes 847 Mbits/sec [ 5] 7.00-8.00 sec 101 MBytes 845 Mbits/sec [ 5] 8.00-9.00 sec 101 MBytes 847 Mbits/sec [ 5] 9.00-10.00 sec 100 MBytes 842 Mbits/sec [ 5] 10.00-10.00 sec 93.3 KBytes 806 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth [ 5] 0.00-10.00 sec 0.00 Bytes 0.00 bits/sec sender [ 5] 0.00-10.00 sec 1005 MBytes 843 Mbits/sec receiver ----------------------------------------------------------- Which only leaves Unraid or its configuration. I did try disabling bonding but that doesn't seem to change anything. Anything else I can try?

I'm only getting half speed when downloading from my new Unraid 6.11.5 Server. Uploading to it gets the full Gbit, but downloading doesn't. This is my first time using Unraid, so I'm not sure where to look. I found the other topics talking about realtek nics, but I have a Intel NIC. Tried a different Port on my Switch and a different Cable. Other PCs on my network get full speeds in both directions between each other, but always only half downloading from Unraid. Tested with iperf3 and openspeedtest running in Docker on the server. # lshw -C network *-network description: Ethernet interface product: Ethernet Connection (2) I219-V vendor: Intel Corporation physical id: 1f.6 bus info: pci@0000:00:1f.6 logical name: eth0 version: 00 serial: 2c:fd:a1:6f:23:4f size: 1Gbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=5.19.17-Unraid duplex=full firmware=0.2-4 latency=0 link=yes multicast=yes port=twisted pair promiscuous=yes speed=1Gbit/s resources: irq:149 memory:f7500000-f751ffff # lspci -v 00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection (2) I219-V Subsystem: ASUSTeK Computer Inc. Ethernet Connection (2) I219-V Flags: bus master, fast devsel, latency 0, IRQ 149, IOMMU group 13 Memory at f7500000 (32-bit, non-prefetchable) [size=128K] Capabilities: [c8] Power Management version 3 Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [e0] PCI Advanced Features Kernel driver in use: e1000e Kernel modules: e1000e iperf3.exe -c 192.168.188.5 -R Connecting to host 192.168.188.5, port 5201 Reverse mode, remote host 192.168.188.5 is sending [ 4] local 192.168.188.3 port 60109 connected to 192.168.188.5 port 5201 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.00 sec 55.8 MBytes 468 Mbits/sec [ 4] 1.00-2.00 sec 55.5 MBytes 465 Mbits/sec [ 4] 2.00-3.00 sec 55.8 MBytes 468 Mbits/sec [ 4] 3.00-4.00 sec 55.8 MBytes 468 Mbits/sec [ 4] 4.00-5.00 sec 55.7 MBytes 467 Mbits/sec [ 4] 5.00-6.00 sec 55.6 MBytes 466 Mbits/sec [ 4] 6.00-7.00 sec 55.8 MBytes 468 Mbits/sec [ 4] 7.00-8.00 sec 56.0 MBytes 469 Mbits/sec [ 4] 8.00-9.00 sec 56.1 MBytes 470 Mbits/sec [ 4] 9.00-10.00 sec 55.1 MBytes 462 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-10.00 sec 559 MBytes 469 Mbits/sec 0 sender [ 4] 0.00-10.00 sec 557 MBytes 467 Mbits/sec receiver iperf3.exe -c 192.168.188.5 Connecting to host 192.168.188.5, port 5201 [ 4] local 192.168.188.3 port 63162 connected to 192.168.188.5 port 5201 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.00 sec 113 MBytes 950 Mbits/sec [ 4] 1.00-2.00 sec 113 MBytes 949 Mbits/sec [ 4] 2.00-3.00 sec 113 MBytes 949 Mbits/sec [ 4] 3.00-4.00 sec 113 MBytes 949 Mbits/sec [ 4] 4.00-5.00 sec 113 MBytes 949 Mbits/sec [ 4] 5.00-6.00 sec 113 MBytes 949 Mbits/sec [ 4] 6.00-7.00 sec 113 MBytes 949 Mbits/sec [ 4] 7.00-8.00 sec 113 MBytes 949 Mbits/sec [ 4] 8.00-9.00 sec 113 MBytes 949 Mbits/sec [ 4] 9.00-10.00 sec 113 MBytes 949 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth [ 4] 0.00-10.00 sec 1.11 GBytes 949 Mbits/sec sender [ 4] 0.00-10.00 sec 1.11 GBytes 949 Mbits/sec receiver