devastator

I'm using the one attached to the first post in this thread.

The script just halted at 88 % postread on my 2 D10EADS-00L5B1 drives. What should I do / where do I have to look for ? Greets, Deva EDIT: smartctl shows this: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. was: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Also, nothing funky returned: root@tower:/tmp# smartctl -a /dev/sda smartctl version 5.38 [i486-slackware-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD10EADS-00L5B1 Serial Number: WD-WCAU42804491 Firmware Version: 01.01A01 User Capacity: 1,000,203,804,160 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sat Jan 3 23:08:00 2009 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 166 165 021 Pre-fail Always - 6666 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 21 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 37 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 18 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 5 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 21 194 Temperature_Celsius 0x0022 126 117 000 Old_age Always - 24 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

Hey Guys, My hardware finally arrived, so I can start playing ! I want to install unraid 4.4on a full slackware install, but which version do I need to use ? This link says slack 12.2, whereas in the original announcement says 12.1. So, which one is it :-) Greets, Deva

I bought a AMD 4850E, which has virtualization support. With this, I want to get KVM running on unraid. In the KVM I'll be running mythbuntu and Windows. I'll keep you updated. Gr, Deva

This look interesting. Will give it a shot once my hardware has arrived. Gr, Deva

No screenshot included :-) What I usually do, is dump the rapidshare cookie from firefox and move it to my server. There I have a file called download.txt, which I parse like this: while read line; do wget --load-cookies /path/to/cookies -c $line done < download.txt Gr, Deva

Thanks for your comments guys ! Will order this board today, and will post the results later on ! Gr, Deva

thanks ! Seems to be difficult to find a decent mobo for an AMD Athlon 64 x2 build ...

Any recommendation you can make here about the mobo ? GA-MA74GM-S2H ? Which passive cooling can i fit on the CPU ?

Hey guys, I'm planning to build a new fileserver/mythtv backend using unraid. I'll be running mythv (MythBuntu) in a VMware session. I was thinking about the following setup: * CPU: AMD Athlon X2 5050e 2.6GHz 1MB 45W AM2 Box * MoBo: Asus M3N78 GeForce 8200, SATA2 RAID, GLAN * PSU: Be Quiet Powersupply Straight Power 600W * Case: Cooler Master Midi Tower Centurion 590 ATX No PSU * Mem: OCZ 2x2GB DDR2 SDRAM PC8500 CL5.0 Gold Edition * DISK: 2x Western Digital 640GB SATA300 16MB, WD6400AACS and 2x PATA disks from my old machine Any thoughts/ comments ? Deva