jwong0412

I'll look into that. Thank you to everyone for all the help!

I tried to follow along the link you sent, but when I type in any commands I get the following error code.... Unknown code er3k 127

- Reformatted USB - Downloaded unraid 6.9.2 - Copied contents over to USB - Made USB Bootable - Copied back up (from Mar 2021) super.dat and new key file over to USB - Array started and new messages beside my drives, please see screenshot Did what JorgeB said and ran the following command in the terminal... fdisk -l /dev/sdf [/quote] Here are the results for SDF root@Tower:~# fdisk -l /dev/sdf Disk /dev/sdf: 2.73 TiB, 3000592982016 bytes, 5860533168 sectors Disk model: WDC WD30EZRX-00D Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disklabel type: gpt Disk identifier: EE820A84-8CBB-49CC-A1D1-1EBAE7AC7DD6 Device Start End Sectors Size Type /dev/sdf1 64 5860533134 5860533071 2.7T Linux filesystem root@Tower:~# Tried another drive SDE root@Tower:~# fdisk -l /dev/sde Disk /dev/sde: 5.46 TiB, 6001175126016 bytes, 11721045168 sectors Disk model: WDC WD60EFRX-68L Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes root@Tower:~# Is there anything that can be done or am I looking at starting over?

I started using BinHex Minecraft Bedrock docker and there was 3 ports recommended in the forums, 19xxx and 2 others with the same first 2 digits. I've never opened ports up to my server before and now this happened within a few weeks after. It's only precautionary but i've been living at this new place and the ISPs router they give you is not the most secure. I also read a post on the support forums of someone leaving 2 ports opened and they may have been hacked/erased all thier data which is beginning to sound like what happened to me. I know unraid uses 443 and 80 and that shouldn't be opened. I'm still trying to figure out how 2 different USB drives are both blank, one I just reformatted and installed 2 weeks ago.

I plugged in my new flashdrive to Windows I created about 2 weeks ago and it's blank. I tried going into the flashdrive thru the cmd prompt and there's nothing there. Both windows and the cmd prompt say there is 30mb being used on on the flash drive. This will be the 2nd time i've tried reinstalling the flash drive and i'm beginning to think my system has been compromised because that's 2 USB Flash drives that have gone blank. I have unplugged the network cable from my unraid system and reset/erased all the portforwarding for my unraid system on the new router I have. I've been reading about replacing the flash drive (again). Once I create a new flash drive, do i just copy over the super.dat file and key file from my backup I made in March of this year?

No, my system was running great until 2 weeks ago (or when I started this thread).

I have a back up I did of my system from March of this year. Should I just copy it over to the USB drive?

I hooked up a monitor and keyboard and when booting I get this error... CMOS Fail, press Del to setup I loaded the last good config and it seemed to bypass this screen. Then after a few minutes I get this screen... Syslinux 6.03 EDD 2014-10-06 Copyright (c) 1984-2014 H. Peter Anvin et Al Failed to load ldlinux.c32 boot failed: please change disks and press a key to continue. Help please..

I had to force shut down the server last night. I just tried starting it and i still can't log in... When i try accessing the webGUI it says connection took too long, ERR_Connection_Time_Out When I try pinging the server it says destination host not available When I try using Putty - COnnection timed out I looked at my router settings and the server is no longer listed there. I will try to get another monitor (or use this one) and find a keyboard to plug into the server and see if I can see anything that way. I'll also see if I can find an updated switch to increase transfer speeds. Is there anything I can do to start troubleshooting? At this point, what are the chances of my data being still there?

I'm not sure what is going on now. I installed Putty and tried logging into my server and nothing happened, tried a few minutes later and it's now timing out. I tried pinging the IP from the cmd line and now it's timing out. I checked my router to see what's active on the network and it's no longer listed.

I tried logging into my server to start the fdisk command but now i'm getting a 502 Bad Gateway error and can't access the web gui. I can ping the server and it's fine.

