richiecrawdad

I was really hoping for a nice GUI solution, but this one just works better, and I am very new to Unraid so I don't know how to make an app myself yet but the below is working flawlessly, so if you have the Terramaster F4-424 hardware, you may want to disable other fan controllers and give this a try. I hope this helps someone! I tried Dynamix System Autofan with the IT87 driver installed. It worked, except for when my array went to standby mode/spun down: The fan stopped, which is bad in this NAS because it was roasting my NVME storage at 60+ degrees celcius without the fan being on. (With fan on low NVME stays in the 30s). I uninstalled the autofan application and followed the instructions on this page: Controlling Case Fans Based on Hard Drive Temperature – Kevin's Blog Two minor changes i had to make: I had to add 'bash' to this, and, changed to the name of the script: # fan control - every 5 min */5 * * * * /boot/config/scripts/fan_control.sh 2>&1 | /usr/bin/logger -t fan_control So that it looked like this: # fan control - every 5 min */5 * * * * bash /boot/config/scripts/unraid_array_fan.sh 2>&1 | /usr/bin/logger -t fan_control NOTE: When editing /boot/config/go i had to add an '&' at end of the line that was already in there. This allows the command to run in the background and move on to the next line. Ok, I don't know if I really had to do that, but it seemed like a good idea. The script was not working with my nvme drive to detect its temperature, but my AI chat bot helped me put together this improved script for my need. This works with the four hard drive bays in this NAS plus the one NVME I have installed (if you have two NVMEs installed you may want to add that one to the "HD" list in the script). The beauty of this script is that it works flawlessly even when the spinning hard drives are active or on standby, and it doesn't wake them up. It keeps the fan running adequately to control the NVME temperature when the hard drives are hibernating #!/bin/bash # Improved unraid_array_fan.sh ### USER CONFIGURATION ### # List of drives to monitor HD=( /dev/sdb /dev/sdc /dev/sdd /dev/sde /dev/nvme0n1 ) # Fan control settings FAN_OFF_TEMP=25 # °C: fan off at or below FAN_HIGH_TEMP=45 # °C: fan full speed at or above # Fan PWM values (0–255) FAN_OFF_PWM=0 FAN_LOW_PWM=25 FAN_START_PWM=100 FAN_HIGH_PWM=255 # Fan device path ARRAY_FAN="/sys/class/hwmon/hwmon3/pwm3" ### END OF CONFIGURATION ### ### PROGRAM VARIABLES ### HIGHEST_TEMP=0 OUTPUT="" NUM_OF_DRIVES=${#HD[@]} # Linear PWM calculation NUM_STEPS=$((FAN_HIGH_TEMP - FAN_OFF_TEMP - 1)) PWM_INCREMENT=$(( (FAN_HIGH_PWM - FAN_LOW_PWM) / NUM_STEPS )) OUTPUT+="Linear PWM Range: $FAN_LOW_PWM to $FAN_HIGH_PWM in $NUM_STEPS steps of $PWM_INCREMENT\n" ### MAIN LOOP: Get highest drive temperature ### for DEVNAME in "${HD[@]}" do CURRENT_TEMP="" SLEEPING=0 if [[ "$DEVNAME" == *"nvme"* ]]; then # NVMe device CURRENT_TEMP=$(smartctl -A "$DEVNAME" | grep -i 'Temperature:' | head -n1 | awk '{print $2}') else # SATA device SLEEPING=$(hdparm -C "$DEVNAME" | grep -c standby) if [ "$SLEEPING" == "0" ]; then CURRENT_TEMP=$(smartctl -d ata -A "$DEVNAME" | grep -m 1 -i Temperature_Celsius | awk '{print $10}') fi fi # Process valid temperature readings if [ "$SLEEPING" == "0" ] && [ -n "$CURRENT_TEMP" ]; then OUTPUT+=" -- Drive $DEVNAME temp: $CURRENT_TEMP°C\n" if [ "$HIGHEST_TEMP" -lt "$CURRENT_TEMP" ]; then HIGHEST_TEMP=$CURRENT_TEMP fi fi done OUTPUT+="Highest drive temp: $HIGHEST_TEMP°C\n" ### FAN CONTROL ### # Enable fan speed control if needed if [ "$ARRAY_FAN" != "1" ]; then echo 1 > "${ARRAY_FAN}_enable" 2>/dev/null fi PREVIOUS_SPEED=$(cat "$ARRAY_FAN") # Set fan speed based on highest temperature if [ "$HIGHEST_TEMP" -le "$FAN_OFF_TEMP" ]; then echo $FAN_OFF_PWM > "$ARRAY_FAN" OUTPUT+="Setting fan PWM: $FAN_OFF_PWM (OFF)\n" elif [ "$HIGHEST_TEMP" -ge "$FAN_HIGH_TEMP" ]; then echo $FAN_HIGH_PWM > "$ARRAY_FAN" OUTPUT+="Setting fan PWM: $FAN_HIGH_PWM (HIGH)\n" else # Start fan if needed if [ "$PREVIOUS_SPEED" -lt "$FAN_START_PWM" ]; then echo $FAN_START_PWM > "$ARRAY_FAN" sleep 4 fi # Linear PWM between OFF and HIGH FAN_LINEAR_PWM=$(( ((HIGHEST_TEMP - FAN_OFF_TEMP - 1) * PWM_INCREMENT) + FAN_LOW_PWM )) echo $FAN_LINEAR_PWM > "$ARRAY_FAN" OUTPUT+="Setting fan PWM: $FAN_LINEAR_PWM (LINEAR)\n" fi CURRENT_SPEED=$(cat "$ARRAY_FAN") # Output result if [ "$PREVIOUS_SPEED" -ne "$CURRENT_SPEED" ]; then echo "Fan speed changed." echo -e "$OUTPUT" else echo "Fan speed unchanged. Highest temp: $HIGHEST_TEMP°C. Current PWM: $CURRENT_SPEED." fi I placed the above script into /boot/config/scripts/unraid_array_fan.sh. When I used 'sensors-detect' on the command line, this NAS just shows me: ...so all i had to add into the /boot/config/go file was: I downloaded mycrontab.txt and saved it into /boot/config/scripts/mycrontab.txt: # fan control - every 5 min */5 * * * * bash /boot/config/scripts/unraid_array_fan.sh 2>&1 | /usr/bin/logger -t fan_control Then I added the following to /boot/config/go at the bottom: # setup crontab crontab -l > /tmp/file echo '#' >> /tmp/file echo '# Start of Custom crontab entries' >> /tmp/file cat /boot/config/scripts/mycrontab.txt >> /tmp/file echo '# End of Custom crontab entries' >> /tmp/file crontab /tmp/file rm -f /tmp/file I rebooted and monitored the log window in Unraid to confirm it was working every five minutes as expected.