Power-on or device reset occurred on SAS drive, handle(0x0026) (Unraid V7.2.3)

January 19Jan 19

Hello together,

i got a LSI 9500-8i HBA card connected to two SAS drives. Both /dev/sdi and /dev/sdj get recognize at first start up without any issue. But after putting the system to sleep and wake it up again, the same drive /dev/sdi keeps disappearing from the system. Preclearing it, or

LSI 9500-8i details

storcli64 /c0 show

CLI Version = 007.3603.0000.0000 Oct 30, 2025

Operating system = Linux 6.12.54-Unraid

Controller = 0

Status = Success

Description = None

Product Name = HBA 9500-8i

Serial Number = xxx

SAS Address = 500062b20f06df80

PCI Address = 00:03:00:00

System Time = 01/19/2026 19:43:30

FW Package Build = 37.00.00.00

FW Version = 37.00.00.00

BIOS Version = 09.27.00.00_14.00.00.00

NVDATA Version = 37.00.00.10

PSOC FW Version = 0x003D

PSOC Part Number = 14790

Driver Name = mpt3sas

Driver Version = 48.100.00.00

Bus Number = 3

Device Number = 0

Function Number = 0

Domain ID = 0

Vendor Id = 0x1000

Device Id = 0xE6

SubVendor Id = 0x1000

SubDevice Id = 0x4060

Board Name = HBA 9500-8i

Board Assembly = 03-50077-03002

Board Tracer Number = xxx

Security Protocol = None

Package Stamp Mismatch = Yes

Physical Drives = 1

PD LIST :

=======

------------------------------------------------------------------------

EID:Slt DID State DG Size Intf Med SED PI SeSz Model Sp

------------------------------------------------------------------------

0:3 1 JBOD - 10.837 TB SAS HDD - - 4 KB HUH721212AL4200 -

------------------------------------------------------------------------

EID-Enclosure Device ID|Slt-Slot No|DID-Device ID|DG-DriveGroup

UGood-Unconfigured Good|UBad-Unconfigured Bad|Intf-Interface

Med-Media Type|SED-Self Encryptive Drive|PI-Protection Info

SeSz-Sector Size|Sp-Spun|U-Up|D-Down|T-Transition

Requested Boot Drive = Not Set

Here my drives after start up

lsscsi
[0:0:0:0]    disk    ATA      ST20000NM007D-3D SN03  /dev/sdb 
[1:0:0:0]    disk    ATA      ST20000NM007D-3D SN03  /dev/sdc 
[2:0:0:0]    disk    ATA      ST20000NM007D-3D SN01  /dev/sdd 
[3:0:0:0]    disk    ATA      ST20000NM007D-3D SN01  /dev/sde 
[4:0:0:0]    disk    ATA      ST20000NM007D-3D SN01  /dev/sdf 
[5:0:0:0]    disk    ATA      ST20000NM007D-3D SN01  /dev/sdg 
[7:0:0:0]    disk    ATA      WDC WD5000LPVT-0 1A01  /dev/sdh 
[8:0:0:0]    disk    Kingston DataTraveler 3.0 PMAP  /dev/sda 
[9:0:0:0]    disk    WDC      WUH722020BL5204  C5C0  /dev/sdi 
[9:0:1:0]    disk    HGST     HUH721212AL4200  DD08  /dev/sdj 
[9:0:2:0]    enclosu BROADCOM VirtualSES       03    -        
[N:0:0:1]    disk    CT1000P310SSD8__1                          /dev/nvme0n1
[N:1:0:1]    disk    CT2000P310SSD8__1                          /dev/nvme1n

syslog

Jan 19 06:11:55 Tower kernel: CoreFreq: SoC_SKL_VTD: request_mem_region 0xfed90000

Jan 19 06:11:55 Tower kernel: resource: resource sanity check: requesting [mem 0x00000000fedc0000-0x00000000fedcffff], which spans more than pnp 00:03 [mem 0xfedc0000-0xfedc7fff]

Jan 19 06:11:55 Tower kernel: caller Router+0xac/0xf0 [corefreqk] mapping multiple BARs

Jan 19 06:11:55 Tower kernel: CoreFreq: SoC_SKL_VTD: request_mem_region 0xfed90000

Jan 19 06:11:55 Tower kernel: resource: resource sanity check: requesting [mem 0x00000000fee00000-0x00000000fee0ffff], which spans more than Reserved [mem 0xfee00000-0xfee00fff]

Jan 19 06:11:55 Tower kernel: caller Router+0xac/0xf0 [corefreqk] mapping multiple BARs

Jan 19 06:11:55 Tower kernel: CoreFreq: SoC_SKL_VTD: request_mem_region 0xfed90000

Jan 19 06:11:55 Tower kernel: CoreFreq: Resume(6:7:19)

Jan 19 06:11:55 Tower kernel: mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])

Jan 19 06:11:55 Tower kernel: OOM killer enabled.

Jan 19 06:11:55 Tower kernel: Restarting tasks ...

Jan 19 06:11:55 Tower kernel: mei_pxp 0000:00:16.0-fbf6fcf1-96cf-4e2e-a6a6-1bab8cbe36b1: bound 0000:00:02.0 (ops i915_pxp_tee_component_ops [i915])

Jan 19 06:11:55 Tower crond[2234]: time disparity of 456 minutes detected

Jan 19 06:11:55 Tower kernel: done.

Jan 19 06:11:55 Tower kernel: random: crng reseeded on system resumption

Jan 19 06:11:55 Tower kernel: PM: suspend exit

Jan 19 06:11:55 Tower s3_sleep: Wake-up from sleep mode

Jan 19 06:11:56 Tower kernel: sd 9:0:0:0: device_block, handle(0x0026)

Jan 19 06:11:58 Tower kernel: sd 9:0:0:0: device_unblock and setting to running, handle(0x0026)

Jan 19 06:11:58 Tower kernel: sd 9:0:0:0: Power-on or device reset occurred

Jan 19 06:11:58 Tower kernel: sd 9:0:0:0: device_block, handle(0x0026)

Jan 19 06:11:59 Tower kernel: ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 06:11:59 Tower kernel: ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 06:11:59 Tower kernel: sd 5:0:0:0: [sdg] Starting disk

Jan 19 06:11:59 Tower kernel: sd 4:0:0:0: [sdf] Starting disk

Jan 19 06:11:59 Tower kernel: ata6.00: configured for UDMA/133

Jan 19 06:11:59 Tower kernel: ata5.00: configured for UDMA/133

Jan 19 06:11:59 Tower kernel: ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 06:11:59 Tower kernel: sd 1:0:0:0: [sdc] Starting disk

Jan 19 06:11:59 Tower kernel: ata2.00: configured for UDMA/133

Jan 19 06:12:00 Tower kernel: ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 06:12:00 Tower kernel: ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 06:12:00 Tower kernel: sd 2:0:0:0: [sdd] Starting disk

Jan 19 06:12:00 Tower kernel: ata3.00: configured for UDMA/133

Jan 19 06:12:00 Tower kernel: sd 3:0:0:0: [sde] Starting disk

Jan 19 06:12:00 Tower kernel: ata4.00: configured for UDMA/133

Jan 19 06:12:00 Tower kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 06:12:00 Tower kernel: sd 0:0:0:0: [sdb] Starting disk

Jan 19 06:12:00 Tower kernel: ata1.00: configured for UDMA/133

Jan 19 06:12:01 Tower kernel: sd 9:0:0:0: device_unblock and setting to running, handle(0x0026)

Jan 19 06:12:01 Tower kernel: sd 9:0:0:0: [sdi] tag#1781 UNKNOWN(0x2003) Result: hostbyte=0x01 driverbyte=DRIVER_OK cmd_age=2s

