zekemdm

I have a four port nic on my server. I run a pfSense VM that is my router and I run a docker container binhex-delugevpn. I only use deluge to download files, I do not use it for my server traffic or any other traffic. When I have a download in progress before the download completes, the transfer will die down slowly, then I will lose internet. I can access the terminal for pfSense, but the GUI is non-responsive. I reboot my unRAID and that solves the problem. There is nothing new/recently changed in my setup that I know of. I'm interested in ideas as to what the problem could be so I can further troubleshoot. oberon-diagnostics-20230606-2143.zip

Thank you. Next time it occurs I will try this. For now I re-installed the RealTek NIC and it is working again.

I tried removing the binding of the IOMMU groups for the nic to enable the vm manager and unassigned the interfaces for pfsense, but with the 4 ports of the nic unbinded the onboard ethernet again went dark when I enabled the vm manager on unraid.

When I start unRAID VM service the onboard Ethernet goes dead. I run pfSense on my unRAID server using a 4 port 1gb nic. I had a Realtek nic but it would become unresponsive so I swapped it out with an Intel I350 4 port nic. Now I can’t start the VM service running pfSense. I believe it has to do with pfsense set to auto start and the current interface assignments not matching the hardware now. Previously I changed the assignments in the console but now I can’t get that far. Could it be that my z590 motherboard onboard Ethernet is Realtek 2.5Gbe and the NIC is Intel I350 1Gbe? Brand compatibility issue? oberon-diagnostics-20230507-0954.zip

The docker image was filling up again, so I made changes to the extra parameters in the Plex container and it seems to have resolved my issue. This is the video on how to make those changes.

I changed the Plex container Host Path 2 to /tmp (host) /transcode (container). So far, I haven't seen the problem of high disk utilization on docker.img reoccur.

Hello, I am troubleshooting the increasing size of my docker.img, I believe it to be Plex. In the course of that, I found this error and a forum post that I should create a post here. Please find the attached diagnostics. Thank you. nas-diagnostics-20230130-0648.zip

I have recurring issues with one of my drives and have swapped out drives, cables and switched SATA ports (I believe, it's been a while). Now I would like to permanently remove the drive from use. How do I shrink my array by the one drive and restore parity to the array. Currently the drive in question is unselected and shows as not installed. I have completed a read-check but the array says unprotected. When I reassign the drive to the array and it attempts to emulate, it will receive an error very shortly into the emulation process. Looking at the drive, it shows 2 GB used of 2 TB. The file viewer shows no files on the drive, I am willing to risk losing some data that might be on there to resolve this issue. Can I achieve parity with the loss of the drive and not replacing it? How can I do that? Thank you. nas-diagnostics-20220714-0721.zip

I have UD 2022.06.10 and am trying to install 2022.07.04. I am receiving 502 bad gateway when I attempt to update or remove. I believe it is inhibiting me from other actions like creating a user, starting a parity check, and creating new shares. I am on unRAID version 6.10.3. nas-diagnostics-20220709-0106.zip

I have UD 2022.06.10 and am trying to install 2022.07.04. I am receiving 502 bad gateway when I attempt to update or remove. I believe it is inhibiting me from other actions like creating a user, starting a parity check, and creating new shares. I am on unRAID version 6.10.3. nas-diagnostics-20220709-0106.zip

Thanks for your reply.

Hello, my disk 11 is disabled while conducting the parity check at the beginning of the month. This is the second time since August this has happened. Both times has been disk 11. I have replaced the drive, even though it was a new drive. I also replaced the SATA cable and used another SATA port on the motherboard. At this point I am looking to remove the drive all together and shrink my array size. I have pulled a diagnostics package and attached it here. Any ideas to what could be the cause are much appreciated and as to possibly retrieving the data (2.03GB) that is on the drive if I shrink the array by removing the drive. Thank you. nas-diagnostics-20211126-1448.zip