ashkasto

Thank you!! Looks like there was a bad splitter for power to one of the sata drives. I rebuilt drive in maintainance mode and now back up and running. Very much appreciate your help!

Thank you, let me check the power supply or cables, I left the SMART Test for the Extended Self test and came back to "Interrupted (host reset)" error, could not complete the extended smart test. Could that be from power cable issue as well? Unconfirmed 332964.crdownload

Greetings I recently noticed that my disk 3 has a error "device is disabled, contents emulated" I looked up and read...So i stoped the array, unassigned the disabled disk from partition and started array again, then stoped array again, then reassigned the disk to same slot and started maintenance mode and iniated sync. Shortly after initiating sync, the sync paused and same error showed up next to my disk 3, at that time under error colum i noticed 1024 as errors as well. So does this mean my drive is bad? I have attached a diagnostic and smart quick test. I am doing the extended test right now also. Thank you for any help or advice ashlab-smart-20251203-2216.zip Unconfirmed 156632.crdownload ashlab-smart-20251203-2122.zip

can Anyone help with this please?

This is the syslog after the server stop responding and screenshot on unraid screen with error, unable to access usb drive. Do I need a new USB drive? syslog-192.168.12.9.log

How and where do I do that on my server? Thank you ...nvm I turned on the sys log to save on my casche drive...hope to catch what is happening

Recently I have encountered an issue where the unraid server stops working after starting the server. It can be in 24hr or a few days. It happened once in a week or two now more frequent. I must power down the server with power button and reload server and things work and then same cycle occurs hours to days later. I can not access the GUI sometimes at all and the docker apps load but do not work. I have included the diagnotic file when it loads back up. This last time it loaded up but was not working correctly and the diagnotic file would not download. Can any help explain what is going on and what I can do to fix it? Thank You ashlab-diagnostics-20250801-0944.zip

It turned out that I had a lot of orphan images that needed to be removed by clicking the advanced tab. I wish I knew that before making my docker vdisk larger.

I have unraid OS plus, Does that allow 12 drives per license? If I want to upgrade to unlimited drives what are my options? Now the subscriptions do not offer lifetime software upgrades? If so why not? thank You

I would appreciate any clarification on this topic in more detail My image file size is set to 27Gb, because I increased it, I am also aware that now I can not make a smaller img file without deleting all my docker applications and starting from scratch (which is so much time I put is setting my dockers up I don't want to do unless I can save my docker setting and reload them.). On looking at container size I do not use that much space says 8.46 GB if I am understanding this correct. So not sure why the system section says I have 84% utilization Appreciate anyone's knowledge about this subject. Unconfirmed 998744.crdownload

why does it state system memory? I am a bit confused what this means. Can you help direct me where I can get more info what this means? Also, is the fact that it is in the RED a bad thing? How do I resolve it if it is? The fix common problems keeps showing I have limited space... see screen shot

Hello I would appreciate assistance in finding out what docker instance could be causing me a problem. My RAM is fully utilized by docker for some reason. I have attached diagnostics Thank you Unconfirmed 204250.crdownload

it has transcoded before but never had such a load reported. with the i9 12900k one transcode should not place 75-80 percent load

Hoping someone can explain why I have such high CPU load on the server. Today came home and noticed it was running very high. Docker was not loading and was unable to stop array. I tried reboot and would not load and received a bzfirmware error and replaced all bz* files on my usb drive and reloaded the system. It is running okay but still getting these very high loads for not much going on. I included a diagnostic file. Thank you for any help Unconfirmed 630986.crdownload

Got it, thank you