It seemed that the only error count changes was the following:
old value:
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 39273
new value:
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 39736
regards,
dl
smartctl version 5.38 [i486-slackware-linux-gnu] Copyright © 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax 16 family
Device Model: Maxtor 4R120L0
Serial Number: R42GVE3E
Firmware Version: RAMB1UU0
User Capacity: 122,942,324,736 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Mon May 10 14:01:59 2010 GMT+8
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 19) The self-test routine was aborted by
the host.
Total time to complete Offline
data collection: ( 182) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 74) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 220 220 063 Pre-fail Always - 8671
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 1214
5 Reallocated_Sector_Ct 0x0033 248 248 063 Pre-fail Always - 57
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 252 238 187 Pre-fail Always - 43654
9 Power_On_Minutes 0x0032 240 240 000 Old_age Always - 448h+41m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 252 252 000 Old_age Always - 457
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 30
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 39736
196 Reallocated_Event_Count 0x0008 252 252 000 Old_age Offline - 1
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 0
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 139 139 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 7 inconsistent with error log pointer 5
ATA Error Count: 7 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 7 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 08 00:04:32.480 READ DMA
c6 00 10 00 00 00 e0 08 00:04:32.480 SET MULTIPLE MODE
91 00 3f 00 00 00 af 08 00:04:32.480 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 08 00:04:32.464 RECALIBRATE [OBS-4]
c8 00 01 00 00 00 e0 04 00:04:32.464 READ DMA
Error 6 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 08 00:04:32.384 READ DMA
c6 00 10 00 00 00 e0 08 00:04:32.384 SET MULTIPLE MODE
91 00 3f 00 00 00 af 08 00:04:32.384 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 08 00:04:32.368 RECALIBRATE [OBS-4]
c8 00 01 00 00 00 e0 04 00:04:32.368 READ DMA
Error 5 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 08 00:04:32.304 READ DMA
c6 00 10 00 00 00 e0 08 00:04:32.304 SET MULTIPLE MODE
91 00 3f 00 00 00 af 08 00:04:32.304 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 08 00:04:32.272 RECALIBRATE [OBS-4]
c8 00 01 00 00 00 e0 04 00:04:32.272 READ DMA
Error 4 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 08 00:04:32.208 READ DMA
c6 00 10 00 00 00 e0 08 00:04:32.208 SET MULTIPLE MODE
91 00 3f 00 00 00 af 08 00:04:32.208 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 08 00:04:32.176 RECALIBRATE [OBS-4]
c8 00 01 00 00 00 e0 04 00:04:32.176 READ DMA
Error 3 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 00 00 00 e0 08 00:04:32.112 READ DMA
c6 00 10 00 00 00 e0 08 00:04:32.112 SET MULTIPLE MODE
91 00 3f 00 00 00 af 08 00:04:32.112 INITIALIZE DEVICE PARAMETERS [OBS-6]
10 00 00 00 00 00 a0 08 00:04:32.096 RECALIBRATE [OBS-4]
e3 00 00 00 aa 00 a0 04 00:04:32.096 IDLE
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Aborted by host 30% 3160 -
# 2 Extended offline Completed without error 00% 3146 -
# 3 Extended offline Completed without error 00% 3129 -
# 4 Extended offline Completed without error 00% 3120 -
# 5 Extended offline Completed without error 00% 3090 -
# 6 Extended offline Completed without error 00% 3071 -
# 7 Extended offline Completed without error 00% 3036 -
# 8 Extended offline Completed without error 00% 3023 -
# 9 Extended offline Completed without error 00% 2986 -
#10 Extended offline Completed without error 00% 2982 -
#11 Extended offline Completed without error 00% 2968 -
#12 Extended offline Completed without error 00% 2953 -
#13 Extended offline Aborted by host 30% 2939 -
#14 Extended offline Aborted by host 20% 2931 -
#15 Extended offline Aborted by host 30% 2915 -
#16 Extended offline Completed without error 00% 2893 -
#17 Extended offline Aborted by host 40% 2890 -
#18 Extended offline Aborted by host 20% 2883 -
#19 Extended offline Completed without error 00% 2864 -
#20 Extended offline Completed without error 00% 2853 -
#21 Extended offline Completed without error 00% 2843 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.