• Posts

  • Joined

  • Last visited

Everything posted by Tiller

  1. I had the same issue. I updated and then the web UI would no longer load. Tried to restart the container a couple times but nothing changed. I rolled back to the previous version and it loads just fine, so I'm not sure what the issue was.
  2. I hooked up a keyboard and monitor while the server was still on, but the display said there was no signal. So I couldn't even attempt to enter any commands. One second push of the power button didn't do anything, so I held to force the shutdown. I turned the server back on. So far, it seems like it has booted up normally. Like you said, it was an unclean shutdown so another parity check will be required when I start the array. Which I won't do yet until someone can look over the attached diagnostics and I can see if I will just have the same problem again. When I booted up, there was a notification saying the parity check ended at around 4 hours with 0 errors. But obviously it didn't actually finish in that short of a time span and when it says it ended is when I lost connection with the server last night. Like I said, I've attached the diagnostics. I also went ahead and made a new backup of the flash drive with the hope that the config directory is good at least. We'll see. tower-diagnostics-20211012-1956.zip
  3. I was out of town over the weekend and at some point a power outage happened at the house. It must have lasted long enough that my battery backup also went down because I came home to the Main Menu screen in the Web UI saying there had been an unclean shutdown and when I started the array then a parity check would be performed. Okay, fine, no problem. About four or five hours into the parity check, I lost connection to the server. I can't view any share folders through Windows trying to view a network location. I can't connect to the Web UI. Pinging tells me the destination host is unreachable. I left it alone overnight in the hopes that somehow the parity check was still going on and maybe it would allow me to connect when it finished. That was over 24 hours ago, and for my system the check usually takes about 18 hours. Still can't connect and pinging gives me nothing even though the server is still powered on. After some Google searches, I am worried maybe my flash drive is failing or has failed but I'm not sure how to check it. Should I just press the power button on my server to force a shutdown and then try plugging the flash drive into my Windows PC? Or am I way off base and is there something else I should try or check first? Any help or guidance would be appreciated. Thanks in advance.
  4. I've been having some weird issues with QBittorrent. Over the past month or so, when I add a new torrent it just goes straight to the Errored state. If I delete the perms file and restart the Docker, then it works fine for a day or so. Well now today the Docker won't restart. I keep getting this message in the logs: 2021-05-19 17:07:03,545 DEBG 'start-script' stdout output: [warn] Unable to successfully download PIA json to generate token from URL 'https://privateinternetaccess.com/gtoken/generateToken' [info] 12 retries left [info] Retrying in 10 secs... I have tried changing the OpenVPN endpoint file to like five or six different countries, something that has sometimes helped in the past, but it's still not working. Anyone have any ideas on what could be the issue?
  5. Thanks for the quick reply. You helped me solve it -- I had to add the leading "/" and change "Downloads" to "data".
  6. I'm having an issue. In the configuration, I set my /data folder to be the location I have been using for downloads with qBittorrent (which I have no issues with). See the image. However, when I download something in SABnzbd, it goes to a download folder in the /config location. I'm not sure why it's ignoring my selected /data setting. And I can see in the Folders section of the Config in the application that it's using /config as the base folder location. So what can I do to get it to download to the correct location? Thanks in advance.
  7. Awesome, thanks for the quick reply. I did a quick search on Amazon and I found these. Does that look like it would work? The description says it has already been flashed to IT MODE and the seller appears to be based out of Maryland.
  8. Can anyone please give me a recommendation on controller cards to replace my current ones? I have the warning in the Fix Common Problems plugin about having Marvel-based hard drive controllers. I would like to replace them before I start encountering any serious issues. I wasn't aware of the problem with Marvel controllers when I did the build (and honestly I just copied the components from another server I found on PCPartPicker). For reference: I have the Supermicro X9DR3-F as my motherboard and my current controllers are two of the Supermicro AOC-SAS2LP-MV8 cards. The cables I bought to connect the controllers to my drives can be seen here. With this in mind, what is a good card you can recommend that I can buy two of and just plug into my current system without any issues? Thanks in advance for your help.
  9. So I am an idiot and I need some help. I was trying to copy an executable JAR file from Windows to my appdata folder to try and create a new server (appdata/minecraft/servers/[server_name] specifically) but I kept getting a permission denied error. After some searching I found someone who said they had a permissions problem solved by running a script that changed permissions for every directory in appdata, so I took a line from the script and modified it to just affect the minecraft directory (chmod -cR ug+rw,ug+X,o-rwx minecraft). It finished running but it didn't change my ability to copy files. Now, however, everything for Minecraft is broken. I cannot connect to or even start servers that were previously working. I've attached my diagnostics -- don't know if that will help. Is there any way to fix my permissions so that first my existing servers will work again and then second so that I can copy files from Windows without permissions issues? Any help would be appreciated. Thanks. tower-diagnostics-20200402-1231.zip