Jan 19 06:12:01 Tower kernel: sd 9:0:0:0: [sdi] tag#1781 CDB: opcode=0x88 88 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00

Jan 19 06:12:01 Tower kernel: I/O error, dev sdi, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2

Jan 19 06:12:01 Tower kernel: sd 9:0:0:0: [sdi] tag#1782 UNKNOWN(0x2003) Result: hostbyte=0x01 driverbyte=DRIVER_OK cmd_age=0s

Jan 19 06:12:01 Tower kernel: sd 9:0:0:0: [sdi] tag#1782 CDB: opcode=0x88 88 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00

Jan 19 06:12:01 Tower kernel: I/O error, dev sdi, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2

Jan 19 06:12:01 Tower kernel: Buffer I/O error on dev sdi, logical block 0, async page read

Jan 19 06:12:01 Tower kernel: mpt3sas_cm0: remove hba_port entry: 000000006b465d84 port: 1 from hba_port list

Jan 19 06:12:01 Tower emhttpd: read SMART /dev/sdh

Jan 19 06:12:01 Tower emhttpd: read SMART /dev/sdg

Jan 19 06:12:01 Tower emhttpd: read SMART /dev/sdd

Jan 19 06:12:01 Tower emhttpd: read SMART /dev/sde

Jan 19 06:12:01 Tower emhttpd: read SMART /dev/sdb

Jan 19 06:12:01 Tower emhttpd: read SMART /dev/sdf

Jan 19 06:12:01 Tower emhttpd: read SMART /dev/sdc

Jan 19 06:12:01 Tower emhttpd: read SMART /dev/sdi

Jan 19 06:12:01 Tower kernel: sd 9:0:0:0: [sdi] Synchronizing SCSI cache

Jan 19 06:12:01 Tower kernel: sd 9:0:0:0: [sdi] Synchronize Cache(10) failed: Result: hostbyte=0x01 driverbyte=DRIVER_OK

Jan 19 06:12:01 Tower kernel: mpt3sas_cm0: mpt3sas_transport_port_remove: removed: sas_addr(0x5000cca2c7031e5d)

Jan 19 06:12:01 Tower kernel: mpt3sas_cm0: removing handle(0x0026), sas_addr(0x5000cca2c7031e5d)

Jan 19 06:12:01 Tower kernel: mpt3sas_cm0: enclosure logical id(0x300062b20f09df80), slot(1)

Jan 19 06:12:01 Tower kernel: mpt3sas_cm0: enclosure level(0x0000), connector name( C0.0)

Jan 19 06:12:01 Tower webgui: Successful login user root from 192.xxx.xxx.xxx

Jan 19 06:12:02 Tower emhttpd: read SMART /dev/sdj

Jan 19 06:12:02 Tower emhttpd: spinning down /dev/sdh

Jan 19 06:12:02 Tower emhttpd: spinning down /dev/sdg

Jan 19 06:12:02 Tower emhttpd: spinning down /dev/sdd

Jan 19 06:12:02 Tower emhttpd: spinning down /dev/sde

Jan 19 06:12:02 Tower emhttpd: spinning down /dev/sdb

Jan 19 06:12:02 Tower emhttpd: spinning down /dev/sdf

Jan 19 06:12:02 Tower emhttpd: spinning down /dev/sdc

Jan 19 06:12:03 Tower emhttpd: offline: WUH722020BL5204_xxxxxxxx_35000cca2c7031e5c (sdi) 4096 4882956288

Jan 19 06:12:14 Tower sshd-session[1110560]: Connection from 192.xxx.xxx.xxx port 47670 on 192.xxx.xxx.xxx port 22 rdomain ""

Jan 19 06:12:14 Tower sshd-session[1110560]: Accepted key ED25519 SHA256:XXX found at /root/.ssh/authorized_keys:1

Jan 19 06:12:14 Tower sshd-session[1110560]: Postponed publickey for root from 192.xxx.xxx.xxx port 47670 ssh2 [preauth]

Jan 19 06:12:14 Tower fanctrlplus: [HDDBay_oben] Temp=*°C (Idle) → PWM=0 → RPM=0

Jan 19 06:12:16 Tower sshd-session[1110560]: Accepted key ED25519 SHA256:xxx found at /root/.ssh/authorized_keys:1

Jan 19 06:12:16 Tower sshd-session[1110560]: Accepted publickey for root from 192.xxx.xxx.xxx port 47670 ssh2: ED25519 SHA256:xxx

Jan 19 06:12:16 Tower sshd-session[1110560]: pam_unix(sshd:session): session opened for user root(uid=0) by (uid=0)

Jan 19 06:12:16 Tower elogind-daemon[2044]: New session 2 of user root.

Jan 19 06:12:16 Tower sshd-session[1110560]: User child is on pid 1110878

Jan 19 06:12:16 Tower sshd-session[1110878]: Starting session: shell on pts/0 for root from 192.xxx.xxx.xxx port 47670 id 0

Jan 19 09:21:52 Tower s3_sleep: Wake-up from sleep mode

Jan 19 09:21:52 Tower sshd-session[46812]: Connection from 192.xxx.xxx.xxx port 54340 on 192.xxx.xxx.xxx port 22 rdomain ""

Jan 19 09:21:52 Tower sshd-session[46812]: Accepted key ED25519 SHA256:XXX found at /root/.ssh/authorized_keys:1

Jan 19 09:21:52 Tower sshd-session[46812]: Postponed publickey for root from 192.xxx.xxx.xxx port 54340 ssh2 [preauth]

Jan 19 09:21:55 Tower sshd-session[46812]: Accepted key ED25519 SHA256:XXX found at /root/.ssh/authorized_keys:1

Jan 19 09:21:55 Tower sshd-session[46812]: Accepted publickey for root from 192.xxx.xxx.xxx port 54340 ssh2: ED25519 SHA256:XXX

Jan 19 09:21:55 Tower sshd-session[46812]: pam_unix(sshd:session): session opened for user root(uid=0) by (uid=0)

Jan 19 09:21:55 Tower elogind-daemon[2043]: New session 2 of user root.

Jan 19 09:21:55 Tower sshd-session[46812]: User child is on pid 47346

Jan 19 09:21:55 Tower sshd-session[47346]: Starting session: shell on pts/0 for root from 192.xxx.xxx.xxx port 54340 id 0

Jan 19 09:21:56 Tower kernel: ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 09:21:56 Tower kernel: sd 4:0:0:0: [sdf] Starting disk

Jan 19 09:21:56 Tower kernel: ata5.00: configured for UDMA/133

Jan 19 09:21:56 Tower kernel: ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 09:21:56 Tower kernel: sd 5:0:0:0: [sdg] Starting disk

Jan 19 09:21:56 Tower kernel: ata6.00: configured for UDMA/133

Jan 19 09:21:56 Tower kernel: ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 09:21:56 Tower kernel: sd 1:0:0:0: [sdc] Starting disk

Jan 19 09:21:56 Tower kernel: ata2.00: configured for UDMA/133

Jan 19 09:21:57 Tower kernel: ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 09:21:57 Tower kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 09:21:57 Tower kernel: sd 2:0:0:0: [sdd] Starting disk

Jan 19 09:21:57 Tower kernel: sd 0:0:0:0: [sdb] Starting disk

Jan 19 09:21:57 Tower kernel: ata3.00: configured for UDMA/133

Jan 19 09:21:57 Tower kernel: ata1.00: configured for UDMA/133

Jan 19 09:21:57 Tower kernel: ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 09:21:57 Tower kernel: sd 3:0:0:0: [sde] Starting disk

