thejinx0r

Hi, I'm looking into getting a "new" for my machine with either 2xe5 2690 v1 or an amd thread ripper 1950x. Besides TDP and maybe fewer pci e lanes, what would be the difference à newer cpu and an older cpu? I plan to use this computer as a workstation with the vm running on top of unraid. Thanks

It's sort of the right command. You aren't using the right paths. You should be using your mount points. e.g. if you mounted /dev/sde to /Folder1 and /dev/sdn to /Folder2 then you would use "nohup cp -r /Folder1/Media /Folder2" (note the -r for recursive, meaning it will copy the folders and what's in it) if you want to use rsync: "nohup rsync -av /Folder1/Media /Folder2" PS: you need the ampersand symbol but my keyboard is missing the key to make the ampersand.

Everything looks fine. If you add up the size of your drives from df, (or "df -h"), it does give you 11TB. I think you are simply mistaking shfs as showing the size of your array. It's not. It's the total size of your user shares. You simply need to go to Share Settings under settings ("http://tower/Settings/ShareSettingsMenu") and add your disk 5 to your included disks in user shares.

Hi, I just saw this thread, and I want to say that this worked for me too

Thank you

I have a silly question: I'm trying to do some cable management in my computer case and 'future proofing' it. Is it bad to leave SATA cables unattached to hard drives? I want to leave one side attached to my motherboard and run them to where they will attach in the future. I don't see why it would be an issue, but I'd rather be safe.

Hi I got a couple of hard drives from my brother that he wasn't using anymore. I am currently preclearingnthem now, and noticed that one of the drives corresponded to this one in the thread here: http://lime-technology.com/forum/index.php?topic=2773.0. If I were to update the firmware on that drive, would I need to preclear it again? Thank you.

Hi, I was preclearing a new hard drive and then my power went out ( It had completed 3 of 5 cycles). I was going to add it to my array without re-preclearing it, but I decided to just look at the SMRT report. Well, I am a little worried about the values i'm seeing. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 112 099 006 Pre-fail Always - 42208416 3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 7 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 056 055 030 Pre-fail Always - 25772440425 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 72 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 7 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 057 048 045 Old_age Always - 43 (Min/Max 36/43) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 5 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 19 194 Temperature_Celsius 0x0022 043 052 000 Old_age Always - 43 (0 28 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 260348032581703 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 423266408125 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 97907054046 I am not sure what to do. I am trying to preclear them again, but the values went up again for the Raw_Read_Error_Rate, but I am not sure what to do. The HDD is brand new. It's a seagate 2TB hdd.

I have a Corsair TX 650 v2 http://www.corsair.com/power-supply-units/tx-series-power-supply-units/enthusiast-series-tx650-v2-80-plus-bronze-certified-650-watt-high-performance-power-supply.html I only have 5 drives + 1 2.5" drive. What would I check to see if it's the PSU that's causing the problem? Also, I'm not sure why my syslog was getting filtered before, but here it is again. syslog.txt

So update: It still doesn't work. My disk2 is still red balling. I attached the syslog this time. I guess I didn't attach them previously because they were either similar to this or it was filled with errors related to my SATA card breaking which I have now replaced. After running the "reiserfsck --rebuild-tree", it rebuilt the tree in 4 passes, but I apparently didn't save it. I thought I had saved the output, but I didn't. But just in case I missed something, I am running another reiserfsck on it to make sure everything is ok. smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZA4426638 Firmware Version: 51.0AB51 User Capacity: 2,000,398,934,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Jun 24 00:29:21 2012 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (37800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 253 164 021 Pre-fail Always - 925 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1749 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 092 092 000 Old_age Always - 6390 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 308 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 218 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 1557 194 Temperature_Celsius 0x0022 112 104 000 Old_age Always - 38 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 30 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 6374 - # 2 Short offline Completed without error 00% 6169 - # 3 Extended offline Completed without error 00% 6167 - # 4 Short offline Completed without error 00% 6161 - # 5 Extended offline Aborted by host 90% 6160 - # 6 Short offline Aborted by host 60% 6160 - # 7 Extended offline Aborted by host 20% 6160 - # 8 Short offline Aborted by host 80% 6156 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. I really don't know what else to do anymore. I even replaced the SATA cable on disk 2 in case it would help, but it hasn't. Is there any where else I can check for problems? syslog.txt

I started my array in maintenaince mde and ran a reiserfsck on it and it told me to rebuild the tree which I am doing now.