  10. I'm hoping to get some help on an issue I just started having. I seem to be having some permissions issues that randomly started happening. Everything was working fine -- and has for a long time -- but now whenever a torrent is added to the download client it starts to download, shows that I'm connected to peers, and the download speed will start increasing. But the percentage done stays at 0% and the speed will go to 0 and stall. This happens for torrents added manually as well as those from Sonarr and Radarr. The logs show a bunch of I/O errors and failure to moves due to permissions being denied. But like I said, this just started happening and I haven't changed any settings in any dockers or in unRAID. I've restarted the docker, rebooted the unRAID server, tried to force recheck the torrents and none of it will get the torrents to actually start downloading. I just keep getting the permission denied messages. It was working last night before I went to sleep, so I don't know what's going on. The only thing I can think of that happened over night is the Mover invoking and moving files from my cache. Any help for this issue would be appreciated. Thanks in advance.
  11. Hoping I could get some help. I've been using DelugeVPN for like a year with no issues. Yesterday I stopped every docker container except for Plex and I performed a parity check. Everything seemed to go fine -- found 5 errors that were corrected. When I restarted the rest of my containers (DelugeVPN, Sonarr, Radarr, and Jackett) they all started without issue. However, when Sonarr found new downloads and loaded them into DelugeVPN they immediately went to the "Error" status and won't download. I tried manually adding a torrent via a magnet link and downloading the .torrent file first and the same thing happened. When I go to the Details tab in Deluge, the Status of the torrent says "Permission denied: /data/Incomplete/[file name]". I did not change any settings in Deluge after the parity check, and the paths all look the same as they did before the parity check when everything worked fine. Does anyone know what I can do to fix this issue? I'm not sure exactly how to proceed. So any help would be appreciated.
  12. ...huh. That worked. Why did that work? I don't remember having any issues in earlier versions of unRAID and I've been running uBlock Origin for forever. Anyway, thanks so much for the quick reply.
  13. Hey, all. I just updated from unRAID version 6.3 to 6.5. I also updated a couple of plugins. The OS update required a reboot, so I did it. Once I had restarted my array, I noticed that my user share (just named "Media") had disappeared. I haven't checked in a while, so I don't know if it disappeared after the update and reboot or before today, but it's definitely gone now. I can still access the location via my Windows File Explorer as a network location. It just shows that I have no shares in the unRAID web UI. I have a Docker for Deluge and the downloads folder points to a location in the "Media" folder. I downloaded something before I noticed the share was missing and it finished downloading and appeared in the folder like normal. Since my share has disappeared, though, I don't know if files will be distributed correctly among the disks in my array. I have already stopped and started the array as well as trying to reboot the server twice now. Any ideas what caused the share to disappear? How can I get it back? What would happen if I just add a share that has the same name as the old one? I've attached my zipped diagnostics file. If anyone can help, I'd appreciate it. Thanks. tower-diagnostics-20180828-1827.zip
  14. I am currently performing the parity check. All of the files in the lost+found folder seem to be 0 byte files with numbers as names. How am I supposed to interpret that? There are about 25 of them.
  15. So it finished and I was able to start the array. Are there any steps I need to do now? A parity check? The only difference I noticed was a new share called "lost+found". Is there anything I need to do involving that?
  16. Okay, I'll run it and report back. Thanks again for all the help, everyone.
  17. Okay. I found it. Thanks. However, it is giving me the same error message I replied with before about using the -L option. So do I just go ahead and do that or are there any other things I should try since it says the -L option may cause corruption?
  18. This is what I get when trying it. Do I use the -L option?
  19. Okay, I'll give that a shot and see how it goes. Thanks for the help.
  20. Here's the zip resulting from the diagnostics command. tower-diagnostics-20180113-1350.zip
  21. I recently built a new server as an upgrade to my old rig. I had already transferred over all my old drives and did a parity check and everything was fine. I added a new data drive and a cache drive and everything has been working fine for a few days. Today, another new data drive finished pre-clearing and I tried to stop the array to add the new drive. For some reason, the stopping of the array got hung up, I believe on "Unmounting disks..." I couldn't get anything to change its status, so I powered down the server. Now when I power it back up and get back to the webGUI (where all drives are detected as in "Normal operation"), I click the "Start" button to start the array and perform a parity check. However, just like when I tried to stop it, it's now stuck on "Mounting disks..." I'm pretty new to all of this and the command line, so I'm not sure what to do to troubleshoot this and get everything working again. If someone could give me some guidance, it would be greatly appreciated.
  22. I know that the device drive limit for a Basic License in unRAID V6 is 6 hard drives. I currently have 5 drives in my array -- 1 parity and 4 data. If I buy a 6th drive, does it have to be used as a cache drive or can I use it as a 5th data drive?
  23. Hey, guys. I'm wondering if anyone can come up with some idea as to what's going on with my setup. I just bought a new router -- Netgear Nighthawk AC1900. I used to have an old Belkin router. Anyway, I didn't change the way things are arranged. I have my modem plugged into the router, and the router plugged into a gigabit switch. My server is also connected to the switch. Whenever I transfer files to the server, I plug an ethernet cable into my laptop from the switch. Before I changed routers, my transfer speed was usually around 30 MB/s. For some reason, after the switch my speeds are only at about 3 or 4 MB/s. Like I said, I didn't change anything about the setup. Just unplugged one router and plugged in the new one. I tried making sure that the ethernet local connection was prioritized over the wireless one, but it didn't change anything. At one point I unplugged the switch and changed the ports I was using, and it went back up to 30. But then about 20 minutes later it reverted to the slow speeds and I hadn't touched or changed anything. So if anyone has any ideas for things to troubleshoot or what the issue is, I'd appreciate it.