Ryanoc3ros

I have disabled all VMs and will monitor the system for a day or so. Assuming it is a VM issue, is it recommended to recreate the VM from scratch? Or will that not affect much?

I recently upgraded my server to a ASrock Z690 Extreme MB and Intel i5-13500 CPU. Since upgrading I have had numerous crashes after anywhere from 30 minutes to 9 hours. I have been running "stress" as a way to tax the system and bring out any instability. Below are my notes on all of the actions I have taken. Jun 21 19:02 Startup Jun 21 19:39 Crash (uptime 37 minutes). Crashed around the time I unplugged Z-wave stick and restarted Home Assistant VM Last log entries before crash: Jun 21 19:39:33 Snorlax kernel: docker0: port 5(veth5aa8f3e) entered disabled state Jun 21 19:39:33 Snorlax kernel: veth4dd9902: renamed from eth0 Jun 21 19:39:33 Snorlax kernel: docker0: port 5(veth5aa8f3e) entered disabled state Jun 21 19:39:33 Snorlax kernel: device veth5aa8f3e left promiscuous mode Jun 21 19:39:33 Snorlax kernel: docker0: port 5(veth5aa8f3e) entered disabled state Jun 21 19:39:34 Snorlax kernel: docker0: port 5(veth8079aaf) entered blocking state Jun 21 19:39:34 Snorlax kernel: docker0: port 5(veth8079aaf) entered disabled state Jun 21 19:39:34 Snorlax kernel: device veth8079aaf entered promiscuous mode Jun 21 19:39:34 Snorlax kernel: docker0: port 5(veth8079aaf) entered blocking state Jun 21 19:39:34 Snorlax kernel: docker0: port 5(veth8079aaf) entered forwarding state Jun 21 19:39:34 Snorlax kernel: eth0: renamed from vetha164b17 Jun 21 19:39:34 Snorlax kernel: IPv6: ADDRCONF(NETDEV_CHANGE): veth8079aaf: link becomes ready Jun 21 19:45 Ran Memtest86, Passed no errors Jun 21 20:20 Startup Jun 21 20:30 Disk 1 had several SMART errors, it is an old hard drive, so as a precaution, I started moving files from disk 1 to other disks with Unbalance Jun 22 05:42 Crash (uptime 9 hours) Last log entries before crash: Jun 22 05:42:30 Snorlax kernel: usb 2-8.4: Device not responding to setup address. Jun 22 05:42:30 Snorlax kernel: usb 2-8.4: Device not responding to setup address. Jun 22 05:42:31 Snorlax kernel: usb 2-8.4: device not accepting address 3, error -71 Jun 22 05:42:31 Snorlax kernel: usb 2-8.4: reset SuperSpeed USB device number 3 using xhci_hcd Jun 22 05:42:31 Snorlax kernel: usb 2-8.4: LPM exit latency is zeroed, disabling LPM. Below is my log of everything I have done today (June 22). There is something noteworthy at "Jun 22 13:13" in the syslogs. *10:23 Startup 11:45 Manual Shutdown 11:50 BIOS Updates: Turned off CPU C-States Set "Restore on AC Power Loss" to "Power On" Disabled HD Audio Long Duration Power Limit changed from Auto to 125 (not sure why) 11:50 Removed USB Coral, Z-Wave dongle, Zigbee Dongle, left USB drive in 3.0 slot *11:55 Startup 12:00 Set Frigate to use CPU detector 12:00 Ran CPU stress test starting at 12:00 13:13 Kernel Panic? Didn't lock up entire system 13:13 Home Assistant locks up 13:15 Stopped stress test 13:15 Restarted HA 13:15 Continued to run stress test *16:06 Crash (uptime 4 hours) 16:35 Restart and quick crash 16:45 Move USB Flash from USB 3 port to USB 2 port 16:46 Startup and run stress test 21:15 Turned off Pi-Hole Docker *21:52 Crash (uptime 5 hours) *22:16 Startup in GUI mode so I can watch directly attached monitor 22:19 Shutdown all dockers 22:24 Disabled Docker 22:30 Removed several plugins 22:32 Started stress test *23:30 Crash, monitor glitching and flashing rapidly Any help would be greatly appreciated. Thank you. syslog-10.0.0.13.log snorlax-diagnostics-20240622-2338.zip

Found the solution on reddit. Due to the recent change in the authentication process, using your email and password for the manual connection method will no longer work. You will need to use the service credentials instead. You can find your service credentials by following these steps: Please log in to your Nord Account by following this link: https://my.nordaccount.com/dashboard/nordvpn/ Click on the NordVPN tab on the left panel which is under the Services tab. Scroll down and locate the Manual Setup tab, then click on Set up NordVPN manually: Verify your email by entering the one-time code you will receive in your registered email inbox. If you are unable to find the email, please make sure to also check your spam/junk folder. Copy your service credentials by using the buttons on the right.

I am having issues getting my DelugeVPN container to start. Everything worked fine until early today. I have done no updates or configuration changes that might break something. I am still running Unraid 6.11.5. I have attached my log file. After the initial startup it just continues in a loop trying the connect to NordVPN. I've tried changing my user/pass, and confirmed it is correct. I also tried different NordVPN .ovpn files, but nothing works. Is there something I am missing? supervisord.log