smakdafrog

January 4, 2021

I don't see anything resembling a 7 hour pattern, but I'd have to leave the server on for a bit longer to make sure (rebooted after previously posting). I believe my issues stem from Cache Dirs, I'm not sure why. All of my disks of XFS, and this problem seemed to have cropped out of no where over the past month or so. I disable cache dirs and the process calls are still consistent, but they are only taking 1-5% cpu now, instead of 100%. Not sure if there is a work around, as I like cache dirs

December 31, 2020

Any progress on this at all? I've been experiencing this same exact issue for a couple weeks now. 100% cpu usage, htop shows shfs using 50%, tried swapping cables on it for all new. I see a lot of these threads with the same exact issue but not a ton of resolutions. Screen shot attached. If needed I can get diags.

December 5, 2020

On 11/27/2020 at 8:53 PM, Michael_P said:

Yeah, your drives were likely dropping due to the power sagging. Don't use splitters if you can avoid it at all - and if you must, make sure they're the punch down type where you can see the pins attached to the wires and NOT the molded type. I can't stress enough how important it is to avoid the molded splitters.

Michael, I think your hunch may have been correct. The array has been running solid for a week now, so we'll see. I will have to double check the type of splitter I have, but I'm pretty sure its the punch down type. I did a bit of research on that, so thank you for the heads up!

November 27, 2020

I removed all the splitters that were there, and have changed the configuration to the following with brand new splitters and PSU SATA/MOLEX wires to hopefully even out the load:

PSU SATA Port: No splitter in play

CACHE (SSD)

DISK2

DISK4

PSU MOLEX Port:

SPLITTER 1 - PARITY + DISK1 + DISK3 - MOLEX TO SATA

SPLITTER 2 - 1x 140mm + 2x 92mm fans - MOLEX TO MOLEX

I triggered a parity sync / data rebuild, so we'll see what happens.

November 27, 2020

Looks like I'm running a Corsair SF450 PSU, which has 2 modular ports for SATA and MOLEX. At most, I will run 5 HDDs and 1 Cache, but typically its 4 HDD and 1 Cache. I do have splitters, so the set up looks like this currently:

PSU SATA Port: No splitters in play

Cache(SSD)

Disk 4 - WD Red 6TB - Disk not in array, usually my pre-clear or emergency SATA drive slot

PSU MOLEX Port:

SPLITTER 1 - PARITY + DISK1 - MOLEX TO SATA

SPLITTER 2 - DISK2 + DISK3 - MOLEX TO SATA

SPLITTER 3 - 1x 140mm + 2x 92mm fans - MOLEX TO MOLEX

To my knowledge (and googling), SATA connectors have 12V, 5V and 3.3V wires, molex uses only first 2 (12 and 5V) and SATA HDD never really used the 3.3v rail... just +12v and +5v. SSDs generally use just the +5v alone.

Power Specifications (SF450 specs)

3.3V 5V 12V 5VSB -12V

Max. Power Amps

15 20 37.5 2.5 0.3

Watts

100 450 12.5 3.6

Also looks like the EFRX 6TB drives use 1.75 amps at peak, and 5.3 watts for read / write, everything looks like it should be able to power everything correctly, and my typical power draw is ~40 watts idling.

November 27, 2020

that's a great point, let me take a look tonight and I'll report back. Thanks for the idea

November 26, 2020

So I swapped out all the SATA cables, put assigned one of the 'possibly questionable but precleared perfectly fine' disks into the disk 2 array slot, rebuilt/validated the array, and within a few hours of the rebuild, there were disk read warnings for Disk 2, but it did not disable the disk. 2 days later Disk 2 is now disabled drive. I've attached the diagnostics, but I'm not sure where to go from here. I can put the other 'possibly questionable but precleared perfectly fine' disks into the disk2 slot and run the array rebuild/validation, but I'm really getting demoralized having to do this each week now, something is obviously wrong. Not sure if its the disks, or the actual SATA port on the mobo, but I believe the 'disk 2' slot when it failed twice before was on 2 different SATA ports (old cables at the time though).

