[SOLVED: SMB shares on remote UnRAID server connected to home network via built-in WireGuard tunnel?]

I can’t seem to connect via SMB or NFS to the remote UnRAID server from my home network. 
 

The remote server can ping the home network machines and vise versa. I can also connect to the remote server’s web interface from the home network. 
 

The remote server can also connect via SMB back to the UnRAID server on the home network. 
 

Any thoughts would be appreciated. 
 

ETA: It appears that SMB isn’t listening on the WireGuard interface?

 

 

 

Add to SMB Extra Settings to fix:

[global]
        bind interfaces only = No

[[PLUGIN] IPMI for 6.11+]

On 8/26/2023 at 3:49 AM, JorgeB said:

AFAIK X9 series cannot adjust in steps like X10 or newer.

What do you mean by “steps”?

 

My original server used an X9 board and it adjusted the fans based on CPU temp with the plug-in. I used it through 6.11.5 I believe.

 

I turned off the Fan Control part of the plug-in, set the IPMI to “Optimal”, and the fans are spinning up and down now while the server is performing a parity check. It’s just changing the fan speeds every few seconds rather than the 60 seconds I had the plug-in set to which is kind of annoying when it’s a foot away. 
 

 

https://support.siliconmechanics.com/portal/en/kb/articles/changing-fan-speeds-for-x9-x10-series-boards

[[PLUGIN] IPMI for 6.11+]

I set up a system with a Supermicro X9SRL-F, however, it doesn't appear that this plugin is actually adjusting the fan speeds.

 

Here are some of the log entries where it shows the fan speed should be changing, however, the speeds never change.

 

The fan sensors are all populated in the Readings tab as well.

 

ETA: I also discovered that if I change the Fan Control setting to No, save, and then change it back to Yes it does indeed change the fan speeds...to Full Speed (100%) which I find odd.

 

ETA 2: They system is a completely stock Supermicro CSE-826 chassis.

 

2023-08-25 14:17:43 fan control config file updated, reloading settings
2023-08-25 14:17:43 Fan:Temp, FAN1234(100%):CPU Temp(33°C)
2023-08-25 14:19:20 Stopping Fan Control
2023-08-25 14:19:20 Setting fans to auto
2023-08-25 14:19:50 Starting Fan Control
2023-08-25 14:19:50 Setting fans to full speed
2023-08-25 14:20:00 Fan:Temp, FAN1234(100%):CPU Temp(37°C)
2023-08-25 14:21:52 Stopping Fan Control
2023-08-25 14:21:52 Setting fans to auto
2023-08-25 14:26:54 Starting Fan Control
2023-08-25 14:26:54 Setting fans to full speed
2023-08-25 14:27:05 Fan:Temp, FAN1234(34%):CPU Temp(37°C)
2023-08-25 14:27:35 Fan:Temp, FAN1234(32%):CPU Temp(36°C)
2023-08-25 14:27:45 fan control config file updated, reloading settings
2023-08-25 14:27:45 Fan:Temp, FAN1234(54%):CPU Temp(36°C)
2023-08-25 14:28:15 fan control config file updated, reloading settings
2023-08-25 14:28:15 Fan:Temp, FAN1234(80%):CPU Temp(36°C)
2023-08-25 14:28:45 fan control config file updated, reloading settings
2023-08-25 14:28:45 Fan:Temp, FAN1234(30%):CPU Temp(35°C)
2023-08-25 14:29:15 Fan:Temp, FAN1234(32%):CPU Temp(36°C)
2023-08-25 14:30:45 Fan:Temp, FAN1234(34%):CPU Temp(37°C)
2023-08-25 14:31:15 Fan:Temp, FAN1234(26%):CPU Temp(33°C)
2023-08-25 14:33:15 Fan:Temp, FAN1234(24%):CPU Temp(32°C)
2023-08-25 14:33:45 Fan:Temp, FAN1234(42%):CPU Temp(41°C)
2023-08-25 14:34:15 Fan:Temp, FAN1234(30%):CPU Temp(35°C)

 

 

I'm using this on 4 other Supermicro servers with X10 motherboards  so is this motherboard just too old?  Is there anything that I can do to troubleshoot?

[No SMART data using Mediasonic Probox over eSATA in interface but it's available?]

If I run "smartctl --all /dev/sdh" in the console I get SMART data, however, if I click on the device and then go to Attributes it says "Attributes not available"....thoughts?

[Future Unraid Feature Desires]

Being able to at least add another drive to the array without having to stop it first would be awesome. 

[802.3ad LACP bonding issue]

On 4/2/2021 at 2:25 PM, bkandor said:

Hi, I did do that and was successful getting protocol 4 bonding enabled.  Strangely though, even though it's enabled on both the switch and the unraid box, it isn't functioning the way my qnap or win server bonds are.  i.e. I can never see bond0 throughput go over 1000 mbps - which I can on other devices regularly.  

Did you get this working as I’m having the same issue. It’s using eth0 for receive and eth1 for send on bond0.