Lesgo

Just checked and the drive is now being reconstructed.

I did check cables and changed ports but the problem still persists.

Here is a copy of the extended SMART test. I am not skilled enough to be able to understand what the conclusion is. smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.19.17-Unraid] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red (SMR) Device Model: WDC WD60EFAX-68JH4N1 Serial Number: WD-WX22DA18RY0A LU WWN Device Id: 5 0014ee 26a132a0f Firmware Version: 83.00A83 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5417 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Jan 7 09:57:19 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13544) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 737) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 233 226 021 - 3350 4 Start_Stop_Count -O--CK 100 100 000 - 175 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 548 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 75 192 Power-Off_Retract_Count -O--CK 200 200 000 - 62 193 Load_Cycle_Count -O--CK 200 200 000 - 343 194 Temperature_Celsius -O---K 125 112 000 - 25 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 294 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 78 Device vendor specific log 0xb9 GPL,SL VS 4 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 10020 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10020 [11] occurred at disk power-on lifetime: 476 hours (19 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:28:52.452 FLUSH CACHE EXT 47 00 00 00 01 00 00 00 00 08 30 a0 08 00:28:52.450 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 30 a0 08 00:28:52.448 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 a0 08 00:28:52.445 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:28:52.445 SET FEATURES [Enable SATA feature] Error 10019 [10] occurred at disk power-on lifetime: 476 hours (19 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:28:52.352 FLUSH CACHE EXT 47 00 00 00 01 00 00 00 00 08 30 a0 08 00:28:52.350 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 30 a0 08 00:28:52.348 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 a0 08 00:28:52.345 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:28:52.345 SET FEATURES [Enable SATA feature] Error 10018 [9] occurred at disk power-on lifetime: 476 hours (19 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:28:52.245 FLUSH CACHE EXT b0 00 d1 00 01 00 00 00 c2 4f 01 00 08 00:28:33.717 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] b0 00 d0 00 01 00 00 00 c2 4f 00 00 08 00:28:33.708 SMART READ DATA ec 00 00 00 01 00 00 00 00 00 00 00 08 00:28:33.701 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 00 08 00:28:33.701 IDENTIFY DEVICE Error 10017 [8] occurred at disk power-on lifetime: 476 hours (19 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 03 00 02 ba a0 f3 c5 e0 00 Device Fault; Error: ABRT 3 sectors at LBA = 0x2baa0f3c5 = 11721044933 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 03 00 02 ba a0 f3 c5 e0 08 00:28:30.085 READ DMA EXT 47 00 00 00 01 00 00 00 00 08 30 a0 08 00:28:30.083 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 30 a0 08 00:28:30.081 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 a0 08 00:28:30.079 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:28:30.078 SET FEATURES [Enable SATA feature] Error 10016 [7] occurred at disk power-on lifetime: 476 hours (19 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 03 00 02 ba a0 f3 c5 e0 00 Device Fault; Error: ABRT 3 sectors at LBA = 0x2baa0f3c5 = 11721044933 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 03 00 02 ba a0 f3 c5 e0 08 00:28:29.984 READ DMA EXT 47 00 00 00 01 00 00 00 00 08 30 a0 08 00:28:29.982 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 30 a0 08 00:28:29.980 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 a0 08 00:28:29.978 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:28:29.978 SET FEATURES [Enable SATA feature] Error 10015 [6] occurred at disk power-on lifetime: 476 hours (19 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 03 00 02 ba a0 f3 c5 e0 00 Device Fault; Error: ABRT 3 sectors at LBA = 0x2baa0f3c5 = 11721044933 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 03 00 02 ba a0 f3 c5 e0 08 00:28:29.885 READ DMA EXT 47 00 00 00 01 00 00 00 00 08 30 a0 08 00:28:29.882 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 30 a0 08 00:28:29.880 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 a0 08 00:28:29.878 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:28:29.878 SET FEATURES [Enable SATA feature] Error 10014 [5] occurred at disk power-on lifetime: 476 hours (19 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 03 00 02 ba a0 f3 c5 e0 00 Device Fault; Error: ABRT 3 sectors at LBA = 0x2baa0f3c5 = 11721044933 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 03 00 02 ba a0 f3 c5 e0 08 00:28:29.784 READ DMA EXT 47 00 00 00 01 00 00 00 00 08 30 a0 08 00:28:29.782 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 30 a0 08 00:28:29.780 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 a0 08 00:28:29.778 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:28:29.778 SET FEATURES [Enable SATA feature] Error 10013 [4] occurred at disk power-on lifetime: 476 hours (19 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 03 00 02 ba a0 f3 c5 e0 00 Device Fault; Error: ABRT 3 sectors at LBA = 0x2baa0f3c5 = 11721044933 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 03 00 02 ba a0 f3 c5 e0 08 00:28:29.686 READ DMA EXT 47 00 00 00 01 00 00 00 00 08 30 a0 08 00:28:29.683 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 30 a0 08 00:28:29.681 READ LOG DMA EXT 47 00 00 00 01 00 00 00 00 00 00 a0 08 00:28:29.679 READ LOG DMA EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:28:29.679 SET FEATURES [Enable SATA feature] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 541 - # 2 Short offline Completed without error 00% 527 - # 3 Short offline Completed without error 00% 484 - # 4 Short offline Completed without error 00% 483 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 24/37 Celsius Lifetime Min/Max Temperature: 19/38 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/65 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (241) Index Estimated Time Temperature Celsius 242 2023-01-07 02:00 27 ******** ... ..( 70 skipped). .. ******** 313 2023-01-07 03:11 27 ******** 314 2023-01-07 03:12 26 ******* ... ..( 5 skipped). .. ******* 320 2023-01-07 03:18 26 ******* 321 2023-01-07 03:19 27 ******** ... ..( 5 skipped). .. ******** 327 2023-01-07 03:25 27 ******** 328 2023-01-07 03:26 26 ******* 329 2023-01-07 03:27 27 ******** 330 2023-01-07 03:28 27 ******** 331 2023-01-07 03:29 26 ******* ... ..( 2 skipped). .. ******* 334 2023-01-07 03:32 26 ******* 335 2023-01-07 03:33 25 ****** ... ..( 8 skipped). .. ****** 344 2023-01-07 03:42 25 ****** 345 2023-01-07 03:43 24 ***** 346 2023-01-07 03:44 25 ****** 347 2023-01-07 03:45 24 ***** ... ..( 79 skipped). .. ***** 427 2023-01-07 05:05 24 ***** 428 2023-01-07 05:06 25 ****** 429 2023-01-07 05:07 24 ***** 430 2023-01-07 05:08 24 ***** 431 2023-01-07 05:09 24 ***** 432 2023-01-07 05:10 25 ****** 433 2023-01-07 05:11 25 ****** 434 2023-01-07 05:12 24 ***** ... ..( 10 skipped). .. ***** 445 2023-01-07 05:23 24 ***** 446 2023-01-07 05:24 25 ****** 447 2023-01-07 05:25 24 ***** 448 2023-01-07 05:26 24 ***** 449 2023-01-07 05:27 24 ***** 450 2023-01-07 05:28 25 ****** 451 2023-01-07 05:29 24 ***** ... ..(128 skipped). .. ***** 102 2023-01-07 07:38 24 ***** 103 2023-01-07 07:39 25 ****** 104 2023-01-07 07:40 24 ***** 105 2023-01-07 07:41 25 ****** 106 2023-01-07 07:42 24 ***** ... ..( 13 skipped). .. ***** 120 2023-01-07 07:56 24 ***** 121 2023-01-07 07:57 25 ****** 122 2023-01-07 07:58 24 ***** ... ..( 10 skipped). .. ***** 133 2023-01-07 08:09 24 ***** 134 2023-01-07 08:10 25 ****** 135 2023-01-07 08:11 24 ***** ... ..( 4 skipped). .. ***** 140 2023-01-07 08:16 24 ***** 141 2023-01-07 08:17 25 ****** ... ..( 2 skipped). .. ****** 144 2023-01-07 08:20 25 ****** 145 2023-01-07 08:21 24 ***** ... ..( 4 skipped). .. ***** 150 2023-01-07 08:26 24 ***** 151 2023-01-07 08:27 25 ****** 152 2023-01-07 08:28 24 ***** 153 2023-01-07 08:29 24 ***** 154 2023-01-07 08:30 25 ****** 155 2023-01-07 08:31 24 ***** 156 2023-01-07 08:32 25 ****** 157 2023-01-07 08:33 24 ***** ... ..( 2 skipped). .. ***** 160 2023-01-07 08:36 24 ***** 161 2023-01-07 08:37 25 ****** 162 2023-01-07 08:38 25 ****** 163 2023-01-07 08:39 24 ***** 164 2023-01-07 08:40 24 ***** 165 2023-01-07 08:41 24 ***** 166 2023-01-07 08:42 25 ****** ... ..( 18 skipped). .. ****** 185 2023-01-07 09:01 25 ****** 186 2023-01-07 09:02 24 ***** 187 2023-01-07 09:03 25 ****** ... ..( 5 skipped). .. ****** 193 2023-01-07 09:09 25 ****** 194 2023-01-07 09:10 24 ***** 195 2023-01-07 09:11 24 ***** 196 2023-01-07 09:12 24 ***** 197 2023-01-07 09:13 25 ****** ... ..( 41 skipped). .. ****** 239 2023-01-07 09:55 25 ****** 240 2023-01-07 09:56 26 ******* 241 2023-01-07 09:57 25 ****** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 75 --- Lifetime Power-On Resets 0x01 0x010 4 548 --- Power-on Hours 0x01 0x018 6 40072568738 --- Logical Sectors Written 0x01 0x020 6 41205015 --- Number of Write Commands 0x01 0x028 6 42061315129 --- Logical Sectors Read 0x01 0x030 6 63086093 --- Number of Read Commands 0x01 0x038 6 1972800000 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 303 --- Spindle Motor Power-on Hours 0x03 0x010 4 235 --- Head Flying Hours 0x03 0x018 4 406 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 62 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 25 --- Current Temperature 0x05 0x010 1 28 --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 38 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x030 1 35 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 65 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 147 --- Number of Hardware Resets 0x06 0x010 4 20 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == 0xff 0x008 7 0 --- Vendor Specific 0xff 0x010 7 0 --- Vendor Specific 0xff 0x018 7 0 --- Vendor Specific |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 73108 Vendor specific WDC_WD60EFAX-68JH4N1_WD-WX22DA18RY0A-20230107-0840.txt WDC_WD60EFAX-68JH4N1_WD-WX22DA18RY0A-20230107-0840.txt

Thank you, will do.

I have a 6TB disk that is showing 187 uncorrectable disk errors as well as 198 uncorrectable sector counts, should it be replaced?