Does anyone have any insight on what is wrong possibly? looks to be the same read errors again

tower-diagnostics-20201126-1530.zip

November 17, 2020

thanks trurl, I agree I should have posted earlier but I definitely didn't think it would reoccur as often as it had. I'll try to swap out the SATA cables with new ones tonight and see how that goes. Is there a possibility that it may be something other than the cables/connections? (mobo possibly)?

Thanks again for taking a look, I was hoping that log-wise it looked like a bad connection, but I wasn't sure. I'll post back when I've made some progress

November 17, 2020

Hey all,

I'm trying to get to the root cause of several disk read errors that I've been experiencing. Earlier this year, I experienced my first red X due to several read and write errors, so I RMA'd the drive, smooth sailing after. October 19, I had another drive appear with a red X, with only read errors. I swapped that out with a spare drive, began the rebuild, and also performed a pre clear on the 'bad' disk. Array rebuilt correctly, pre clear was successful, so again, I had another spare drive to use for later on. November 9, I had yet another (different) drive appear with a red X for read errors. I swapped this drive out for the drive that i pre-cleared from October, parity was rebuilt/verified successfully. A week later, (November 17) I have another red X, but this is on the disk I had just swapped in (the disk that had errors in October, but pre-cleared just fine).

I'm at a loss here, and I am currently down 2 drives (1 spare, 1 for the array, so I am without parity). I did swap out the SATA cable in October for the 1 drive, but I just purchased a 6 pack of SATA cables that I plan to replace all the existing cables with.

I've attached all 3 diag logs for each occasion, and the smart check for the disk that has errored out twice now. I'm not entirely sure what I'm looking for, if anyone can assist, or have any ideas on where I can start/continue to troubleshoot, any help would be much appreciated.

glados-diagnostics-20201117-1341.zip glados-diagnostics-20201109-1007.zip glados-smart-20201019-2052.zip glados-diagnostics-20201019-1040.zip

December 17, 2019

On 11/20/2019 at 3:34 AM, noisegate said:

Just updated radarr and i now get this error and can't get to the web GUI:

Info] Bootstrap: Starting Radarr - /opt/radarr/Radarr.exe - Version 0.2.0.1358
[Info] AppFolderInfo: Data directory is being overridden to [/config]

[Fatal] ConsoleApp: EPIC FAIL!

[v0.2.0.1358] NzbDrone.Core.Configuration.InvalidConfigFileException: /config/config.xml is empty. Please delete the config file and Radarr will recreate it.
at NzbDrone.Core.Configuration.ConfigFileProvider.LoadConfigFile () [0x0003c] in C:\projects\radarr-usby1\src\NzbDrone.Core\Configuration\ConfigFileProvider.cs:321
at NzbDrone.Core.Configuration.ConfigFileProvider+<>c__DisplayClass45_0.<GetValue>b__0 () [0x00000] in C:\projects\radarr-usby1\src\NzbDrone.Core\Configuration\ConfigFileProvider.cs:227
at NzbDrone.Common.Cache.Cached`1[T].Get (System.String key, System.Func`1[TResult] function, System.Nullable`1[T] lifeTime) [0x0006a] in C:\projects\radarr-usby1\src\NzbDrone.Common\Cache\Cached.cs:81
at NzbDrone.Core.Configuration.ConfigFileProvider.GetValue (System.String key, System.Object defaultValue, System.Boolean persist) [0x00022] in C:\projects\radarr-usby1\src\NzbDrone.Core\Configuration\ConfigFileProvider.cs:225
at NzbDrone.Core.Configuration.ConfigFileProvider.get_LogLevel () [0x00000] in C:\projects\radarr-usby1\src\NzbDrone.Core\Configuration\ConfigFileProvider.cs:181
at NzbDrone.Core.Instrumentation.ReconfigureLogging.Reconfigure () [0x00000] in C:\projects\radarr-usby1\src\NzbDrone.Core\Instrumentation\ReconfigureLogging.cs:22
at Radarr.Host.Bootstrap.Start (Radarr.Host.ApplicationModes applicationModes, NzbDrone.Common.EnvironmentInfo.StartupContext startupContext) [0x00000] in C:\projects\radarr-usby1\src\NzbDrone.Host\Bootstrap.cs:61
at Radarr.Host.Bootstrap.Start (NzbDrone.Common.EnvironmentInfo.StartupContext startupContext, Radarr.Host.IUserAlert userAlert, System.Action`1[T] startCallback) [0x00075] in C:\projects\radarr-usby1\src\NzbDrone.Host\Bootstrap.cs:39
at NzbDrone.Console.ConsoleApp.Main (System.String[] args) [0x00029] in C:\projects\radarr-usby1\src\NzbDrone.Console\ConsoleApp.cs:35

