April 13, 20251 yr I dont know why but i never seem to be able to get a grasp on troubleshooting my drive failures. These popped up roughly coinciding with 7.0.1 reboot... I dont have anything of value to add and i cant garnish more information than the drives appear to be working but disabled and timeout upon enable? Attaching Diags from first discovered & a few reboots later if its any value for the boot init. Side note, Quote I had a bit of a cold shiver over the TBRW numbers on my parity drives, then i remind myself that just last week i received a 16GB MLC Flash drive with 2.45PBR / 0.88PBW in only ~11kHrs ~250PwrOns - health according to CrystalDisk was "Good" - I nearly died, that poor little drive was hammered daily 2TBW/day on a 16GB drive what kind of dodgy POS software clocked that up? I haven't done the math but the sustained RW speeds for it's life are probably notable too Thanks Jorge p.s. Do you accept donations? It's come to my attention I don't support independent devs nearly as much as i should. I won't make you rich, but you deserve a portion of what I'm able to give. Not sure if it's timing, luck or fact, but you always seem to be the responder when i throw up diags. But I'd hope there's more than one active interpreter in the forums. yoda-diagnostics-20250413-1335.zip yoda-diagnostics-20250414-0148.zip
April 14, 20251 yr Community Expert Apr 12 13:58:32 Yoda kernel: mpt2sas_cm0: SAS host is non-operational !!!! HBA problem, so all connected disk were dropped, make sure it's well seated and sufficiently cooled, you can also try a different PCIe slot if available. 15 hours ago, Nasha said: p.s. Do you accept donations? See the signature, thanks.
April 14, 20251 yr Author Thanks mate x2. Since the first and 2nd diags was a power down and partial disassemble to get a bit of plastic i dropped in my bottom intake fan. So all of that has been reseated but still impacting the same 2 drives. I dont have the luxury of another PCI slot, unless this bent pin 5600g i have is just bent pins and not cooked. Maybe ill finally implement the Ryzen reboots changes finally too. Ill see whether i can make magic, and report back if i fail
April 18, 20251 yr Author On 4/14/2025 at 5:28 PM, JorgeB said: Apr 12 13:58:32 Yoda kernel: mpt2sas_cm0: SAS host is non-operational !!!! HBA problem, i coldnt effect change... so i replaced the HBA and it's PCI riser HW and i thought it booted ok but no.... The parity drives have switched position.... Last time you might recall an unsolveable dual error,,,,, That was card and cables to get it to play nice. I officially have the worst MB AND CPU never again AMD. I have 4 sata ports x16 PCI3 - which takes me x1 GPU... a x1 v3 slot (HBA via mining riser) snd x16mech 8sig v2 slot which errora the HBA if i even try put it in there.... I have a 1 < 5 SATA multiplier which should put me operationally error freee but heavily compromiaed. I need 3mths....Sell off some HW, find the right board. I had case/ AIO's/fans and i had just updated my laptop as part of the refresh thinking i still had time the universe had other plans. I also have an asus workstation board with HBA... I think i'll jump on ebay now and spend $50 on a CPU and ECC DDR3 and just get away from the things that have been causing headaches since i came into vontact. Shortest path to a stable system, comes during the longest weekend of the year! THAT is my . Thanks for ypur help Jorge, but itsprobably say witj confidence it's HW Gremlins fo sho
April 18, 20251 yr Community Expert 8 minutes ago, Nasha said: The parity drives have switched position.... What do you mean by this? Drives are tracked by serial.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.