willis
-
Posts
16 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Posts posted by willis
-
-
I would run a SMART extended self test on the suspect drive.
thats already running but the short test also took a while, will post it when ready
-
Here is the SMART Report for the disk, i just received word from Seagate that the disk that i already send was indeed broken en they just send me a new one.
Here is the smart data for the disk (2of2) that i didn't send to seagate (will do it if it fails again).
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.4.30-unRAID] (local build)
Copyright © 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Archive HDD
Device Model: ST8000AS0002-1NA17Z
Serial Number: Z840PHNF
LU WWN Device Id: 5 000c50 0925478dd
Firmware Version: AR17
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5980 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Dec 2 12:57:26 2016 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 945) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x30b5) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 153884704
3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 15
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 4452444632
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 977
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 15
183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 061 052 045 Old_age Always - 39 (Min/Max 21/43)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 266
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 400
194 Temperature_Celsius 0x0022 039 048 000 Old_age Always - 39 (0 21 0 0 0)
195 Hardware_ECC_Recovered 0x001a 117 099 000 Old_age Always - 153884704
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 932 (48 171 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 109234797504
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 198835488429
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 975 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
If de disk fails again, i will post the errors i receive maybe that explains it a little bit better.
-
Disk was disabled and many sector errors. Same happening sector errors so the drive was disabled.
I'd put money on there being nothing at all wrong with either disk, and it's actually a bad SATA cable or power cable.
That was what i was thinking, but i replaced the Sata cables (also the complete psu (now have a corsair 550) and also (after that didn't work) changed from the sata controller to the onboard sata controller. both the same result (disabled disk after sector errors).
Did you replace the SATA cable with a high-quality locking cable? Also, with 9 disks 550w SHOULD be enough, but is this one of Corsair's better power supplies or the low-end CX series? If your 3rd disk has this same issue, I'd replace the power supply with a higher quality unit that also has a bit more capacity (650w would be PLENTY).
Meanwhile, I have to agree with your earlier conclusion ...
... So you can say my luck with these disks is not joyfull at this moment...
The Corsair is a RMX550, the one with the modulair cables.
I didn't replace it with a high quality cable, i have a set of sata cables (same for all the other disks)
I don't have any smart status at this moment because i wanted to get a new disk asap, however i had an error in the log. That error i googled (i don't have the error available to me right now) that suggested that the disk was really broken.
-
Disk was disabled and many sector errors. Same happening sector errors so the drive was disabled.
I'd put money on there being nothing at all wrong with either disk, and it's actually a bad SATA cable or power cable.
That was what i was thinking, but i replaced the Sata cables (also the complete psu (now have a corsair 550) and also (after that didn't work) changed from the sata controller to the onboard sata controller. both the same result (disabled disk after sector errors).
-
So i have 4 of these disks in my setup (4x 8TB Seagate ST8000AS0002) 2x 8TB WD Red disks and 3x 4TB (seagate and wd).
But from the first week of my Build (now 2 months old) there were some problems with disk1 in my Array (the 8TB Seagate disk).
Disk was disabled and many sector errors. So i RMA'd the disk and ordered a new one (was on my wishlist) and replaced the broken disk with the new ordered disk. All was well for a couple of days, and then Disk1 was broken again, remember that this was the replaced new disk). Same happening sector errors so the drive was disabled. Re-added the disk and parity was calculated an restored the disk.
Offcourse the problem was returning after a few days. So the status this moment is, send that broken disk to Seagate, ordered a 8TB WD disk to replace it. the replaced Seagate disk will be added later.
So you can say my luck with these disks is not joyfull at this moment...
Seagate 8TB Shingled Drives in UnRAID
in Storage Devices and Controllers
Posted
And here is the output of the Extended test, still everything is ok at this moment. the new WD Disk does its job well.
smartctl 6.5 2016-05-07 r4318 [x86_64-linux-4.4.30-unRAID] (local build)
Copyright © 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Archive HDD
Device Model: ST8000AS0002-1NA17Z
Serial Number: Z840PHNF
LU WWN Device Id: 5 000c50 0925478dd
Firmware Version: AR17
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5980 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Dec 3 19:26:46 2016 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 945) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x30b5) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 118 099 006 Pre-fail Always - 198727088
3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 15
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 4460112493
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1007
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 15
183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 061 052 045 Old_age Always - 39 (Min/Max 21/43)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 268
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 402
194 Temperature_Celsius 0x0022 039 048 000 Old_age Always - 39 (0 21 0 0 0)
195 Hardware_ECC_Recovered 0x001a 118 099 000 Old_age Always - 198727088
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 962 (18 143 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 112011471096
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 199789103661
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 1005 -
# 2 Short offline Completed without error 00% 975 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.