ramjam824

100%, run in test mode, plug-in filters set to YES, and select options you feel align with what you are seeking as output. Keep tinkering until you see the output match your expectations. Then, turn test mode off and let it rip!

Good luck, I hope the move goes smoothly!

Hey @EDACerton, I am having issues with switching from the docker -> plugin. I feel like I have tried everything in this thread but I still cannot see my server in File Explorer (Network Tab) I cannot add via 'Add Network Location' (\\servername\sharename or tailscaleIP\sharename) I can view the Unraid web GUI and I can access my dockers via Tailscale IP:docker ID I included the diag zip here. Please let me know what else you may need to assist in resolving my issue RamJam-tailscale-diag-20240812-185801.zip

Looks like it's working now. Will let this run overnight and report back in the morning! Thank you @Reynald

@Reynald Still not working for me.

Can't seem to get this working with Unraid 7.0.0 beta 2 and my ZFS hard drive pool. any support would be great!

Does this network path sound right? FIOS ONT -> Fios Router -> Ethernet Switch (what kind of switch for a 10gbe network?) -> Run Cables

With that being the case, what can I do to improve the situation?

~1gbps in -R

I don't have the capability to test with all devices wired.

iperf3 = ~430 Mbits/sec for sender and receiver (going to purchase a new cat 6 cable today) HDD speed. But, my user share config for data is Cache -> Spinners. My Cache is 4TB (2x 2TB nvme drive) and is 5% full. I just ran a speed test now from my laptop (wireless connection to my Fios router)

I cannot figure out how to improve SMB performance, please help, any support will be greatly appreciated. Thank you! Home Networking Setup Verizon Fios 1 GB/s Unraid server connected to 10GBE LAN port on the Fios router Server NIC: 10Gb PCI-E NIC Network Card, Dual Copper RJ45 Port, with Intel X550-AT2 Controller Windows 11 Laptop connecting wirelessly to Unraid Torrent download speed ~140mb/s Unraid Build Unraid OS: 7.0.0-beta.2 M/B: Supermicro H12SSL-i Version 1.10 s/n ZM243S602309 BIOS: American Megatrends Inc. Version 2.7 Dated 10/25/2023 CPU: AMD EPYC 7402 24-Core @ 2800 MHz Memory: 128 GiB DDR4 Multi-bit ECC (max. installable capacity 2048 GiB) Network: bond0: fault-tolerance (active-backup), mtu 1500 Pool Setup Cache Pool: ZFS, Raid 0, Striped NVME Cache HDD Pool: ZFS, Raid Z1, 6 Drives w/ SSD L2 Cache as a sub-pool SMB Issues Poor read/write performance Windows -> Unraid = ~15mbps Unraid -> Windows = ~30mbps I cannot change MTU = 9000 on the FIOS router, I tried to do so but only accepts a value <= 1500 within the FIOS router GUI. I have enabled the following settings:

I am running Mover from Main -> Move right now. I was unsuccessful invoking Mover with, Plug-in Filters = Yes and Test Mode = No. I am watching the Cache Pool used reduce in size and my Spinners Pool used increase in size. This means to me that Mover is working, correct? However, I did have my "Only move at this threshold of used cache space: " 50%. My cache pool was less than 50% utilized so this may have been the reason why Mover did not execute. I will lower the setting and fill up my cache pool + rerun with your suggested settings. FYI - I am very new to Unraid and home lab/server stuff. Just started this journey a few days ago

@Reynald I am on Unraid 7.0.0-beta.2 and want to say thank you for the continued work on CA Mover Tuning. I have done the following: Removed the prior version Installed the forked version via your link posted on this thread, I think on page 60 or so Move Now button follows plug-in filters: NO Test Mode: YES Now to confirm: Mover will not run on schedule I have manually invoked Mover on Main -> Move (which thanks to you + other folks, is working now!) Is there anything else I need to do for now?