Press enter to exit...

Any ideas how to fix this?

Did you ever find a solution for this? I'm experiencing the same thing after an update this morning.

Appdata is pointed at /mnt/cache/appdata/radarr

*********

[v0.2.0.1450] NzbDrone.Core.Configuration.InvalidConfigFileException: /config/config.xml is empty. Please delete the config file and Radarr will recreate it.
at NzbDrone.Core.Configuration.ConfigFileProvider.LoadConfigFile () [0x0003c] in C:\projects\radarr-usby1\src\NzbDrone.Core\Configuration\ConfigFileProvider.cs:321
at NzbDrone.Core.Configuration.ConfigFileProvider+<>c__DisplayClass45_0.<GetValue>b__0 () [0x00000] in C:\projects\radarr-usby1\src\NzbDrone.Core\Configuration\ConfigFileProvider.cs:227
at NzbDrone.Common.Cache.Cached`1[T].Get (System.String key, System.Func`1[TResult] function, System.Nullable`1[T] lifeTime) [0x0006a] in C:\projects\radarr-usby1\src\NzbDrone.Common\Cache\Cached.cs:81
at NzbDrone.Core.Configuration.ConfigFileProvider.GetValue (System.String key, System.Object defaultValue, System.Boolean persist) [0x00022] in C:\projects\radarr-usby1\src\NzbDrone.Core\Configuration\ConfigFileProvider.cs:225
at NzbDrone.Core.Configuration.ConfigFileProvider.get_LogLevel () [0x00000] in C:\projects\radarr-usby1\src\NzbDrone.Core\Configuration\ConfigFileProvider.cs:181
at NzbDrone.Core.Instrumentation.ReconfigureLogging.Reconfigure () [0x00000] in C:\projects\radarr-usby1\src\NzbDrone.Core\Instrumentation\ReconfigureLogging.cs:22
at Radarr.Host.Bootstrap.Start (Radarr.Host.ApplicationModes applicationModes, NzbDrone.Common.EnvironmentInfo.StartupContext startupContext) [0x00000] in C:\projects\radarr-usby1\src\NzbDrone.Host\Bootstrap.cs:61
at Radarr.Host.Bootstrap.Start (NzbDrone.Common.EnvironmentInfo.StartupContext startupContext, Radarr.Host.IUserAlert userAlert, System.Action`1[T] startCallback) [0x00075] in C:\projects\radarr-usby1\src\NzbDrone.Host\Bootstrap.cs:39
at NzbDrone.Console.ConsoleApp.Main (System.String[] args) [0x00029] in C:\projects\radarr-usby1\src\NzbDrone.Console\ConsoleApp.cs:35

August 11, 2019

On 8/9/2019 at 8:41 AM, aptalca said:

Everything's already installed. You just edit the nginx config to enable it however you like

Where is the country DB? I'm only seeing the Cities one under var/lib/libmaxminddb/GeoLite2-City.mmdb

April 26, 2019

Has there been any traction with this? I'm in the same boat, not a whole lot of experience with recipe managers or setting up container templates.