Jan 19 09:21:57 Tower kernel: ata4.00: configured for UDMA/133

Jan 19 09:22:02 Tower kernel: sd 9:0:1:0: Power-on or device reset occurred

Jan 19 09:22:08 Tower kernel: sd 9:0:0:0: Power-on or device reset occurred

Jan 19 18:54:04 Tower s3_sleep: Wake-up from sleep mode

Jan 19 18:54:08 Tower kernel: ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 18:54:08 Tower kernel: sd 4:0:0:0: [sdf] Starting disk

Jan 19 18:54:08 Tower kernel: ata5.00: configured for UDMA/133

Jan 19 18:54:08 Tower kernel: ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 18:54:08 Tower kernel: sd 5:0:0:0: [sdg] Starting disk

Jan 19 18:54:08 Tower kernel: ata6.00: configured for UDMA/133

Jan 19 18:54:08 Tower kernel: ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 18:54:08 Tower kernel: sd 1:0:0:0: [sdc] Starting disk

Jan 19 18:54:08 Tower kernel: ata2.00: configured for UDMA/133

Jan 19 18:54:09 Tower kernel: ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 18:54:09 Tower kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 18:54:09 Tower kernel: sd 0:0:0:0: [sdb] Starting disk

Jan 19 18:54:09 Tower kernel: sd 3:0:0:0: [sde] Starting disk

Jan 19 18:54:09 Tower kernel: ata1.00: configured for UDMA/133

Jan 19 18:54:09 Tower kernel: ata4.00: configured for UDMA/133

Jan 19 18:54:09 Tower kernel: ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

Jan 19 18:54:09 Tower kernel: sd 2:0:0:0: [sdd] Starting disk

Jan 19 18:54:09 Tower kernel: ata3.00: configured for UDMA/133

Jan 19 18:54:09 Tower emhttpd: read SMART /dev/sdj

Jan 19 18:54:09 Tower emhttpd: read SMART /dev/sdh

Jan 19 18:54:09 Tower emhttpd: read SMART /dev/sdg

Jan 19 18:54:09 Tower emhttpd: read SMART /dev/sdd

Jan 19 18:54:09 Tower emhttpd: read SMART /dev/sde

Jan 19 18:54:09 Tower emhttpd: read SMART /dev/sdb

Jan 19 18:54:09 Tower emhttpd: read SMART /dev/sdf

Jan 19 18:54:09 Tower emhttpd: read SMART /dev/sdc

Jan 19 18:54:09 Tower emhttpd: read SMART /dev/sdi

Jan 19 18:54:10 Tower kernel: sd 9:0:0:0: device_block, handle(0x0026)

Jan 19 18:54:12 Tower kernel: sd 9:0:0:0: device_unblock and setting to running, handle(0x0026)

Jan 19 18:54:12 Tower kernel: sd 9:0:0:0: Power-on or device reset occurred

Jan 19 18:54:14 Tower kernel: sd 9:0:0:0: device_block, handle(0x0026)

Jan 19 18:54:17 Tower kernel: sd 9:0:0:0: device_unblock and setting to running, handle(0x0026)

Jan 19 18:54:17 Tower kernel: sd 9:0:0:0: [sdi] tag#1679 UNKNOWN(0x2003) Result: hostbyte=0x01 driverbyte=DRIVER_OK cmd_age=4s

Jan 19 18:54:17 Tower kernel: sd 9:0:0:0: [sdi] tag#1679 CDB: opcode=0x88 88 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00

Jan 19 18:54:17 Tower kernel: I/O error, dev sdi, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2

Jan 19 18:54:17 Tower kernel: sd 9:0:0:0: [sdi] tag#1680 UNKNOWN(0x2003) Result: hostbyte=0x01 driverbyte=DRIVER_OK cmd_age=0s

Jan 19 18:54:17 Tower kernel: sd 9:0:0:0: [sdi] tag#1680 CDB: opcode=0x88 88 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00

Jan 19 18:54:17 Tower kernel: I/O error, dev sdi, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2

Jan 19 18:54:17 Tower kernel: Buffer I/O error on dev sdi, logical block 0, async page read

Jan 19 18:54:17 Tower kernel: mpt3sas_cm0: remove hba_port entry: 0000000082b727e1 port: 1 from hba_port list

Jan 19 18:54:17 Tower kernel: mpt3sas_cm0: mpt3sas_transport_port_remove: removed: sas_addr(0x5000cca2c7031e5d)

Jan 19 18:54:17 Tower kernel: mpt3sas_cm0: removing handle(0x0026), sas_addr(0x5000cca2c7031e5d)

Jan 19 18:54:17 Tower kernel: mpt3sas_cm0: enclosure logical id(0x300062b20f09df80), slot(1)

Jan 19 18:54:17 Tower kernel: mpt3sas_cm0: enclosure level(0x0000), connector name( C0.0)

Jan 19 18:54:36 Tower crond[2232]: time disparity of 94 minutes detected

Jan 19 18:55:04 Tower emhttpd: offline: WUH722020BL5204_XXX_35000cca2c7031e5c (sdi) 4096 4882956288

Jan 19 19:00:02 Tower move: mover: started

Jan 19 19:00:02 Tower move: mover: finished

Jan 19 19:24:06 Tower emhttpd: spinning down /dev/sdj

Jan 19 19:24:06 Tower SAS Assist v2024.11.25: Spinning down device /dev/sdj

Jan 19 19:24:06 Tower emhttpd: spinning down /dev/sdh

Jan 19 19:24:06 Tower emhttpd: spinning down /dev/sdg

Jan 19 19:24:06 Tower emhttpd: spinning down /dev/sdd

Jan 19 19:24:06 Tower emhttpd: spinning down /dev/sde

Jan 19 19:24:06 Tower emhttpd: spinning down /dev/sdb

Jan 19 19:24:06 Tower emhttpd: spinning down /dev/sdf

Jan 19 19:24:06 Tower emhttpd: spinning down /dev/sdc

dmesg -w | grep -E "(mpt|scsi| sd )"

[ 0.007434] Device empty

[ 0.111408] Dynamic Preempt: voluntary

[ 0.111472] rcu: Preemptible hierarchical RCU implementation.

[ 3.760974] scsi host0: ahci

[ 3.761064] scsi host1: ahci

[ 3.761142] scsi host2: ahci

[ 3.761220] scsi host3: ahci

[ 3.761295] scsi host4: ahci

[ 3.761370] scsi host5: ahci

[ 3.761444] scsi host6: ahci

[ 3.761523] scsi host7: ahci

[ 4.571641] scsi host8: usb-storage 1-10:1.0

[ 5.591508] scsi 8:0:0:0: Direct-Access Kingston DataTraveler 3.0 PMAP PQ: 0 ANSI: 6

[ 5.592317] sd 8:0:0:0: Attached scsi generic sg0 type 0

[ 5.762848] sd 8:0:0:0: [sda] 121096320 512-byte logical blocks: (62.0 GB/57.7 GiB)

[ 5.764493] sd 8:0:0:0: [sda] Write Protect is off

[ 5.764515] sd 8:0:0:0: [sda] Mode Sense: 45 00 00 00

[ 5.765475] sd 8:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA

[ 5.780321] sd 8:0:0:0: [sda] Attached SCSI removable disk

[ 6.804763] scsi 0:0:0:0: Direct-Access ATA ST20000NM007D-3D SN03 PQ: 0 ANSI: 5

[ 6.805556] sd 0:0:0:0: [sdb] 39063650304 512-byte logical blocks: (20.0 TB/18.2 TiB)

