kopuz

I am running the latest version of Unraid with a NetApp ds4243. Few months back I started getting some pretty consistent CRC errors on some drives in the JBOD. I have an extra SAS SFF cable so I decided to swap it to rule out cable failure as the cause of the CRC errors. I powered down both my server and the JBOD and swapped the cables. Didn't see any of the drives in Unraid. I went back to the old cable and still not seeing the drives. I believe I went through every line in the attached logs, but tossing them up just in case I am missing something obvious. Looks like Unraid is still seeing my LSI SAS 2308 RAID Controller still. Attached logs. epicenter-diagnostics-20230806-1531.zip

Replaced 2 of my drives recently that were getting old. I used UD Pre-clear and both replacement drives passed. When replacing the 2nd drive the rebuild completed with no errors but immediately following the device had an error and was disabled by UR. Attached diag file. My apologizes I did reboot the system before downloading the logs. My best course of action? Used to follow a Re-Enable Drive guide but link is no longer working, must be outdated processes. diagnostics-20230404-1425.zip

Ignorance has struck again. Thank you for the education. Removed the interposer and the drive showed up immediately. Initial SMART report passed. If I gave excuses I am sure I would have a dandy of one. Thank you very much.

Thank you for the reply. Need to use the inerposers so I went and tried a number of them. All the same issue. Does Unraid have a requirement for the SMART reports to be readable where Windows doesn't care? Thus the drive working on windows and not in Unraid?

Adding diag zip epicenter-diagnostics-20220814-2313.zip

Hello, Running Unraid with a NetApp ds4246 jbod. The shelf currently has multiple drives working in Unraid. Recently bought a WD 12TB drive that I was able to mount in Windows and appeared to be working as intended. However in Unraid I never see it as a usable drive. Syslog shows Read Capacity fail. Anything else I can check? Just not able to declare the drive DOA since Windows mounted it. Aug 14 22:39:59 EPICENTER kernel: scsi 23:0:25:0: Direct-Access WDC WD1002FBYS-XXXXXXXX PQ: 0 ANSI: 5 Aug 14 22:39:59 EPICENTER kernel: scsi 23:0:25:0: SSP: handle(0x001e), sas_addr(0x5), phy(26), device_name(0x5) Aug 14 22:39:59 EPICENTER kernel: scsi 23:0:25:0: enclosure logical id (0x5), slot(18) Aug 14 22:39:59 EPICENTER kernel: scsi 23:0:25:0: qdepth(254), tagged(1), scsi_level(6), cmd_que(1) Aug 14 22:39:59 EPICENTER kernel: scsi 23:0:25:0: Power-on or device reset occurred Aug 14 22:39:59 EPICENTER kernel: sd 23:0:25:0: Attached scsi generic sg21 type 0 Aug 14 22:39:59 EPICENTER kernel: end_device-23:0:25: add: handle(0x001e), sas_addr(0x500605ba000a8b19) Aug 14 22:39:59 EPICENTER kernel: sd 23:0:25:0: [sdv] Spinning up disk... Aug 14 22:40:17 EPICENTER kernel: .................not responding... Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Read Capacity(16) failed: Result: hostbyte=0x00 driverbyte=0x08 Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Sense Key : 0xb [current] Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] ASC=0x44 ASCQ=0x0 Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Read Capacity(10) failed: Result: hostbyte=0x00 driverbyte=0x08 Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Sense Key : 0xb [current] Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] ASC=0x44 ASCQ=0x0 Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] 0 512-byte logical blocks: (0 B/0 B) Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] 0-byte physical blocks Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Write Protect is off Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Mode Sense: 1f 00 00 08 Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Unit Not Ready Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Sense Key : 0xb [current] Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] ASC=0x44 ASCQ=0x0 Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Read Capacity(16) failed: Result: hostbyte=0x00 driverbyte=0x08 Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Sense Key : 0xb [current] Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] ASC=0x44 ASCQ=0x0 Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Read Capacity(10) failed: Result: hostbyte=0x00 driverbyte=0x08 Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Sense Key : 0xb [current] Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] ASC=0x44 ASCQ=0x0 Aug 14 22:40:17 EPICENTER kernel: sd 23:0:25:0: [sdv] Attached SCSI disk

This community rocks. Thank you for the rapid reply. That drive is getting older and it was in my last chasis that I had a bunch of bad SATA cables in. That was also before which ever version of UNRAID added in monitoring of these state messages. In the end this is good news. Thank you yet again!!

I noticed a drive in my array has a bunch of CRC errors. https://i.imgur.com/CV9nWk7.png I want to acknowledge the errors to reset the count. But I don't see where I can do that anymore... Here is my array from Dashboard. https://i.imgur.com/ry1QhwH.png Is there another place I can reset the error count? Thanks in advance.

Any plans to add a custom set Storage Location?

Thank you for your time on this reply. Going to look into a Gen2 with dual link for drive size. I do plan on using eventually the max drives UNRAID supports in the array as well as a number of SSDs I use for VMs and such.

Hey All, I currently have an Intel S2600CP for my UNRAID build with 15 HHD plus another 6 SSD. Im starting to get some SMART warnings on some of my drives health. I have all of this enclosed in a single 4U Rosewell chassis that is NOT Hot Swapable on the drives and Im terrified of the labor involved in replacing a drive when one eventually fails. I want to upgrade to an external bay for all HHD that is of course hot swapable. Here is where Im seeking that education from the community here. Thank you in advance btw. What is the best way to achieve this? My research has me thinking along the lines of a Xyratex SAS array bay and purchasing an external facing PCIE SAS controller. Would this be supported by UNRAID OS? Looks like I could do this pretty cheap, especially since Gen1 SAS or 3Gbps controller would be plenty fast for my home lab UNRAID needs. Is my research off in anyway so far with what I described? If so would I get more performance at all getting multiple SAS controllers and using multiple PCIe lanes. I also intend to add some more drives if I do build this project so was thinking getting maybe 3 x 12 drive bays and 3 controllers to spread the traffic over 3 lanes. I think with how Im describing my project you pros see my knowledge level with the hardware architecture, so any help suggestion or advise would be greatly appreciated. Some new terrortory for me and exploration isnt very cheap Thanks all!

Yet again thank you sir. Best customer service in the industry I say!

Hey oh, Recently when I update any Docker on my server the dockers go to an orphaned state. I add the docker again and all configuration is in place. I am wondering if this is a permission setting on the docker, but I am not sure what to look for exactly. Thanks in advance!

Just wanted to say thank you again. Working perfectly.

Thank you sir. Digging through your links now.