vitis

Just to report. The system crashed once with the new 32GB kit, then I fixed the syslog setup - it is now mirrored to flash and also to my pfsense router. Since then I am "waiting" for another crash to get data - but nothing has happened. It is running 14 days now. Which is great, but it sucks because I didnt change a thing. Some containers were updated but I doubt that stuck container can cause that much damage. I will report when something happens but I have a hard time calling this issue fixed.

Thank you for your reply! I can point to my pfsense router. That has that capability if I recall correctly. I could never login in that console when the server is stuck. If I recall I could enter new lines but login didn't work. SSH also doesn't work when it happens. I can certainly remove that PR but then my logs would be flooded with what the PR solves and wouldn't be much use. The log was full just after few hours. Should I remove it? I haven't rolled back yet. Still waiting for another stuck and some possible feedback form the forum that I could apply.

Hello, happy Unraiders! I’m trying to track down a recurring stability issue that started recently on a server that had otherwise been stable for several months. The system becomes partially or completely unresponsive after anywhere from roughly 1 to 4 days of uptime. WebGUI, SSH and normal services stop responding. On at least one occasion a VM was still alive and able to send a notification while the Unraid host itself was unreachable. Persistent syslog is enabled and archived externally. Unfortunately, there is usually nothing useful immediately before the failure — logging simply stops after ordinary Docker/service messages. When the machine is dead and I press the power button the screen shows that the shutdown procedure starts but it never finishes. Unraid 7.3.2 / kernel 6.18.38 hangs every ~1–4 days host WebUI/SSH/services die VM can sometimes remain alive syslog often ends with nothing abnormal bad HDD replaced old RAM removed entirely new RAM kit still reproduces the hang boot USB corruption happened after some of the forced resets Current platform: ASUS TUF GAMING B550M-PLUS Ryzen 7 5700G LSI SAS2308 HBA, firmware 20.00.06.00 Unraid 7.3.2 / kernel 6.18.38-Unraid 2* 16 GB First fail on 28th August killed the boot drive (not bootable and not visible in BIOS) so I fixed it - didn't stick so I changed my boot drive to a new SanDisk. I had third RAM stick there, but it's out as a suspect - didn't help. I swapped old 2*16 GB kit for a new one - didn't help. One drive was turning bad so I swapped it - didn't help. Some other drives have some historical SMART warnings. In the log you can see that today I started monitoring health of the docker system (unrelated project). I am just parsing "docker info" in n8n and reading the warnings section. You can see that this happened: Normally: SSH connects, authenticates, runs the health check, exits within seconds. Around 11:54, one session suddenly takes tens of seconds. Around 12:06, multiple SSH connections begin piling up before authentication/session handling completes. Around 12:07, the system partially recovers — exactly the hiccup you noticed. Subsequent checks work again briefly. At 12:09:52–53, the final health-check connection gets as far as authentication/session start. Then the host essentially stops making progress until you reset it. The diagnostic was captured during startup so the load might seem high but it usually hovers much lower. I might try to rollback to 7.3.1. I dont recall when I upgraded but I usually dont do first day updates so it might also line up with update from 7.3.1 to 7.3.2. Do you have any suggestions? Viktor clearsky-syslog-10.10.1.202-20260924-1050.zip clearsky-diagnostics-20260924-1228.zip

Did you sort this out? I tried in the allow list these - local docker network IP, server IP, my public IP and IPs from my Cloudflare proxied domain. All of those got me rid of the warning but Collbora was not working. Solution: Add all Cloudflare IPs to the allow list Source: https://github.com/nextcloud/all-in-one#notes-on-cloudflare-proxytunnel

Hi @Mattyfaz, I tried your steps but I am failing on creating the rocketchat user. I keep getting this error message. 2020-01-02T17:43:21.893+0100 E QUERY [js] uncaught exception: Error: couldn't add user: command createUser requires authentication : _getErrorWithCode@src/mongo/shell/utils.js:25:13 DB.prototype.createUser@src/mongo/shell/db.js:1370:11 @(shell):1:1 I had to switch authorization to disabled in the config file. More reading here: https://stackoverflow.com/questions/27784956/error-couldnt-add-user-not-authorized-on-test-to-execute-command-createuser Edit: Web frontend port and the port in the rocketchat url has to correspond. Otherwise the file uploads would not work.

Hi guys, did anyone tried to video support to piwigo? https://github.com/xbgmsharp/piwigo-videojs/wiki/How-to-add-videos#add-video-support I have done the config changes but I am not sure if I can add the ffmpeg and other stuff to the container.

I just wanted to let you know that I solved this issue. I was using a template config file, which had a lot of examples and commented lines and I guess that the plugin could not handle this while inserting it's own stuff to it. I downloaded PIA's ovpn files which worked, so I changed my files to look alike the PIA ones and then it started working. It is not really a fix, it's just a workaround.

Hello, I have installed the client and I am having issues while connecting. I have a working unified ovpn profile and also ovpn/cert/ca - both verified and working. But when I am trying to connect with this Unraid client, the plugin inserts 10 lines saying "dev tap5" to my ovpn profile and that breaks it, so it does not work. Has anybody encountered this problem? You can see part of the ovpn profile below. ############################################## # Sample client-side OpenVPN 2.0 config file # dev tap5 # for connecting to multi-client server. # dev tap5 # # # This configuration can be used by multiple # # clients, however each client should have # dev tap5 # its own cert and key files. # # # # On Windows, you might want to rename this # # file so it has a .ovpn extension # ############################################## # Specify that we are a client and that we dev tap5 # will be pulling certain config file directives # from the server. client dev tap5