[ 6.805581] sd 0:0:0:0: [sdb] 4096-byte physical blocks

[ 6.805629] sd 0:0:0:0: [sdb] Write Protect is off

[ 6.805636] sd 0:0:0:0: [sdb] Mode Sense: 00 3a 00 00

[ 6.805658] sd 0:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 6.805667] sd 0:0:0:0: Attached scsi generic sg1 type 0

[ 6.805722] sd 0:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes

[ 6.806275] scsi 1:0:0:0: Direct-Access ATA ST20000NM007D-3D SN03 PQ: 0 ANSI: 5

[ 6.807172] sd 1:0:0:0: [sdc] 39063650304 512-byte logical blocks: (20.0 TB/18.2 TiB)

[ 6.807198] sd 1:0:0:0: [sdc] 4096-byte physical blocks

[ 6.807225] sd 1:0:0:0: [sdc] Write Protect is off

[ 6.807237] sd 1:0:0:0: [sdc] Mode Sense: 00 3a 00 00

[ 6.807238] sd 1:0:0:0: Attached scsi generic sg2 type 0

[ 6.807270] sd 1:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 6.807342] sd 1:0:0:0: [sdc] Preferred minimum I/O size 4096 bytes

[ 6.807700] scsi 2:0:0:0: Direct-Access ATA ST20000NM007D-3D SN01 PQ: 0 ANSI: 5

[ 6.808095] sd 2:0:0:0: Attached scsi generic sg3 type 0

[ 6.808184] sd 2:0:0:0: [sdd] 39063650304 512-byte logical blocks: (20.0 TB/18.2 TiB)

[ 6.808199] sd 2:0:0:0: [sdd] 4096-byte physical blocks

[ 6.808215] sd 2:0:0:0: [sdd] Write Protect is off

[ 6.808221] sd 2:0:0:0: [sdd] Mode Sense: 00 3a 00 00

[ 6.808238] sd 2:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 6.808272] sd 2:0:0:0: [sdd] Preferred minimum I/O size 4096 bytes

[ 6.808546] scsi 3:0:0:0: Direct-Access ATA ST20000NM007D-3D SN01 PQ: 0 ANSI: 5

[ 6.809418] sd 3:0:0:0: Attached scsi generic sg4 type 0

[ 6.809551] sd 3:0:0:0: [sde] 39063650304 512-byte logical blocks: (20.0 TB/18.2 TiB)

[ 6.809566] sd 3:0:0:0: [sde] 4096-byte physical blocks

[ 6.809581] sd 3:0:0:0: [sde] Write Protect is off

[ 6.809593] sd 3:0:0:0: [sde] Mode Sense: 00 3a 00 00

[ 6.809612] sd 3:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 6.809647] sd 3:0:0:0: [sde] Preferred minimum I/O size 4096 bytes

[ 6.809691] scsi 4:0:0:0: Direct-Access ATA ST20000NM007D-3D SN01 PQ: 0 ANSI: 5

[ 6.810257] sd 4:0:0:0: Attached scsi generic sg5 type 0

[ 6.810293] sd 4:0:0:0: [sdf] 39063650304 512-byte logical blocks: (20.0 TB/18.2 TiB)

[ 6.810301] sd 4:0:0:0: [sdf] 4096-byte physical blocks

[ 6.810313] sd 4:0:0:0: [sdf] Write Protect is off

[ 6.810318] sd 4:0:0:0: [sdf] Mode Sense: 00 3a 00 00

[ 6.810336] sd 4:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 6.810367] sd 4:0:0:0: [sdf] Preferred minimum I/O size 4096 bytes

[ 6.810609] scsi 5:0:0:0: Direct-Access ATA ST20000NM007D-3D SN01 PQ: 0 ANSI: 5

[ 6.810971] sd 5:0:0:0: Attached scsi generic sg6 type 0

[ 6.811098] sd 5:0:0:0: [sdg] 39063650304 512-byte logical blocks: (20.0 TB/18.2 TiB)

[ 6.811115] sd 5:0:0:0: [sdg] 4096-byte physical blocks

[ 6.811132] sd 5:0:0:0: [sdg] Write Protect is off

[ 6.811137] sd 5:0:0:0: [sdg] Mode Sense: 00 3a 00 00

[ 6.811155] sd 5:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 6.811189] sd 5:0:0:0: [sdg] Preferred minimum I/O size 4096 bytes

[ 6.811227] scsi 7:0:0:0: Direct-Access ATA WDC WD5000LPVT-0 1A01 PQ: 0 ANSI: 5

[ 6.811556] sd 7:0:0:0: Attached scsi generic sg7 type 0

[ 6.811621] sd 7:0:0:0: [sdh] 976773168 512-byte logical blocks: (500 GB/466 GiB)

[ 6.811630] sd 7:0:0:0: [sdh] 4096-byte physical blocks

[ 6.811646] sd 7:0:0:0: [sdh] Write Protect is off

[ 6.811652] sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00

[ 6.811669] sd 7:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 6.811709] sd 7:0:0:0: [sdh] Preferred minimum I/O size 4096 bytes

[ 6.863791] sd 0:0:0:0: [sdb] Attached SCSI disk

[ 6.865330] sd 3:0:0:0: [sde] Attached SCSI disk

[ 6.871848] sd 4:0:0:0: [sdf] Attached SCSI disk

[ 6.873275] sd 5:0:0:0: [sdg] Attached SCSI disk

[ 6.875678] sd 1:0:0:0: [sdc] Attached SCSI disk

[ 6.877669] sd 2:0:0:0: [sdd] Attached SCSI disk

[ 7.647571] sd 7:0:0:0: [sdh] Attached SCSI disk

[ 33.881782] mpt3sas version 48.100.00.00 loaded

[ 33.881927] mpt3sas_cm0: 63 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (32626328 kB)

