St0r4ge

Thanks! Do I just add the new disc in parity, then add the current parity to the array and select copy? Thank you for your help!

Thank you! I will start the return process with WD. I was also wondering if you could provide advice on the following: I'm replacing the current Parity (8TB) with 2 x 16 TB and adding another 16 TB to the array. I know there are a few ways to do this, but any recommendations? Thank you.

Hi everyone, I'm currently updating my server by adding 3 x 16TB HDD (2 x WD Red Pro, 1 x Ironworlf Pro) and 2 x 1TB SSD (WD Black SN770 for the app data. On Version 6.12.14 Issue 1: My two new NVME SSD (SN770) seem to run hot at around 52 degree under zero load. when I did the preclear, they went to 76 C. Is this normal? seems high. Issue 2: 2 of the 3 HDD work perfectly and completed the preclear. Although I can see the third drive, it won't show the temp and when I do the preclear, it just stays at 0 MB while the time moves. I already switched the SATA cable with another one in the server thinking it might be a bad cable or connection, but nothing changed. everything is the same leading me to believe it's the drive. Here is the log: === START OF INFORMATION SECTION === Model Family: Western Digital Red Pro Device Model: WDC WD161KFGX-68AFPN0 Serial Number: LU WWN Device Id: Firmware Version: 83.00A83 User Capacity: 16,000,900,661,248 bytes [16.0 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5625 ATA Version is: ACS-4 published, ANSI INCITS 529-2018 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Dec 25 12:47:08 2024 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 164 (intermediate level without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Write SCT (Get) Feature Control Command failed: scsi error badly formed scsi parameters Wt Cache Reorder: Unknown (SCT Feature Control command failed) Read SMART Data failed: scsi error badly formed scsi parameters === START OF READ SMART DATA SECTION === SMART Status command failed: scsi error badly formed scsi parameters SMART overall-health self-assessment test result: UNKNOWN! SMART Status, Attributes and Thresholds cannot be read. Read SMART Log Directory failed: scsi error badly formed scsi parameters ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read GP Log Directory failed SMART Extended Comprehensive Error Log (GP Log 0x03) not supported Read SMART Error Log failed: scsi error badly formed scsi parameters SMART Extended Self-test Log (GP Log 0x07) not supported Read SMART Self-test Log failed: scsi error badly formed scsi parameters Selective Self-tests/Logging not supported SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: -3/ 3 Celsius Lifetime Min/Max Temperature: 0/ 0 Celsius Under/Over Temperature Limit Count: 0/0 Minimum supported ERC Time Limit: 70 (7.0 seconds) Write SCT Data Table failed: scsi error badly formed scsi parameters Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: scsi error badly formed scsi parameters SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read SATA Phy Event Counters failed Is my drive DOA? the packaging from WD was quite bad. The last one is more of a question. I'm replacing the current Parity (8TB) with 2 x 16 TB and adding another 16 TB to the array. I know there are a few ways to do this, but any recommendations? Thank you for all your help!