June 26, 2018

14 hours ago, aptalca said:

? Delugevpn uses its vpn tunnel for incoming connections. They don't come through the wan. Not sure how the host iptables would block that. It may be possible, but I'm not a networking guru

Even for just the website? (not actual download/upload traffic). Figured if I went to domain.com/deluge, my external IP hitting that site should be able to get logged correctly because its going through Nginx reverse proxy to get there.

I mainly just want to stop anyone from brute forcing their way into my deluge client.

June 25, 2018

On 3/17/2017 at 4:06 AM, dmacias said:
This works for me. Add the real ip lines to the nginx default site-confs for the nextcloud docker. Then restart the nextcloud docker.
server {
  listen 443 ssl;
  server_name _;

  real_ip_header X-Forwarded-For;
  set_real_ip_from 172.17.0.0/16;
  real_ip_recursive on;

I'm trying to do something similar here, but have been unable to get it to work. I'm trying to get Fail2ban working with DelugeVPN, using LetsEncrypt reverse proxy.

Everything is setup and functional, but in the DelugeVPN logs, I get 172.17.0.0/16 ips listed from the docker bridge.

******

2018-06-25 13:55:28,812 DEBG 'deluge-web-script' stderr output:
[ERROR ] 13:55:28 auth:330 Login failed (ClientIP 172.17.0.1)

******

I've set up the real ip stuff that I've seen in this thread

******

server {
   listen 443 ssl;
   server_name deluge.domain.com;

   set_real_ip_from 172.17.0.0/16;
   real_ip_header X-Forwarded-For;
   real_ip_recursive on;

   location / {
       proxy_pass http://192.168.50.50:8112/;

}
}

******

Not sure how to get the clients actual IP to populate in the delugevpn logs instead of the bridge IPs. Anyone have an idea?

June 21, 2018

I’ve had this happen too when connecting to certain Linux distributions. I’m not sure why it happens. It’s a TLS communication issue between guacd and whatever VNC you’re connecting to. I’ve reported the issue through Apache. They at least know about it. BTW, it also affects their own guacd Docker.

Appreciate the fast response. Bummer tho! Glad it's not totally a one off issue.

Great work on the container, thanks again!

Sent from my SM-G930V using Tapatalk

June 20, 2018

I'm using Unraid with Nginx reverse proxy, I've spun up VNCWebBrowser and your ApacheGuacamole container. Everything is communicating, however, I get (frequent) intermittent disconnects when the session is established, seems to happen only when I'm typing or clicking.

I've tried using VNC (port 5901) locally, as well as the HTML5 (port 6901), that works fine, its only when I'm accessing that container via ApacheGuacamole that I experience the disconnects.

Not really sure where to go from here, any help would be appreciated. Please let me know if I can provide anything else.

I have 2 different Nginx confs:

######################################################################

Conf1

map $http_upgrade $connection_upgrade {
default upgrade;
'' close;
}

server {
listen 80 default_server;
server_name _;
return 404;
}

server {
   listen 443 ssl default_server;
   root /config/www;
   index index.html index.htm index.php;

   server_name _;
add_header Strict-Transport-Security "max-age=31536000";
   ##SSL##
   #...
   #...
   ##END SSL##

   #VNC Web Browser

   location ^~ /guacamole/ {
       proxy_pass http://192.168.15.5:8086/guacamole/;
   }

   location ^~ /guacamole/websocket-tunnel {
       proxy_pass http://192.168.15.5:8086/guacamole/websocket-tunnel;
       proxy_http_version 1.1;
       proxy_set_header Upgrade $http_upgrade;
       proxy_set_header Connection $http_connection;
       #proxy_set_header Connection "upgrade";

       proxy_buffering off;
       proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;
       access_log off;

   }

}

Conf2

# GUACAMOLE CONTAINER
server {
   listen 80;
   server_name guacamole.*;
   return 404;
}

server {
listen 443 ssl http2;
server_name guacamole.*;

   ##SSL##
    #...
    #...