[ 33.938607] mpt3sas_cm0: MSI-X vectors supported: 128

[ 33.938614] mpt3sas_cm0: 8 28 28

[ 33.939062] mpt3sas_cm0: High IOPs queues : enabled

[ 33.939064] mpt3sas0-msix0: PCI-MSI-X enabled: IRQ 180

[ 33.939065] mpt3sas0-msix1: PCI-MSI-X enabled: IRQ 181

[ 33.939066] mpt3sas0-msix2: PCI-MSI-X enabled: IRQ 182

[ 33.939066] mpt3sas0-msix3: PCI-MSI-X enabled: IRQ 183

[ 33.939067] mpt3sas0-msix4: PCI-MSI-X enabled: IRQ 184

[ 33.939068] mpt3sas0-msix5: PCI-MSI-X enabled: IRQ 185

[ 33.939069] mpt3sas0-msix6: PCI-MSI-X enabled: IRQ 186

[ 33.939069] mpt3sas0-msix7: PCI-MSI-X enabled: IRQ 187

[ 33.939070] mpt3sas0-msix8: PCI-MSI-X enabled: IRQ 188

[ 33.939071] mpt3sas0-msix9: PCI-MSI-X enabled: IRQ 189

[ 33.939072] mpt3sas0-msix10: PCI-MSI-X enabled: IRQ 190

[ 33.939073] mpt3sas0-msix11: PCI-MSI-X enabled: IRQ 191

[ 33.939074] mpt3sas0-msix12: PCI-MSI-X enabled: IRQ 192

[ 33.939074] mpt3sas0-msix13: PCI-MSI-X enabled: IRQ 193

[ 33.939075] mpt3sas0-msix14: PCI-MSI-X enabled: IRQ 194

[ 33.939076] mpt3sas0-msix15: PCI-MSI-X enabled: IRQ 195

[ 33.939077] mpt3sas0-msix16: PCI-MSI-X enabled: IRQ 196

[ 33.939078] mpt3sas0-msix17: PCI-MSI-X enabled: IRQ 197

[ 33.939078] mpt3sas0-msix18: PCI-MSI-X enabled: IRQ 198

[ 33.939079] mpt3sas0-msix19: PCI-MSI-X enabled: IRQ 199

[ 33.939080] mpt3sas0-msix20: PCI-MSI-X enabled: IRQ 200

[ 33.939081] mpt3sas0-msix21: PCI-MSI-X enabled: IRQ 201

[ 33.939081] mpt3sas0-msix22: PCI-MSI-X enabled: IRQ 202

[ 33.939082] mpt3sas0-msix23: PCI-MSI-X enabled: IRQ 203

[ 33.939083] mpt3sas0-msix24: PCI-MSI-X enabled: IRQ 204

[ 33.939084] mpt3sas0-msix25: PCI-MSI-X enabled: IRQ 205

[ 33.939085] mpt3sas0-msix26: PCI-MSI-X enabled: IRQ 206

[ 33.939085] mpt3sas0-msix27: PCI-MSI-X enabled: IRQ 207

[ 33.939086] mpt3sas_cm0: iomem(0x0000006000100000), mapped(0x00000000b25b5b80), size(1048576)

[ 33.939088] mpt3sas_cm0: ioport(0x0000000000004000), size(256)

[ 33.996605] mpt3sas_cm0: sending message unit reset !!

[ 33.998137] mpt3sas_cm0: message unit reset: SUCCESS

[ 34.024110] mpt3sas_cm0: scatter gather: sge_in_main_msg(1), sge_per_chain(7), sge_per_io(128), chains_per_io(19)

[ 34.024290] mpt3sas_cm0: request pool(0x000000005df14a55) - dma(0x158800000): depth(4872), frame_size(128), pool_size(609 kB)

[ 34.026227] mpt3sas_cm0: sense pool(0x00000000a818c509) - dma(0x15a280000): depth(4851), element_size(96), pool_size (454 kB)

[ 34.026264] mpt3sas_cm0: reply pool(0x00000000784cc4b8) - dma(0x15a300000): depth(4936), frame_size(128), pool_size(617 kB)

[ 34.026268] mpt3sas_cm0: config page(0x000000008de2fa43) - dma(0x159ccb000): size(512)

[ 34.026269] mpt3sas_cm0: Allocated physical memory: size(23560 kB)

[ 34.026270] mpt3sas_cm0: Current Controller Queue Depth(4848),Max Controller Queue Depth(4864)

[ 34.026271] mpt3sas_cm0: Scatter Gather Elements per IO(128)

[ 34.351461] mpt3sas_cm0: basedisplay_fwpkg_version: complete

[ 34.351465] mpt3sas_cm0: FW Package Ver(37.00.00.00)

[ 34.352118] mpt3sas_cm0: SAS3808: FWVersion(37.00.00.00), ChipRevision(0x00)

[ 34.352120] mpt3sas_cm0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Diag Trace Buffer,Task Set Full,NCQ)

[ 34.352248] mpt3sas_cm0: Enable interrupt coalescing only for first 8 reply queues

[ 34.352335] mpt3sas_cm0: performance mode: balanced

[ 34.352383] mpt3sas 0000:03:00.0: Max SCSIIO MPT commands: 4848 shared with nr_hw_queues = 20

[ 34.352385] scsi host9: Fusion MPT SAS Host

[ 34.352896] mpt3sas_cm0: registering trace buffer support

[ 34.356382] mpt3sas_cm0: Trace buffer memory 2048 KB allocated

[ 34.356384] mpt3sas_cm0: sending port enable !!

[ 34.356754] mpt3sas_cm0: hba_port entry: 000000005f10e3d4, port: 0 is added to hba_port list

[ 34.356853] mpt3sas_cm0: hba_port entry: 000000006b465d84, port: 1 is added to hba_port list

[ 34.357386] mpt3sas_cm0: vphy entry: 0000000090a6f384, port id: 0, phy:8 is added to port's vphys_list

[ 34.357627] mpt3sas_cm0: host_add: handle(0x0001), sas_addr(0x500062b20f06df80), phys(11)

[ 34.357864] mpt3sas_cm0: handle(0x26) sas_address(0x5000cca2c7031e5d) port_type(0x1)

[ 34.358377] scsi 9:0:0:0: Direct-Access WDC WUH722020BL5204 C5C0 PQ: 0 ANSI: 7

[ 34.358382] scsi 9:0:0:0: SSP: handle(0x0026), sas_addr(0x5000cca2c7031e5d), phy(1), device_name(0x5000cca2c7031e5f)

[ 34.358384] scsi 9:0:0:0: enclosure logical id (0x300062b20f09df80), slot(1)

[ 34.358386] scsi 9:0:0:0: enclosure level(0x0000), connector name( C0.0)

[ 34.358388] scsi 9:0:0:0: qdepth(64), tagged(1), scsi_level(8), cmd_que(1)

[ 34.362199] sd 9:0:0:0: Attached scsi generic sg8 type 0

[ 34.362450] mpt3sas_cm0: handle(0x25) sas_address(0x5000cca2b03734b1) port_type(0x1)

[ 34.362727] sd 9:0:0:0: [sdi] 4882956288 4096-byte logical blocks: (20.0 TB/18.2 TiB)

[ 34.362961] scsi 9:0:1:0: Direct-Access HGST HUH721212AL4200 DD08 PQ: 0 ANSI: 6

[ 34.362965] scsi 9:0:1:0: SSP: handle(0x0025), sas_addr(0x5000cca2b03734b1), phy(3), device_name(0x5000cca2b03734b3)

[ 34.362968] scsi 9:0:1:0: enclosure logical id (0x300062b20f09df80), slot(3)

[ 34.362969] scsi 9:0:1:0: enclosure level(0x0000), connector name( C0.0)

[ 34.362971] scsi 9:0:1:0: qdepth(64), tagged(1), scsi_level(7), cmd_que(1)

[ 34.363128] sd 9:0:0:0: [sdi] Write Protect is off

[ 34.363130] sd 9:0:0:0: [sdi] Mode Sense: f7 00 10 08

[ 34.363789] sd 9:0:0:0: [sdi] Write cache: enabled, read cache: enabled, supports DPO and FUA

[ 34.365950] sd 9:0:1:0: Attached scsi generic sg9 type 0

[ 34.366305] sd 9:0:1:0: [sdj] 2909274112 4096-byte logical blocks: (11.9 TB/10.8 TiB)

[ 34.366369] mpt3sas_cm0: handle(0x9) sas_address(0x300162b20f06df80) port_type(0x0)

[ 34.366541] scsi 9:0:2:0: Enclosure BROADCOM VirtualSES 03 PQ: 0 ANSI: 7

[ 34.366544] scsi 9:0:2:0: set ignore_delay_remove for handle(0x0009)

[ 34.366546] scsi 9:0:2:0: SES: handle(0x0009), sas_addr(0x300162b20f06df80), phy(8), device_name(0x300162b20f06df80)

[ 34.366548] scsi 9:0:2:0: enclosure logical id (0x300062b20f09df80), slot(8)

[ 34.366550] scsi 9:0:2:0: enclosure level(0x0000), connector name( C0.1)

[ 34.366552] scsi 9:0:2:0: qdepth(1), tagged(0), scsi_level(8), cmd_que(0)

[ 34.366821] scsi 9:0:2:0: Attached scsi generic sg10 type 13

[ 34.367369] sd 9:0:1:0: [sdj] Write Protect is off

[ 34.367372] sd 9:0:1:0: [sdj] Mode Sense: f7 00 10 08

[ 34.369290] sd 9:0:1:0: [sdj] Write cache: disabled, read cache: enabled, supports DPO and FUA

[ 34.377596] mpt3sas_cm0: port enable: SUCCESS

[ 34.496022] sd 9:0:0:0: [sdi] Attached SCSI disk

[ 34.499614] sd 9:0:1:0: [sdj] Attached SCSI disk

[ 83.338988] md: import_slot: 29 empty

[ 96.769111] md: import_slot: 29 empty

[10234.184498] sd 9:0:0:0: [sdi] Synchronizing SCSI cache

[10242.376661] mpt3sas_cm0: pdev=0x0000000071dc58e5, slot=0000:03:00.0, entering operating state

[10242.376689] mpt3sas_cm0: sending message unit reset !!

