dpackham

Are there logs that we can see that would show some of these failures? i cant find one

Same here. I get a 404, and Nvidia isn't working. GT1030 card. 580 drivers. I do see it +-----------------------------------------------------------------------------------------+ | NVIDIA-SMI 580.159.03 Driver Version: 580.159.03 CUDA Version: 13.0 | +-----------------------------------------+------------------------+----------------------+ | GPU Name Persistence-M | Bus-Id Disp.A | Volatile Uncorr. ECC | | Fan Temp Perf Pwr:Usage/Cap | Memory-Usage | GPU-Util Compute M. | | | | MIG M. | |=========================================+========================+======================| | 0 NVIDIA GeForce GT 1030 Off | 00000000:01:00.0 Off | N/A | | 50% 29C P8 N/A / 19W | 3MiB / 4096MiB | 0% Default | | | | N/A |

The persistent syslog? Do I need to enable syslog mirror to flash for that?

OK right. I'll keep working on getting something logged

I can do that to get going again, but that's no fun :). Anything else I can look at? Would I have to move all my shares over to single disks as well?

The/mnt/disk1 2 and 3 shares all work fine after/mnt/user has failed. my appdata is on FUSE at /mnt/user/appdata

reading this thread. sounds exactly like whats happening to me

Seems to be a SHFS issue. is there a way to turn on logging?

OK it ran for a bit this time and i was able to install some dockers. then it hung again. around 10:45 MST. ish as I dont really know when it failed All_2025-11-4-10_55_48.csv

BTW to reboot it via SSH i need to rename the /usr/local/sbin/diagnostic link to that it wont run as it hangs indefinitly and never finishes and therefore needs to ne kill -9 'd

it should. i downloaded it from the synology after i could not CD to /mnt/user anymore. but not sure time when it went away.

OK, did that and rebooted. And attached are the syslogs that were sent to my Synology backup Some more info is that I can use the unraid shell and cd /mnt/disk1 and disk2 and disk3 just fine and run something like du -s etc., all works. When I try to cd to /mnt/user, it hangs. All_2025-11-4-9_23_23.csv

I cant get the diagnostics after it happens, as the disk process hangs trying to get "df" info, etc, due to the missing /mnt/user mounts. i can try too setup a remote syslog server if that will help?

Here is the backstory. I have been running this server for a year+ + now and DID have similar issues with this unmounting/hanging of the "unioned" filesystems mounted below /mnt/user/. The "user" mount point dies after N minutes. So back then, I uninstalled the SAS sleep plugin and let the SAS drives never sleep. it fixed it until last week. I ran the 7.2 RC builds with NO problem, then when I installed the 7.2 release, it started happening again. Here is what I have done to troubleshoot Run in Safe Mode. Still hung. Rebuilt my USB boot drive with serial and NO plugins and NO Docker. Runs fine. Although the UI for drive parity checking, due to multiple reboots, does not update as it used to. I have waited until the check is complete and Docker is enabled, and it still hangs. I ordered a NEW SAS card from the list of supported ones in the forums, but there's still no real change. If I keep Docker disabled, it works, but I need Docker. I WAS using a Docker file with plenty of free space and have moved it between drives to check that. I have checked the SMART data on the drives and see a few read and write errors, but they didn't look too bad. Not sure where to go from here. I thought that a total rebuild of the OS work had been done. But it has not. Ideas? Anything you can see in the diag zip? dmesg and syslog didnt show me anything that i can recognize. unraid-diagnostics-20251103-0649.zip

OK. It's been stable now for almost a week without the SAS spindown plugin... ill post something in the plugin support thread as I would like it to work. Thanks all

Okay, it's been up for two days now. Not spinning down anymore, but it's stable so far. I'll reach back out in a week if all is good and sooner if not. Thanks all

I have unloaded the SAS sleep plugin. Rebuilding parity now. . lets see when they try to go to sleep again if they do

Attached to this thread

Here are the syslogs for the past few days. it happened again last night All_2025-4-13-8_28_25.csv.zip

That is true. I have eight spare SAS drives that all click when put in, so I'm thinking it's not the disk. I will double-check the power and cables, but right now, it's running, and I'm doing backups. .

When it's been running for a while, it's just lost the disk, and the web UI is hung. I can get into the console and try a reboot, but that hangs on gathering diag data. I'm assuming that its lost both as SMB and NFS share are also dead

I have had this system running with some new SAS drives in an external case connected to the SAS controller inside the CPU for a few months now. When I start the external SAS enclosure, the drive doesn't make any sound. When I boot the CPU and it gets to the SAS bios, the drive starts clicking every 5 seconds, and unraid doesn't see the drives. Sometimes, if I wait long enough, the drives in the external array will spin up, and then the SAS bios finds them. Once it's up and running, everything is fine for a few days, and then we get the clicks again. Am I having problems with the external enclosure? Diag logs attached unraid-diagnostics-20250411-0909.zip

Working great now.

That worked. package installed. time to finish config and test

I think I got it. another plugin installed the x86 version of zip. this is fixed now. installing RSA now