djdexter

anyone?

I got the emptdd to stop but my docker still doesn't start Docker Service failed to start. new data attached djdexter.ath.cx-diagnostics-20180514-0102.zip

my docker fails to load all of sudden and i'm getting this error May 14 00:45:47 djdexter emhttpd: error: put_config_idx, 609: Invalid argument (22): fopen: /boot/config/shares/"TV Shows".cfg I have been using unraid and docker for years now all of a sudden today it does this I have included my zip file etc Docker Service failed to start. djdexter.ath.cx-diagnostics-20180514-0044.zip syslog.txt docker.txt disk.cfg docker.cfg domain.cfg flash.cfg go ident.cfg network.cfg share.cfg smart-one.cfg super.dat

so i did a few reboots in the hope that the drive would magically be undisabled. nope so i currently did a new config, your right in your description and my parity must have been valid and i might have confused it with a parity sync check or something. either way i'm way too far in the deep in now, i'm doing a new config and 5 hours left to completion. i just hope i didn't lose any old data another question how do i know if my power supply is adequeate for the number of drives i have. does unraid have a built in thing that says low power supply

see attached zip.zip

i stopped array added new disk and it never completed the new parity. i vaguely remember it saying error code -5 i was doing a parity check on the system with the new drive when the drive 1 came up red

reiserfsck 3.6.24 Will read-only check consistency of the filesystem on /dev/md1 Will put log info to 'stdout' ########### reiserfsck --check started at Sat Dec 3 11:10:01 2016 ########### Replaying journal: Replaying journal: Done. Reiserfs journal '/dev/md1' in blocks [18..8211]: 0 transactions replayed Checking internal tree.. finished Comparing bitmaps..finished Checking Semantic tree: finished No corruptions found There are on the filesystem: Leaves 476077 Internal nodes 2945 Directories 10572 Other files 36621 Data block pointers 476448905 (0 of them are zero) Safe links 0 ########### reiserfsck finished at Sat Dec 3 13:53:44 2016 ###########

i used the one built in to unraid 6.1 syslog.txt

Firstly nothing was being written to the disk problem i had added a new harddrive to my array the other day and not sure if the parity was valid for new hardrive. disk 1 went faulty. checked smart reports etc the disk is fine. i ran resesfs check came back clean. would you A. do the new config and hope its all good B. do the re enable procedure knowing that your parity might not have been valid since you added that new hardrive to array?

that is why i love this community, such good people and answers, i will try both recommendations tonight

here is my system log, my cache keeps going to unassigned devices and then i can't mount it. it is btfrs? syslog.txt

i'm using iterm on mac. is that what you mean

running unraid 6.1.x so I went to my flash drive /boot/config and deleted my ssh keys now i can't ssh in (need it for plex setup) a a completed noob and don't know much What exactly do i do? @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ @ WARNING: REMOTE HOST IDENTIFICATION HAS CHANGED! @ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ IT IS POSSIBLE THAT SOMEONE IS DOING SOMETHING NASTY! Someone could be eavesdropping on you right now (man-in-the-middle attack)! It is also possible that a host key has just been changed. The fingerprint for the ECDSA key sent by the remote host is SHA256:xJmDQvyokKlFZONlHSUeqhLUrL7rGspi63el0BoOmso. Please contact your system administrator. Add correct host key in /Users/Amit/.ssh/known_hosts to get rid of this message. Offending ECDSA key in /Users/Amit/.ssh/known_hosts:1 ECDSA host key for 192.170.1.77 has changed and you have requested strict checking. Host key verification failed.

solved i did ssh and it worked!

i'm stumped here please help. i had plex running great HAD being the key word until i went into my plex and accidently deleted my server. so then I deleted plex appdata from my cache /mnt/cache/appdata/plex resinstalled the docker now in my plex the server still won't show up. What am i doing wrong? I will donate if you can help me get it working ##################################################### # Login via the webui at http://<ip>:32400/web # # and restart the docker, because there was no # # plex token found in the preference file # ##################################################### [cont-init.d] 50-plex-update: exited 0. [cont-init.d] done. [services.d] starting services Starting dbus-daemon Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited [services.d] done. Starting Avahi daemon Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support unlimited Starting Plex Media Server. 6 3000 /config/Library/Application Support