So, I figured out part of the problem. I had a faulty SATA-PCI card. I have since replaced it. I replaced it because I wasn't able to boot it with my HDD's plugged in to it and it just so happened that the disks that were giving me problems were on it. Now, I am still having a different issue. My disk2 has a red ball next to it and when I started the array, it was orange. This is the smart history: smartctl -a -d ata /dev/sdf (disk2) smartctl 5.39.1 2010-01-28 r3054 [i486-slackware-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZA4426638 Firmware Version: 51.0AB51 User Capacity: 2,000,398,934,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon Jun 18 10:40:22 2012 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (37800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 253 164 021 Pre-fail Always - 966 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1740 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 092 092 000 Old_age Always - 6257 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 301 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 216 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 1550 194 Temperature_Celsius 0x0022 115 104 000 Old_age Always - 35 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 30 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 6169 - # 2 Extended offline Completed without error 00% 6167 - # 3 Short offline Completed without error 00% 6161 - # 4 Extended offline Aborted by host 90% 6160 - # 5 Short offline Aborted by host 60% 6160 - # 6 Extended offline Aborted by host 20% 6160 - # 7 Short offline Aborted by host 80% 6156 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. And this is the syslog: Jun 18 10:33:55 Tower kernel: mdcmd (23): spinup 1 Jun 18 10:33:55 Tower kernel: mdcmd (24): spinup 2 Jun 18 10:33:55 Tower kernel: mdcmd (25): spinup 3 Jun 18 10:33:55 Tower kernel: mdcmd (26): spinup 4 Jun 18 10:34:00 Tower kernel: mdcmd (27): stop Jun 18 10:34:00 Tower kernel: md1: stopping Jun 18 10:34:00 Tower kernel: md2: stopping Jun 18 10:34:00 Tower kernel: md3: stopping Jun 18 10:34:00 Tower kernel: md4: stopping Jun 18 10:34:00 Tower kernel: md: unRAID driver removed Jun 18 10:34:00 Tower kernel: md: unRAID driver 2.1.3 installed Jun 18 10:34:00 Tower kernel: mdcmd (1): import 0 8,64 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4427079 Jun 18 10:34:00 Tower kernel: md: import disk0: [8,64] (sde) WDC_WD20EARS-00MVWB0_WD-WMAZA4427079 size: 1953514552 Jun 18 10:34:00 Tower kernel: mdcmd (2): import 1 8,16 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4413315 Jun 18 10:34:00 Tower kernel: md: import disk1: [8,16] (sdb) WDC_WD20EARS-00MVWB0_WD-WMAZA4413315 size: 1953514552 Jun 18 10:34:00 Tower kernel: mdcmd (3): import 2 8,80 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4426638 Jun 18 10:34:00 Tower kernel: md: import disk2: [8,80] (sdf) WDC_WD20EARS-00MVWB0_WD-WMAZA4426638 size: 1953514552 Jun 18 10:34:00 Tower kernel: mdcmd (4): import 3 8,0 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4452077 Jun 18 10:34:00 Tower kernel: md: import disk3: [8,0] (sda) WDC_WD20EARS-00MVWB0_WD-WMAZA4452077 size: 1953514552 Jun 18 10:34:00 Tower kernel: mdcmd (5): import 4 8,32 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4428878 Jun 18 10:34:00 Tower kernel: md: import disk4: [8,32] (sdc) WDC_WD20EARS-00MVWB0_WD-WMAZA4428878 size: 1953514552 Jun 18 10:34:00 Tower kernel: mdcmd (6): import 5 0,0 Jun 18 10:34:00 Tower emhttp: _shcmd: shcmd (93): exit status: 1 Jun 18 10:34:00 Tower avahi-daemon[2727]: WARNING: No NSS support for mDNS detected, consider installing nss-mdns! Jun 18 10:34:01 Tower kernel: md: unRAID driver removed Jun 18 10:34:01 Tower kernel: md: unRAID driver 2.1.3 installed Jun 18 10:34:01 Tower kernel: mdcmd (1): import 0 8,64 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4427079 Jun 18 10:34:01 Tower kernel: md: import disk0: [8,64] (sde) WDC_WD20EARS-00MVWB0_WD-WMAZA4427079 size: 1953514552 Jun 18 10:34:01 Tower kernel: mdcmd (2): import 1 8,16 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4413315 Jun 18 10:34:01 Tower kernel: md: import disk1: [8,16] (sdb) WDC_WD20EARS-00MVWB0_WD-WMAZA4413315 size: 1953514552 Jun 18 10:34:01 Tower kernel: mdcmd (3): import 2 8,80 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4426638 Jun 18 10:34:01 Tower kernel: md: import disk2: [8,80] (sdf) WDC_WD20EARS-00MVWB0_WD-WMAZA4426638 size: 1953514552 Jun 18 10:34:01 Tower kernel: mdcmd (4): import 3 8,0 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4452077 Jun 18 10:34:01 Tower kernel: md: import disk3: [8,0] (sda) WDC_WD20EARS-00MVWB0_WD-WMAZA4452077 size: 1953514552 Jun 18 10:34:01 Tower kernel: mdcmd (5): import 4 8,32 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4428878 Jun 18 10:34:01 Tower kernel: md: import disk4: [8,32] (sdc) WDC_WD20EARS-00MVWB0_WD-WMAZA4428878 size: 1953514552 Jun 18 10:34:01 Tower kernel: mdcmd (6): import 5 0,0 Jun 18 10:35:02 Tower kernel: md: unRAID driver removed Jun 18 10:35:02 Tower kernel: md: unRAID driver 2.1.3 installed Jun 18 10:35:02 Tower kernel: mdcmd (1): import 0 8,64 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4427079 Jun 18 10:35:02 Tower kernel: md: import disk0: [8,64] (sde) WDC_WD20EARS-00MVWB0_WD-WMAZA4427079 size: 1953514552 Jun 18 10:35:02 Tower kernel: mdcmd (2): import 1 8,16 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4413315 Jun 18 10:35:02 Tower kernel: md: import disk1: [8,16] (sdb) WDC_WD20EARS-00MVWB0_WD-WMAZA4413315 size: 1953514552 Jun 18 10:35:02 Tower kernel: mdcmd (3): import 2 8,80 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4426638 Jun 18 10:35:02 Tower kernel: md: import disk2: [8,80] (sdf) WDC_WD20EARS-00MVWB0_WD-WMAZA4426638 size: 1953514552 Jun 18 10:35:02 Tower kernel: mdcmd (4): import 3 8,0 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4452077 Jun 18 10:35:02 Tower kernel: md: import disk3: [8,0] (sda) WDC_WD20EARS-00MVWB0_WD-WMAZA4452077 size: 1953514552 Jun 18 10:35:02 Tower kernel: mdcmd (5): import 4 8,32 1953514552 WDC_WD20EARS-00MVWB0_WD-WMAZA4428878 Jun 18 10:35:02 Tower kernel: md: import disk4: [8,32] (sdc) WDC_WD20EARS-00MVWB0_WD-WMAZA4428878 size: 1953514552 Jun 18 10:35:02 Tower kernel: mdcmd (6): import 5 0,0 I am not sure what to do next.

