zekemdm
-
Posts
42 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Posts posted by zekemdm
-
-
Thank you. Next time it occurs I will try this. For now I re-installed the RealTek NIC and it is working again.
-
I tried removing the binding of the IOMMU groups for the nic to enable the vm manager and unassigned the interfaces for pfsense, but with the 4 ports of the nic unbinded the onboard ethernet again went dark when I enabled the vm manager on unraid.
-
When I start unRAID VM service the onboard Ethernet goes dead.
I run pfSense on my unRAID server using a 4 port 1gb nic. I had a Realtek nic but it would become unresponsive so I swapped it out with an Intel I350 4 port nic. Now I can’t start the VM service running pfSense.
I believe it has to do with pfsense set to auto start and the current interface assignments not matching the hardware now. Previously I changed the assignments in the console but now I can’t get that far.
Could it be that my z590 motherboard onboard Ethernet is Realtek 2.5Gbe and the NIC is Intel I350 1Gbe? Brand compatibility issue?
-
The docker image was filling up again, so I made changes to the extra parameters in the Plex container and it seems to have resolved my issue. This is the video on how to make those changes.
-
I changed the Plex container Host Path 2 to /tmp (host) /transcode (container). So far, I haven't seen the problem of high disk utilization on docker.img reoccur.
-
Hello,
I am troubleshooting the increasing size of my docker.img, I believe it to be Plex. In the course of that, I found this error and a forum post that I should create a post here. Please find the attached diagnostics.
Thank you.
-
I have recurring issues with one of my drives and have swapped out drives, cables and switched SATA ports (I believe, it's been a while). Now I would like to permanently remove the drive from use. How do I shrink my array by the one drive and restore parity to the array. Currently the drive in question is unselected and shows as not installed. I have completed a read-check but the array says unprotected. When I reassign the drive to the array and it attempts to emulate, it will receive an error very shortly into the emulation process. Looking at the drive, it shows 2 GB used of 2 TB. The file viewer shows no files on the drive, I am willing to risk losing some data that might be on there to resolve this issue. Can I achieve parity with the loss of the drive and not replacing it? How can I do that? Thank you.
-
I have UD 2022.06.10 and am trying to install 2022.07.04. I am receiving 502 bad gateway when I attempt to update or remove. I believe it is inhibiting me from other actions like creating a user, starting a parity check, and creating new shares. I am on unRAID version 6.10.3.
-
I have UD 2022.06.10 and am trying to install 2022.07.04. I am receiving 502 bad gateway when I attempt to update or remove. I believe it is inhibiting me from other actions like creating a user, starting a parity check, and creating new shares. I am on unRAID version 6.10.3.
-
Thanks for your reply.
-
Hello, my disk 11 is disabled while conducting the parity check at the beginning of the month. This is the second time since August this has happened. Both times has been disk 11. I have replaced the drive, even though it was a new drive. I also replaced the SATA cable and used another SATA port on the motherboard. At this point I am looking to remove the drive all together and shrink my array size. I have pulled a diagnostics package and attached it here. Any ideas to what could be the cause are much appreciated and as to possibly retrieving the data (2.03GB) that is on the drive if I shrink the array by removing the drive. Thank you.
-
Hello,
I cannot select the host Sound Card (Intel Cannon Lake PCH cAVS (00:1f.3)) and start any VM without receiving the following error:
Execution error: internal error: qemu unexpectedly closed the monitor: 2020-06-16T12:05:23.504317Z qemu-system-x86_64: -device vfio-pci,host=0000:00:1f.3,id=hostdev0,bus=pci.8,addr=0x1: vfio 0000:00:1f.3: group 13 is not viable Please ensure all devices within the iommu_group are bound to their vfio bus driver.
Here is my IOMMU group 13:
IOMMU group 13: [8086:a309] 00:1f.0 ISA bridge: Intel Corporation Cannon Point-LP LPC Controller (rev 10)
[8086:a348] 00:1f.3 Audio device: Intel Corporation Cannon Lake PCH cAVS (rev 10)
[8086:a323] 00:1f.4 SMBus: Intel Corporation Cannon Lake PCH SMBus Controller (rev 10)
[8086:a324] 00:1f.5 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH SPI Controller (rev 10)
[8086:15bb] 00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection (7) I219-LM (rev 10)I looked through the forum and saw similar but not the same errors. Is there a work around for this issue?
I tried the xml sound card edit for my Windows Server 2016 VM as shown by spaceinvaderone Windows 10 VM YouTube video, but it did not work either.
Thank you.
-
Thank you. Luckily it did not write to the MBR of the disks and fortunately I was able to get the original build up and running. I replaced the parity disk since it kept overheating. It is doing a rebuild now, I think I am good now.
-
Hello,
I built an unRAID system with 16 drives, the power supply failed and I have been unable to obtain an identical motherboard.
I purchased a PowerEdge R510 and tried to configure all of the drives (14 total) as RAID 0 (I did not initialize the disks) and restore the system. Only the cache disk took. When I assigned the drives, they say wrong instead of missing.
I am looking at three options;
1. Is there a way I can configure the H700 RAID controller so that unRAID recognizes the disks? In the RAID controller settings I built RAID 0 drives for each and named them (limited character input) how they were labeled in unRAID.
2. Can I save my current configuration, start new unRAID build on the PE R510 with the possibility of restoring my previous unRAID build if I can get another computer built?
3. Can I extract any of the data from the current unRAID build drives outside of a working unRAID array. There are photos and videos, the photos are either in apple photos database or Lightroom database.
Thank you.
Downloads using binhex-delugevpn makes pfSense and internet unresponsive only restores by rebooting unraid
in General Support
Posted
I have a four port nic on my server. I run a pfSense VM that is my router and I run a docker container binhex-delugevpn. I only use deluge to download files, I do not use it for my server traffic or any other traffic. When I have a download in progress before the download completes, the transfer will die down slowly, then I will lose internet. I can access the terminal for pfSense, but the GUI is non-responsive. I reboot my unRAID and that solves the problem. There is nothing new/recently changed in my setup that I know of. I'm interested in ideas as to what the problem could be so I can further troubleshoot.
oberon-diagnostics-20230606-2143.zip