[10242.378202] mpt3sas_cm0: message unit reset: SUCCESS

[10242.378424] sd 5:0:0:0: [sdg] Synchronizing SCSI cache

[10242.379326] sd 7:0:0:0: [sdh] Synchronizing SCSI cache

[10242.383324] sd 4:0:0:0: [sdf] Synchronizing SCSI cache

[10242.383384] sd 3:0:0:0: [sde] Synchronizing SCSI cache

[10242.383394] sd 2:0:0:0: [sdd] Synchronizing SCSI cache

[10242.383458] sd 1:0:0:0: [sdc] Synchronizing SCSI cache

[10242.383462] sd 0:0:0:0: [sdb] Synchronizing SCSI cache

[10243.023097] mpt3sas_cm0: pdev=0x0000000071dc58e5, slot=0000:03:00.0, previous operating state [D0]

[10243.023162] mpt3sas_cm0: 63 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (32626328 kB)

[10243.092932] mpt3sas_cm0: CurrentHostPageSize is 0: Setting default host page size to 4k

[10243.092943] mpt3sas_cm0: MSI-X vectors supported: 128

[10243.092945] mpt3sas_cm0: 8 28 28

[10243.093399] mpt3sas_cm0: High IOPs queues : enabled

[10243.093400] mpt3sas0-msix0: PCI-MSI-X enabled: IRQ 179

[10243.093401] mpt3sas0-msix1: PCI-MSI-X enabled: IRQ 180

[10243.093401] mpt3sas0-msix2: PCI-MSI-X enabled: IRQ 181

[10243.093401] mpt3sas0-msix3: PCI-MSI-X enabled: IRQ 182

[10243.093402] mpt3sas0-msix4: PCI-MSI-X enabled: IRQ 183

[10243.093402] mpt3sas0-msix5: PCI-MSI-X enabled: IRQ 184

[10243.093402] mpt3sas0-msix6: PCI-MSI-X enabled: IRQ 185

[10243.093403] mpt3sas0-msix7: PCI-MSI-X enabled: IRQ 186

[10243.093403] mpt3sas0-msix8: PCI-MSI-X enabled: IRQ 187

[10243.093403] mpt3sas0-msix9: PCI-MSI-X enabled: IRQ 188

[10243.093404] mpt3sas0-msix10: PCI-MSI-X enabled: IRQ 189

[10243.093404] mpt3sas0-msix11: PCI-MSI-X enabled: IRQ 190

[10243.093404] mpt3sas0-msix12: PCI-MSI-X enabled: IRQ 191

[10243.093405] mpt3sas0-msix13: PCI-MSI-X enabled: IRQ 192

[10243.093405] mpt3sas0-msix14: PCI-MSI-X enabled: IRQ 193

[10243.093405] mpt3sas0-msix15: PCI-MSI-X enabled: IRQ 194

[10243.093406] mpt3sas0-msix16: PCI-MSI-X enabled: IRQ 195

[10243.093406] mpt3sas0-msix17: PCI-MSI-X enabled: IRQ 196

[10243.093406] mpt3sas0-msix18: PCI-MSI-X enabled: IRQ 197

[10243.093407] mpt3sas0-msix19: PCI-MSI-X enabled: IRQ 198

[10243.093407] mpt3sas0-msix20: PCI-MSI-X enabled: IRQ 199

[10243.093407] mpt3sas0-msix21: PCI-MSI-X enabled: IRQ 200

[10243.093408] mpt3sas0-msix22: PCI-MSI-X enabled: IRQ 201

[10243.093408] mpt3sas0-msix23: PCI-MSI-X enabled: IRQ 202

[10243.093408] mpt3sas0-msix24: PCI-MSI-X enabled: IRQ 203

[10243.093409] mpt3sas0-msix25: PCI-MSI-X enabled: IRQ 204

[10243.093409] mpt3sas0-msix26: PCI-MSI-X enabled: IRQ 205

[10243.093409] mpt3sas0-msix27: PCI-MSI-X enabled: IRQ 206

[10243.093410] mpt3sas_cm0: iomem(0x0000006000100000), mapped(0x00000000cf094242), size(1048576)

[10243.093411] mpt3sas_cm0: ioport(0x0000000000004000), size(256)

[10243.093489] mpt3sas_cm0: Issuing Hard Reset as part of OS Resume

[10243.093491] mpt3sas_cm0: mpt3sas_ctl_pre_reset_handler: Releasing the trace buffer due to adapter reset.

[10243.150940] mpt3sas_cm0: CurrentHostPageSize is 0: Setting default host page size to 4k

[10243.476262] mpt3sas_cm0: basedisplay_fwpkg_version: complete

[10243.476264] mpt3sas_cm0: FW Package Ver(37.00.00.00)

[10243.476865] mpt3sas_cm0: SAS3808: FWVersion(37.00.00.00), ChipRevision(0x00)

[10243.476867] mpt3sas_cm0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Diag Trace Buffer,Task Set Full,NCQ)

[10243.476987] mpt3sas_cm0: Enable interrupt coalescing only for first 8 reply queues

[10243.477071] mpt3sas_cm0: performance mode: balanced

[10243.477097] mpt3sas_cm0: sending port enable !!

[10243.697428] sd 7:0:0:0: [sdh] Starting disk

[10253.361770] mpt3sas_cm0: port enable: SUCCESS

[10253.362217] mpt3sas_cm0: search for end-devices: start

[10253.362572] scsi target9:0:2: handle(0x0009), sas_addr(0x300162b20f06df80)

[10253.362583] scsi target9:0:2: enclosure logical id(0x300062b20f09df80), slot(8)

[10253.362637] scsi target9:0:1: handle(0x0025), sas_addr(0x5000cca2b03734b1)

[10253.362645] scsi target9:0:1: enclosure logical id(0x300062b20f09df80), slot(3)

[10253.362697] scsi target9:0:0: handle(0x0026), sas_addr(0x5000cca2c7031e5d)

[10253.362704] scsi target9:0:0: enclosure logical id(0x300062b20f09df80), slot(1)

[10253.362768] mpt3sas_cm0: search for end-devices: complete

[10253.362772] mpt3sas_cm0: search for end-devices: start

[10253.362775] mpt3sas_cm0: search for PCIe end-devices: complete

[10253.362778] mpt3sas_cm0: search for expanders: start

[10253.362781] mpt3sas_cm0: search for expanders: complete

[10253.362790] mpt3sas_cm0: mpt3sas_base_hard_reset_handler: SUCCESS

[10253.362896] mpt3sas_cm0: removing unresponding devices: start

[10253.362906] mpt3sas_cm0: removing unresponding devices: end-devices

[10253.362910] mpt3sas_cm0: Removing unresponding devices: pcie end-devices

[10253.362914] mpt3sas_cm0: removing unresponding devices: expanders

[10253.362918] mpt3sas_cm0: removing unresponding devices: complete

[10253.362925] mpt3sas_cm0: Update devices with firmware reported queue depth

[10253.362938] sd 9:0:0:0: qdepth(64), tagged(1), scsi_level(8), cmd_que(1)