So, is there any advice as to what I can file when RMAing it.

I was power cyclin at one point. I was trying to build slackware based unraid and power cycled quite abit during that time because I wasn't able to build a proper kernel, but I am using the regular version of unraid now. Anyways, the hard drive are quite new, anout a year old, if not 14 months. I want to RMA it, but I don't know what to file it as.

Hi, So this the smart history report. smartctl 5.40 2010-10-16 r3189 [i486-slackware-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green (Adv. Format) family Device Model: WDC WD20EARS-00MVWB0 Serial Number: WD-WMAZA4426638 Firmware Version: 51.0AB51 User Capacity: 2,000,398,934,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Jun 10 09:10:53 2012 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (37800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 253 164 021 Pre-fail Always - 1008 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1731 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0 9 Power_On_Hours 0x0032 092 092 000 Old_age Always - 6170 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 292 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 208 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 1549 194 Temperature_Celsius 0x0022 111 105 000 Old_age Always - 39 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 7 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 6169 - # 2 Extended offline Completed without error 00% 6167 - # 3 Short offline Completed without error 00% 6161 - # 4 Extended offline Aborted by host 90% 6160 - # 5 Short offline Aborted by host 60% 6160 - # 6 Extended offline Aborted by host 20% 6160 - # 7 Short offline Aborted by host 80% 6156 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. I have not added anything to my hardware.