unknownperson10

ATA Error Count: 16759 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 16759 occurred at disk power-on lifetime: 20069 hours (836 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 02 00 00 00 a0 00 00:29:39.901 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:29:39.900 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 00:29:39.899 SET FEATURES [set transfer mode] ef 10 02 00 00 00 a0 00 00:29:39.899 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:29:39.888 IDENTIFY DEVICE Error 16758 occurred at disk power-on lifetime: 20069 hours (836 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 45 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 03 45 00 00 00 a0 00 00:29:39.899 SET FEATURES [set transfer mode] ef 10 02 00 00 00 a0 00 00:29:39.899 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:29:39.888 IDENTIFY DEVICE ef 10 02 00 00 00 a0 00 00:29:34.240 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:29:34.239 IDENTIFY DEVICE Error 16757 occurred at disk power-on lifetime: 20069 hours (836 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 02 00 00 00 a0 00 00:29:39.899 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:29:39.888 IDENTIFY DEVICE ef 10 02 00 00 00 a0 00 00:29:34.240 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:29:34.239 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 00:29:34.238 SET FEATURES [set transfer mode] Error 16756 occurred at disk power-on lifetime: 20069 hours (836 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 02 00 00 00 a0 00 00:29:34.240 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:29:34.239 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 00:29:34.238 SET FEATURES [set transfer mode] ef 10 02 00 00 00 a0 00 00:29:34.238 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:29:34.232 IDENTIFY DEVICE Error 16755 occurred at disk power-on lifetime: 20069 hours (836 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 45 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 03 45 00 00 00 a0 00 00:29:34.238 SET FEATURES [set transfer mode] ef 10 02 00 00 00 a0 00 00:29:34.238 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:29:34.232 IDENTIFY DEVICE ef 10 02 00 00 00 a0 00 00:29:28.580 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 00 00:29:28.577 IDENTIFY DEVICE

Can someone please interpret this for me hDD apparently defective but smart test passed ? 1 Raw Read Error Rate 0x002f 199 198 051 Pre-fail Always - 16670 3 Spin Up Time 0x0027 190 184 021 Pre-fail Always - 6491 4 Start Stop Count 0x0032 085 085 000 Old age Always - 15612 5 Reallocated Sector Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek Error Rate 0x002e 009 009 000 Old age Always - 8898 9 Power On Hours 0x0032 073 073 000 Old age Always - 20077 10 Spin Retry Count 0x0032 100 100 000 Old age Always - 0 11 Calibration Retry Count 0x0032 100 100 000 Old age Always - 0 12 Power Cycle Count 0x0032 099 099 000 Old age Always - 1426 192 Power-Off Retract Count 0x0032 200 200 000 Old age Always - 32 193 Load Cycle Count 0x0032 184 184 000 Old age Always - 48024 194 Temperature Celsius 0x0022 111 096 000 Old age Always - 36 196 Reallocated Event Count 0x0032 200 200 000 Old age Always - 0 197 Current Pending Sector 0x0032 200 200 000 Old age Always - 0 198 Offline Uncorrectable 0x0030 200 200 000 Old age Offline - 0 199 UDMA CRC Error Count 0x0032 200 200 000 Old age Always - 0 200 Multi Zone Error Rate 0x0008 197 197 000 Old age Offline - 750 Capabilities Feature Value Information Offline data collection status: 0x82 Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: 0 The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: 21600 seconds. Offline data collection capabilities: 0x7b SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: 0x0003 Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: 0x01 Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: 2 minutes. Extended self-test routine recommended polling time: 248 minutes. Conveyance self-test routine recommended polling time: 5 minutes. SCT capabilities: 0x3037 SCT Status supported. SCT Feature Control supported. SCT Data Table supported. Identity Title Information Model Family: Western Digital Caviar Green Device Model: WDC WD10EADS-00P6B0 Serial Number: WD-WCAV5S594737 LU WWN Device Id: 5 0014ee 2b06e5ed5 Firmware Version: 01.00A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device: In smartctl database [for details use: -P show] ATA Version: ATA8-ACS (minor revision not indicated) SATA Version: SATA 2.6, 3.0 Gb/s Local Time: Sun Jul 19 10:24:42 2015 EDT SMART support: Available - device has SMART capability. SMART support: Enabled SMART overall-health: Passed