[10253.362951] sd 9:0:1:0: qdepth(64), tagged(1), scsi_level(7), cmd_que(1)

[10253.362959] ses 9:0:2:0: qdepth(1), tagged(0), scsi_level(8), cmd_que(0)

[10253.362965] mpt3sas_cm0: scan devices: start

[10253.363256] mpt3sas_cm0: scan devices: expanders start

[10253.363311] mpt3sas_cm0: break from expander scan: ioc_status(0x0022), loginfo(0x310f0400)

[10253.363318] mpt3sas_cm0: scan devices: expanders complete

[10253.363321] mpt3sas_cm0: scan devices: end devices start

[10253.363821] mpt3sas_cm0: break from end device scan: ioc_status(0x0022), loginfo(0x310f0400)

[10253.363827] mpt3sas_cm0: scan devices: end devices complete

[10253.363830] mpt3sas_cm0: scan devices: pcie end devices start

[10253.364229] mpt3sas_cm0: break from pcie end device scan: ioc_status(0x0022), loginfo(0x310f0400)

[10253.364234] mpt3sas_cm0: pcie devices: pcie end devices complete

[10253.364237] mpt3sas_cm0: scan devices: complete

[10253.375086] random: crng reseeded on system resumption

[10254.111881] sd 9:0:0:0: device_block, handle(0x0026)

[10255.863123] sd 9:0:0:0: device_unblock and setting to running, handle(0x0026)

[10256.069246] sd 9:0:0:0: Power-on or device reset occurred

[10256.611808] sd 9:0:0:0: device_block, handle(0x0026)

[10257.482453] sd 5:0:0:0: [sdg] Starting disk

[10257.497349] sd 4:0:0:0: [sdf] Starting disk

[10257.703650] sd 1:0:0:0: [sdc] Starting disk

[10258.071707] sd 2:0:0:0: [sdd] Starting disk

[10258.129572] sd 3:0:0:0: [sde] Starting disk

[10258.268460] sd 0:0:0:0: [sdb] Starting disk

[10258.861528] sd 9:0:0:0: device_unblock and setting to running, handle(0x0026)

[10258.861683] sd 9:0:0:0: [sdi] tag#1781 UNKNOWN(0x2003) Result: hostbyte=0x01 driverbyte=DRIVER_OK cmd_age=2s

[10258.861704] sd 9:0:0:0: [sdi] tag#1781 CDB: opcode=0x88 88 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00

[10258.861798] sd 9:0:0:0: [sdi] tag#1782 UNKNOWN(0x2003) Result: hostbyte=0x01 driverbyte=DRIVER_OK cmd_age=0s

[10258.861808] sd 9:0:0:0: [sdi] tag#1782 CDB: opcode=0x88 88 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00

[10258.862120] mpt3sas_cm0: remove hba_port entry: 000000006b465d84 port: 1 from hba_port list

[10258.895901] sd 9:0:0:0: [sdi] Synchronizing SCSI cache

[10258.895988] sd 9:0:0:0: [sdi] Synchronize Cache(10) failed: Result: hostbyte=0x01 driverbyte=DRIVER_OK

[10258.898560] mpt3sas_cm0: mpt3sas_transport_port_remove: removed: sas_addr(0x5000cca2c7031e5d)

[10258.898574] mpt3sas_cm0: removing handle(0x0026), sas_addr(0x5000cca2c7031e5d)

[10258.898580] mpt3sas_cm0: enclosure logical id(0x300062b20f09df80), slot(1)

[10258.898585] mpt3sas_cm0: enclosure level(0x0000), connector name( C0.0)

[29121.168182] mpt3sas_cm0: pdev=0x000000003dabe66d, slot=0000:03:00.0, entering operating state

[29121.168220] mpt3sas_cm0: sending message unit reset !!

[29121.168673] sd 7:0:0:0: [sdh] Synchronizing SCSI cache

[29121.168722] sd 5:0:0:0: [sdg] Synchronizing SCSI cache

[29121.169642] mpt3sas_cm0: message unit reset: SUCCESS

[29121.176778] sd 4:0:0:0: [sdf] Synchronizing SCSI cache

[29121.177681] sd 3:0:0:0: [sde] Synchronizing SCSI cache

[29121.177878] sd 1:0:0:0: [sdc] Synchronizing SCSI cache

[29121.178697] sd 0:0:0:0: [sdb] Synchronizing SCSI cache

[29121.178708] sd 2:0:0:0: [sdd] Synchronizing SCSI cache

[29121.794226] mpt3sas_cm0: pdev=0x000000003dabe66d, slot=0000:03:00.0, previous operating state [D0]

[29121.794269] mpt3sas_cm0: 63 BIT PCI BUS DMA ADDRESSING SUPPORTED, total mem (32626328 kB)

[29121.865392] mpt3sas_cm0: CurrentHostPageSize is 0: Setting default host page size to 4k

[29121.865403] mpt3sas_cm0: MSI-X vectors supported: 128

[29121.865405] mpt3sas_cm0: 8 28 28

[29121.865856] mpt3sas_cm0: High IOPs queues : enabled

[29121.865857] mpt3sas0-msix0: PCI-MSI-X enabled: IRQ 179

[29121.865858] mpt3sas0-msix1: PCI-MSI-X enabled: IRQ 180

[29121.865858] mpt3sas0-msix2: PCI-MSI-X enabled: IRQ 181

[29121.865859] mpt3sas0-msix3: PCI-MSI-X enabled: IRQ 182

[29121.865859] mpt3sas0-msix4: PCI-MSI-X enabled: IRQ 183

[29121.865859] mpt3sas0-msix5: PCI-MSI-X enabled: IRQ 184

[29121.865860] mpt3sas0-msix6: PCI-MSI-X enabled: IRQ 185

[29121.865860] mpt3sas0-msix7: PCI-MSI-X enabled: IRQ 186

[29121.865860] mpt3sas0-msix8: PCI-MSI-X enabled: IRQ 187

[29121.865861] mpt3sas0-msix9: PCI-MSI-X enabled: IRQ 188

[29121.865861] mpt3sas0-msix10: PCI-MSI-X enabled: IRQ 189

[29121.865861] mpt3sas0-msix11: PCI-MSI-X enabled: IRQ 190

[29121.865862] mpt3sas0-msix12: PCI-MSI-X enabled: IRQ 191

[29121.865862] mpt3sas0-msix13: PCI-MSI-X enabled: IRQ 192

[29121.865862] mpt3sas0-msix14: PCI-MSI-X enabled: IRQ 193

[29121.865863] mpt3sas0-msix15: PCI-MSI-X enabled: IRQ 194

[29121.865863] mpt3sas0-msix16: PCI-MSI-X enabled: IRQ 195

[29121.865863] mpt3sas0-msix17: PCI-MSI-X enabled: IRQ 196

[29121.865864] mpt3sas0-msix18: PCI-MSI-X enabled: IRQ 197

[29121.865864] mpt3sas0-msix19: PCI-MSI-X enabled: IRQ 198

[29121.865864] mpt3sas0-msix20: PCI-MSI-X enabled: IRQ 199

[29121.865865] mpt3sas0-msix21: PCI-MSI-X enabled: IRQ 200

[29121.865865] mpt3sas0-msix22: PCI-MSI-X enabled: IRQ 201

[29121.865865] mpt3sas0-msix23: PCI-MSI-X enabled: IRQ 202

[29121.865866] mpt3sas0-msix24: PCI-MSI-X enabled: IRQ 203

[29121.865866] mpt3sas0-msix25: PCI-MSI-X enabled: IRQ 204

[29121.865866] mpt3sas0-msix26: PCI-MSI-X enabled: IRQ 205

[29121.865866] mpt3sas0-msix27: PCI-MSI-X enabled: IRQ 206

[29121.865867] mpt3sas_cm0: iomem(0x0000006000100000), mapped(0x000000004e84654d), size(1048576)