   add_header Strict-Transport-Security "max-age=63072000; includeSubDomains; preload";
   add_header X-Content-Type-Options nosniff;
   add_header X-XSS-Protection "1; mode=block";
   add_header X-Robots-Tag none; #SET THIS TO index IF YOU WANT GOOGLE TO INDEX YOU SITE!
   add_header Content-Security-Policy "frame-ancestors https://*.$server_name https://$server_name";
   #add_header X-Frame-Options "ALLOW-FROM https://*.$server_name" always;
   add_header X-Frame-Options "ALLOW-FROM https://*.$server_name" always;

   add_header Referrer-Policy "strict-origin-when-cross-origin";
   proxy_cookie_path / "/; HTTPOnly; Secure";
   more_set_headers "Server: Classified";
   more_clear_headers 'X-Powered-By';
   ##END SSL##

   location / {
       proxy_pass http://192.168.15.5:8086/;
       proxy_buffering off;
       proxy_set_header Upgrade $http_upgrade;
       proxy_set_header Connection $http_connection;
       proxy_set_header X-Real-IP $remote_addr;
       proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for;
       proxy_set_header X-Forwarded-Proto $scheme;
       proxy_http_version 1.1;
       proxy_no_cache $cookie_session;

       }
}

Here are the logs from the disconnects, they errors vary depending on which url (conf) I'm trying to access.

Conf1 error log

Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/lodash/2.4.1/dist/lodash.min.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/angular-translate-interpolation-messageformat/2.8.0/angular-translate-interpolation-messageformat.min.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/angular/1.3.16/angular.min.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/angular-route/1.3.16/angular-route.min.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/jquery/2.1.3/dist/jquery.min.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/angular-touch/1.3.16/angular-touch.min.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/filesaver/1.3.3/FileSaver.min.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/messageformat/1.0.2/messageformat.min.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/blob-polyfill/1.0.20150320/Blob.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/angular-translate/2.8.0/angular-translate.min.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/angular-module-shim/0.0.4/angular-module-shim.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/angular-translate-loader-static-files/2.8.0/angular-translate-loader-static-files.min.js
Jun 20, 2018 3:54:42 PM org.webjars.servlet.WebjarsServlet doGet
INFO: Webjars resource requested: /META-INF/resources/webjars/angular-cookies/1.3.16/angular-cookies.min.js
15:54:42.965 [http-nio-8080-exec-3] WARN o.a.i.d.pooled.PooledDataSource - Execution of ping query 'SELECT 1' failed: Communications link failure

The last packet successfully received from the server was 1,407,658 milliseconds ago. The last packet sent successfully to the server was 7 milliseconds ago.
15:54:42.966 [http-nio-8080-exec-3] WARN o.a.i.d.pooled.PooledDataSource - Execution of ping query 'SELECT 1' failed: Communications link failure

The last packet successfully received from the server was 1,389,637 milliseconds ago. The last packet sent successfully to the server was 0 milliseconds ago.
15:54:48.585 [http-nio-8080-exec-7] INFO o.a.g.r.auth.AuthenticationService - User "smakdafrog" successfully authenticated from 172.17.0.1.
15:54:49.270 [http-nio-8080-exec-13] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" connected to connection "1".
15:54:57.540 [http-nio-8080-exec-14] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" disconnected from connection "1". Duration: 8269 milliseconds
15:54:59.061 [http-nio-8080-exec-9] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" connected to connection "1".

