bohaman

I will give it a try. THank you for your suggestion

I apologize I think I had mover logging enabled so it may not be annonymous. Please let me know if i need to remove anything for privacy. Thank you for your help

I'm new to Unraid and hope if someone can help me troubleshoot this problem. I have an Array, and two SSD cache drives. When I transfer files from my PC to unraid the files stay at cache drive then at 3am I have schedule it move to my Array. My current network is 10GB/s. My speed when transfer into unraid is good and constant thanks to the cache drives. However, when I transfer my files from unraid to my PC a certain files and certain folders have really slow speed I'm talking about 20MBs instead of regular 200-280MBs. Even the files within the same folders somes have really slow speed transfer. I've checked and those files are currently storing in the same disk of the array. I'm not sure if I have set up something wrong and I hope someone could help me out. Thank you for reading.

Hello, Sorry for the late reply. I actually tried your suggestion and plugged in a different samsung 128gb usb flash drive and it worked. For some reason my samsung T7 doesn't recognized when plugged in to the 3.1 10gbs port. The other samsung flashdrive 128gb worked in USB 3.1 10gbs port. Do you think it maybe because of the cable I used? With the same motherboard when I run under windows OS it recognized so I don't think its the cable problem. My current mainboard is X99-E WS/USB 3.1 Thank you for your time in reading my post. Please let me know if you need any additional information.

Hello, when I plugged my USB drive to my USB 3.1 port unraid doesn't recognize the drive. but if I plugged it in my USB 3.0 or USB 2.0 unraid recognize the disk fine. Does any body have similar problem?

Hello, I am running into problem where my transfer speed doesn't get full speed after for about 30 seconds or so. I've tried to resolve it by some other post by disabling bond and bridge and connect directly from unraid 10gbe but it seems the problem still persist. I've attached my diagnostic log as well. tower-diagnostics-20231008-0936.zip

Hello, I am running into another problem and I hope I can get some guidance from someone. Issue: Handbreak froze encoding process everytime I am transfering files via SMB share drives from unraid. What I have tried: I looked CPU pinning and limited handbreak to only using certain cores and it worked as I see only cores I pinned handbreak uses. However when I tried to do files transfer via unraid SMB share drives the CPU dropped back down, handbreak stopped working. After the files transfer completed, handbreak start again and all the pinned cpu ran again. My system is currently E5-2687W v4 and leave 4 cpu cores unchecked from pinning but unraid still pause handbreak and resume after files transfer. I've looked up on google and found that I can set cpu priority for docker container so I tried --cpu-shares=10240 in the extra parimeters for handbreak container but it still doesn't give prioritize for handbreak. I've also looked up cpu isolation but that only applicable to VM only? Thank you all for your time.

I apologize for my unclear question. I'm not sure what to provide. I have shares smb with log-in and password. I can access it via windows PC. I was hoping to allow handbreak running unraid as a docker container to export its transcoded files to the already "shared" folder smb so I don't have to transfer it over to access it from my PC after handbreak finished. The transcode taking place source is from "input folder" which is shared via SMB. I copy files from my PC and put it there. Then in handbreak I chose the input folder (which unraid can access). However when I sent export destination to and choose my output folder shared via SMB it doesn't have permission. The transcoding happining within Unraid server as handbreak is running as a docker container. However I think even though the allowed destination for me to export the file default is "output" in handbreak. I went to the setting and change the default destination to my SMB shared drives and I think it worked. I am not sure how, but I think it worked. Thank you for all of your help.

Hello, I am new to unraid and I hope if someone could help guide me to the right direction. When I tried to output unraid to my SMB share it said that I don't have permission to read or write. May I ask if anyone can guide me on how to add permission to unraid so that it can output converted files to my SMB share drives? If it is not possible, may I ask on how do I share the output files from handbrake transcoded files so that I can access on my PC? Thank you so much for your time.