[29121.865868] mpt3sas_cm0: ioport(0x0000000000004000), size(256)

[29121.865946] mpt3sas_cm0: Issuing Hard Reset as part of OS Resume

[29121.923398] mpt3sas_cm0: CurrentHostPageSize is 0: Setting default host page size to 4k

[29122.248719] mpt3sas_cm0: basedisplay_fwpkg_version: complete

[29122.248721] mpt3sas_cm0: FW Package Ver(37.00.00.00)

[29122.249329] mpt3sas_cm0: SAS3808: FWVersion(37.00.00.00), ChipRevision(0x00)

[29122.249331] mpt3sas_cm0: Protocol=(Initiator,Target), Capabilities=(TLR,EEDP,Diag Trace Buffer,Task Set Full,NCQ)

[29122.249452] mpt3sas_cm0: Enable interrupt coalescing only for first 8 reply queues

[29122.249536] mpt3sas_cm0: performance mode: balanced

[29122.249562] mpt3sas_cm0: sending port enable !!

[29122.483286] sd 7:0:0:0: [sdh] Starting disk

[29132.139437] mpt3sas_cm0: port enable: SUCCESS

[29132.139903] mpt3sas_cm0: search for end-devices: start

[29132.140258] scsi target9:0:2: handle(0x0009), sas_addr(0x300162b20f06df80)

[29132.140268] scsi target9:0:2: enclosure logical id(0x300062b20f09df80), slot(8)

[29132.140322] scsi target9:0:1: handle(0x0025), sas_addr(0x5000cca2b03734b1)

[29132.140330] scsi target9:0:1: enclosure logical id(0x300062b20f09df80), slot(3)

[29132.140386] scsi target9:0:0: handle(0x0026), sas_addr(0x5000cca2c7031e5d)

[29132.140393] scsi target9:0:0: enclosure logical id(0x300062b20f09df80), slot(1)

[29132.140460] mpt3sas_cm0: search for end-devices: complete

[29132.140463] mpt3sas_cm0: search for end-devices: start

[29132.140467] mpt3sas_cm0: search for PCIe end-devices: complete

[29132.140470] mpt3sas_cm0: search for expanders: start

[29132.140473] mpt3sas_cm0: search for expanders: complete

[29132.140481] mpt3sas_cm0: mpt3sas_base_hard_reset_handler: SUCCESS

[29132.140645] mpt3sas_cm0: removing unresponding devices: start

[29132.140664] mpt3sas_cm0: removing unresponding devices: end-devices

[29132.140672] mpt3sas_cm0: Removing unresponding devices: pcie end-devices

[29132.140677] mpt3sas_cm0: removing unresponding devices: expanders

[29132.140681] mpt3sas_cm0: removing unresponding devices: complete

[29132.140693] mpt3sas_cm0: Update devices with firmware reported queue depth

[29132.140748] sd 9:0:0:0: qdepth(64), tagged(1), scsi_level(8), cmd_que(1)

[29132.140767] sd 9:0:1:0: qdepth(64), tagged(1), scsi_level(7), cmd_que(1)

[29132.140779] ses 9:0:2:0: qdepth(1), tagged(0), scsi_level(8), cmd_que(0)

[29132.140787] mpt3sas_cm0: scan devices: start

[29132.141262] mpt3sas_cm0: scan devices: expanders start

[29132.141329] mpt3sas_cm0: break from expander scan: ioc_status(0x0022), loginfo(0x310f0400)

[29132.141341] mpt3sas_cm0: scan devices: expanders complete

[29132.141346] mpt3sas_cm0: scan devices: end devices start

[29132.142062] mpt3sas_cm0: break from end device scan: ioc_status(0x0022), loginfo(0x310f0400)

[29132.142075] mpt3sas_cm0: scan devices: end devices complete

[29132.142079] mpt3sas_cm0: scan devices: pcie end devices start

[29132.142459] mpt3sas_cm0: break from pcie end device scan: ioc_status(0x0022), loginfo(0x310f0400)

[29132.142465] mpt3sas_cm0: pcie devices: pcie end devices complete

[29132.142468] mpt3sas_cm0: scan devices: complete

[29132.152235] random: crng reseeded on system resumption

[29136.048890] sd 4:0:0:0: [sdf] Starting disk

[29136.173416] sd 5:0:0:0: [sdg] Starting disk

[29136.309740] sd 1:0:0:0: [sdc] Starting disk

[29136.740630] sd 0:0:0:0: [sdb] Starting disk

[29136.742682] sd 3:0:0:0: [sde] Starting disk

[29136.928559] sd 2:0:0:0: [sdd] Starting disk

[29137.889408] sd 9:0:0:0: device_block, handle(0x0026)

[29139.890822] sd 9:0:0:0: device_unblock and setting to running, handle(0x0026)

[29140.096563] sd 9:0:0:0: Power-on or device reset occurred

[29141.889271] sd 9:0:0:0: device_block, handle(0x0026)

[29144.639064] sd 9:0:0:0: device_unblock and setting to running, handle(0x0026)

[29144.639241] sd 9:0:0:0: [sdi] tag#1679 UNKNOWN(0x2003) Result: hostbyte=0x01 driverbyte=DRIVER_OK cmd_age=4s

[29144.639260] sd 9:0:0:0: [sdi] tag#1679 CDB: opcode=0x88 88 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00

[29144.639339] sd 9:0:0:0: [sdi] tag#1680 UNKNOWN(0x2003) Result: hostbyte=0x01 driverbyte=DRIVER_OK cmd_age=0s

[29144.639349] sd 9:0:0:0: [sdi] tag#1680 CDB: opcode=0x88 88 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00

[29144.639720] mpt3sas_cm0: remove hba_port entry: 0000000082b727e1 port: 1 from hba_port list

[29144.668820] mpt3sas_cm0: mpt3sas_transport_port_remove: removed: sas_addr(0x5000cca2c7031e5d)

[29144.668824] mpt3sas_cm0: removing handle(0x0026), sas_addr(0x5000cca2c7031e5d)

[29144.668825] mpt3sas_cm0: enclosure logical id(0x300062b20f09df80), slot(1)

[29144.668826] mpt3sas_cm0: enclosure level(0x0000), connector name( C0.0)

I switched cables, switched to a 9400-8i HBA card and this behavior still occurs. I reinstalled the Spin Down SAS Drives Plugin. First I thought the emulated sector size of 512 bytes was the problem so i low level formatted the drive, see [Guide] Low level formatting SAS drives.

Does anyone have a suggestion or hint what to do? It is driving me nuts, since I can not solve this for two weeks...

dmseg.log syslog.log

Quote

Power-on or device reset occurred on SAS drive, handle(0x0026) (Unraid V7.2.3)

Featured Replies

Join the conversation

Account

Navigation

Search

Configure browser push notifications

Chrome (Android)

Chrome (Desktop)

Safari (iOS 16.4+)

Safari (macOS)

Edge (Android)

Edge (Desktop)

Firefox (Android)

Firefox (Desktop)