I can't seem to mount the disk that I unassigned. When I click on the orange mount button it says "mounting" for just a second then goes back to "Mount". Attached are a screen shot and diagnostics. Any help would be appreciated. tower-diagnostics-20210531-1922.zip

Yes the switch i'm using is close to 10years old. With RL and stuff going on right now, it's on the upgrade list. 100mb is good enough for just me at this time. I realized the IP/DNS settings are different on this new router i'm using (Switching ISPs still suck). I managed to get connected to Github and am now downloading the UD plug in.

When I try to install the UD plug-in by entering the URL it says network failure, when I go to the Apps page it says Community applications require internet access, etc I checked over the dns settings and they are set to what is suggested.

Yes it was completed and a parity check was done automatically with no errors.

My apologies for not understanding what you meant. I'll ask if I'm not sure next time. When I try running the files stem check im still getting the same error message On the main page the drive now says "unmountable, not mounted"

Trying out your first suggestion... I unassigned the first disk restarted the arrray added the first disk again restarted the array The first disk now has a warning icon, "Device Contents Emulated" and it says "Unmountable: Not Mounted" it also says "Stop is disabled - Parity operation is running" Hopefully this is good news!

Hello all, After 9 years I had my first system issue with UnRaid... A few days ago my USB drive died and I couldn't start the array so I followed the instructions found on the wiki and replaced the USB drive and key, now i'm getting these errors on my drives. "unmountable, unsupported partition layout" I tried running the "reiserfsck" command in the GUI and terminal but got this message... reiserfsck 3.6.27 Will read-only check consistency of the filesystem on /dev/md1 Will put log info to 'stdout' Failed to open the device '/dev/md1': Unknown code er3k 127 I was planning to get a new HDD this month to switch over to XSF system but this little surprise happened. I haven't done any formatting and would hopefully like to keep all the data on my drives. From what is says on the Main page, Parity is valid. Diagnostic file has been attached. Any help would be greatly appreciated. Thank you tower-diagnostics-20210526-1956.zip

Hey everyone, Can someone check over my new WD Red 6tb drive preclear results? With my basic understanding of the script from it's original post, everything seems ok. Thanks in advance! ================================================================== 1.15 = unRAID server Pre-Clear disk /dev/sdc = cycle 1 of 1, partition start on sector 1 = Disk Pre-Clear-Read completed DONE = Step 1 of 10 - Copying zeros to first 2048k bytes DONE = Step 2 of 10 - Copying zeros to remainder of disk to clear it DONE = Step 3 of 10 - Disk is now cleared from MBR onward. DONE = Step 4 of 10 - Clearing MBR bytes for partition 2,3 & 4 DONE = Step 5 of 10 - Clearing MBR code area DONE = Step 6 of 10 - Setting MBR signature bytes DONE = Step 7 of 10 - Setting partition 1 to precleared state DONE = Step 8 of 10 - Notifying kernel we changed the partitioning DONE = Step 9 of 10 - Creating the /dev/disk/by* entries DONE = Step 10 of 10 - Verifying if the MBR is cleared. DONE = Disk Post-Clear-Read completed DONE Disk Temperature: 37C, Elapsed Time: 54:48:31 ========================================================================1.15 == WDCWD60EFRX-68L0BN1 WD-WX11D65CU3Z1 == Disk /dev/sdc has been successfully precleared == with a starting sector of 1 ============================================================================ ** Changed attributes in files: /tmp/smart_start_sdc /tmp/smart_finish_sdc ATTRIBUTE NEW_VAL OLD_VAL FAILURE_THRESHOLD STATUS RAW_VALUE Seek_Error_Rate = 100 200 0 ok 0 Temperature_Celsius = 115 127 0 ok 37 No SMART attributes are FAILING_NOW 0 sectors were pending re-allocation before the start of the preclear. 0 sectors were pending re-allocation after pre-read in cycle 1 of 1. 0 sectors were pending re-allocation after zero of disk in cycle 1 of 1. 0 sectors are pending re-allocation at the end of the preclear, the number of sectors pending re-allocation did not change. 0 sectors had been re-allocated before the start of the preclear. 0 sectors are re-allocated at the end of the preclear, the number of sectors re-allocated did not change.

Are these cards still for sale and would you be willing to skip to Canada?

Any chance you would be willing to ship to Canada?