Conf2 error log

15:39:37.544 [http-nio-8080-exec-14] INFO o.a.g.r.auth.AuthenticationService - User "smakdafrog" successfully authenticated from [199.102.91.33, 172.17.0.1].
15:39:38.369 [http-nio-8080-exec-1] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" connected to connection "1".
15:39:52.413 [http-nio-8080-exec-8] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" disconnected from connection "1". Duration: 14038 milliseconds
15:40:07.633 [http-nio-8080-exec-1] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" connected to connection "1".
15:52:38.722 [http-nio-8080-exec-16] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" disconnected from connection "1". Duration: 751088 milliseconds
15:52:38.742 [http-nio-8080-exec-16] WARN o.a.i.d.pooled.PooledDataSource - Execution of ping query 'SELECT 1' failed: Communications link failure

The last packet successfully received from the server was 751,058 milliseconds ago. The last packet sent successfully to the server was 15 milliseconds ago.
15:52:54.077 [http-nio-8080-exec-4] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" connected to connection "1".
15:53:11.657 [http-nio-8080-exec-2] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" disconnected from connection "1". Duration: 17580 milliseconds
15:53:26.934 [http-nio-8080-exec-9] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" connected to connection "1".
15:53:49.633 [http-nio-8080-exec-6] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" disconnected from connection "1". Duration: 22699 milliseconds
15:53:51.547 [http-nio-8080-exec-12] INFO o.a.g.tunnel.TunnelRequestService - User "smakdafrog" connected to connection "1".

June 12, 2018

2 hours ago, Squid said:

Shot in the dark, but can you access your flash drive?

yessir.

June 11, 2018

I've tried to install this plugin, but each time I get the following error.

Couldn't find /boot mount point in SNMP out. Output:

End of MIB

plugin: run failed: /bin/bash retval: 1

Anyone familiar with this error or how to fix it? I've scoured the internet, I have perl installed.

July 7, 2017

On a slightly different note, I was never able to get my Win10 vm to boot until I changed the CPU Mode to emulated instead of host pass through (Intel Pentium G4560). Id still like to get that working at some point but I haven't seen anyone have the same issue as me. This also is the same CPU I'm trying to pass the iGPU from.

Sent from my SM-G930V using Tapatalk

July 7, 2017

My bios has iGPU as primary. I can passthrough integrated or discrete GPU. I can passthrough iGPU without discrete installed using i440fx-2.7 and seaBIOS.
Both Win10 & LibreELEC tested stable integrated or discrete gpu

I'll have to give this another shot then, tried this a few months back and could never get it working. Thanks!

Sent from my SM-G930V using Tapatalk

July 7, 2017

Have you tried setting your integrated GPU in BIOS as primary boot device? This will "release" your 1080 GPU for passthrough.

Does the VM work while using VNC?

What if your trying to use the integrated GPU as the pass through? Is there any way to release that for the vm at all?

Sent from my SM-G930V using Tapatalk

smakdafrog

Posts

Joined

Last visited

Content Type

Profiles

Forums

Downloads

Store

Gallery

Bug Reports

Documentation

Landing

Posts posted by smakdafrog

Unraid 6.8.3 Random bouts of 100% CPU useage. Making server useless.

Unraid 6.8.3 Random bouts of 100% CPU useage. Making server useless.

Disks Intermittently Disabled (X) / Read errors

Disks Intermittently Disabled (X) / Read errors

Disks Intermittently Disabled (X) / Read errors

Disks Intermittently Disabled (X) / Read errors

Disks Intermittently Disabled (X) / Read errors

Disks Intermittently Disabled (X) / Read errors

Disks Intermittently Disabled (X) / Read errors

[Support] Linuxserver.io - Radarr

[Support] Linuxserver.io - SWAG - Secure Web Application Gateway (Nginx/PHP/Certbot/Fail2ban)

[Request] - container for OpenEats (recipe manager)

[Support] Linuxserver.io - SWAG - Secure Web Application Gateway (Nginx/PHP/Certbot/Fail2ban)

[Support] Linuxserver.io - SWAG - Secure Web Application Gateway (Nginx/PHP/Certbot/Fail2ban)

[Support] jasonbean - Apache Guacamole

[Support] jasonbean - Apache Guacamole

[Plug-In] SNMP

[Plug-In] SNMP

Intel IGD (integrated graphics) Pass Through Support - March 2016 Update

Intel IGD (integrated graphics) Pass Through Support - March 2016 Update

Intel IGD (integrated graphics) Pass Through Support - March 2016 Update