Hi,

 

It has been a while, but I finally was able to tend to my server after moving. Upon new network recognition and start up, there was a parity and too many disks missing, array stopped, message. Went inside, found disconnected power and SATA cables, fixed those. But message persists.

 

I need help!

Still running 4.7. I am attaching my syslog. If needed, I have a screenprint of main page as I see it in UNMENU-forgot password and cannot go straight to main page.

 

All help will be appreciated.

Thanks,

Ramon

syslog-2016-12-24.txt

Do you have a list of the assignments, or at least know which disk was parity?

 

From what I can see unRAID is detecting 13 disks, you had 14 total, the one on ata8 is having issues, I'm guessing 4 show missing because your still on v4 and it doesn't track the disks by serial, any change in disk order, like a missing disk, can result in more missing disks.

 

These are the detected disks, do you know if the missing disk was parity or a data disk?

Dec 24 05:08:57 Tower emhttp: pci-0000:00:11.0-scsi-1:0:0:0 host3 (sdi) Hitachi_HDS722020ALA330_JK1101YAJLA3RV
Dec 24 05:08:57 Tower emhttp: pci-0000:00:11.0-scsi-2:0:0:0 host4 (sdj) Hitachi_HDS5C3020ALA632_ML0220F31AAS7N
Dec 24 05:08:57 Tower emhttp: pci-0000:00:11.0-scsi-3:0:0:0 host5 (sdk) WDC_WD20EADS-00R6B0_WD-WCAVY1405130
Dec 24 05:08:57 Tower emhttp: pci-0000:00:14.1-ide-1:0 ide1 (hdc) Hitachi_HDS5C3020ALA632_ML0220F31A79UD
Dec 24 05:08:57 Tower emhttp: pci-0000:00:14.1-ide-1:1 ide1 (hdd) Hitachi_HDS5C3020ALA632_ML0220F315MY1D
Dec 24 05:08:57 Tower emhttp: pci-0000:02:00.0-sas-phy0:1-0x0000000000000000:0-lun0 host1 (sdb) ST2000DL003-9VT166_5YD5XA5K
Dec 24 05:08:57 Tower emhttp: pci-0000:02:00.0-sas-phy2:1-0x0200000000000000:2-lun0 host1 (sdc) ST2000DL003-9VT_5YD25J25
Dec 24 05:08:57 Tower emhttp: pci-0000:02:00.0-sas-phy3:1-0x0300000000000000:3-lun0 host1 (sdd) Hitachi_HDS7220_JK1101YAK3JBVZ
Dec 24 05:08:57 Tower emhttp: pci-0000:02:00.0-sas-phy4:1-0x0400000000000000:4-lun0 host1 (sde) ST2000DL003-9VT_5YD2V4YP
Dec 24 05:08:57 Tower emhttp: pci-0000:02:00.0-sas-phy5:1-0x0500000000000000:5-lun0 host1 (sdf) Hitachi_HDS5C30_ML0220F31383PD
Dec 24 05:08:57 Tower emhttp: pci-0000:02:00.0-sas-phy6:1-0x0600000000000000:6-lun0 host1 (sdg) Hitachi_HDS5C30_ML0220F319AM0D
Dec 24 05:08:57 Tower emhttp: pci-0000:02:00.0-sas-phy7:1-0x0700000000000000:7-lun0 host1 (sdh) Hitachi_HDS5C30_ML0220F318VM3D
Dec 24 05:08:57 Tower emhttp: pci-0000:03:07.0-scsi-1:0:0:0 host7 (sdl) Hitachi_HDS722020ALA330_JK1101YAJVWJKV

 

I'm guessing the problem disk is connect to the 8 port controller.

 

Also, IIRC, v4.7 will show which disk is missing from each slot, and you should be able to select them from the dropdown box, except ata8, that one is really missing.

Thanks!

 

This helps a lot. The parity was moved-looking for a better power connector within the setup. I will move those disks about. The parity was one of the 7200 rpm Hitachi drives. I have it labeled. Will fix that.

About Disk 8, will start diagnosing there, and report back asap.

 

Thank you,

Ramon