Quazeye

Okay.. thanks.

Hi, Okay here is the Smart Report. Thanks, Q Statistics for /dev/sda Hitachi_HDS723020BLA642_MN1221F300XA6A smartctl -a -d ata /dev/sda smartctl 6.2 2013-07-26 r3841 [i686-linux-3.9.11p-unRAID] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1221F300XA6A LU WWN Device Id: 5 000cca 369c06a58 Firmware Version: MN6OA180 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Sun Mar 18 14:57:27 2018 MDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (19523) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 326) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 65536 2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 85 3 Spin_Up_Time 0x0007 130 130 024 Pre-fail Always - 439 (Average 440) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1253 5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1905 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 133 133 020 Pre-fail Offline - 27 9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 59485 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 35 192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 1557 193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 1557 194 Temperature_Celsius 0x0002 253 253 000 Old_age Always - 22 (Min/Max 13/43) 196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2832 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 182 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 7055 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7055 occurred at disk power-on lifetime: 59092 hours (2462 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 fa 35 cb 39 0d Error: UNC 250 sectors at LBA = 0x0d39cb35 = 221891381 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 2f cb 39 e0 00 20:42:36.485 READ DMA EXT ef 10 02 00 00 00 a0 00 20:42:36.485 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 20:42:36.485 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 20:42:36.483 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 20:42:36.483 SET FEATURES [Set transfer mode] Error 7054 occurred at disk power-on lifetime: 59089 hours (2462 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 cb a4 ee c9 0c Error: UNC 203 sectors at LBA = 0x0cc9eea4 = 214560420 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 6f ee c9 e0 00 18:26:54.743 READ DMA EXT 25 00 00 6f ea c9 e0 00 18:26:39.236 READ DMA EXT 25 00 00 6f e6 c9 e0 00 18:26:26.463 READ DMA EXT 25 00 00 6f e2 c9 e0 00 18:26:11.644 READ DMA EXT ef 10 02 00 00 00 a0 00 18:26:11.644 SET FEATURES [Enable SATA feature] Error 7053 occurred at disk power-on lifetime: 59086 hours (2461 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 4d 72 6a 28 0b Error: UNC 77 sectors at LBA = 0x0b286a72 = 187198066 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 50 6f 6a 28 e0 00 14:40:16.903 READ DMA EXT 35 00 a0 bf 64 28 e0 00 14:40:16.893 WRITE DMA EXT e5 00 00 00 00 00 40 00 14:40:16.893 CHECK POWER MODE 35 00 d8 e7 60 28 e0 00 14:40:16.874 WRITE DMA EXT ef 10 02 00 00 00 a0 00 14:40:16.874 SET FEATURES [Enable SATA feature] Error 7052 occurred at disk power-on lifetime: 59086 hours (2461 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 67 6a 28 0b Error: UNC 8 sectors at LBA = 0x0b286a67 = 187198055 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 10 5f 6a 28 e0 00 14:39:55.857 READ DMA EXT ef 10 02 00 00 00 a0 00 14:39:55.857 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 14:39:55.857 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 14:39:55.855 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 14:39:55.854 SET FEATURES [Set transfer mode] Error 7051 occurred at disk power-on lifetime: 59086 hours (2461 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 d6 89 66 28 0b Error: UNC 214 sectors at LBA = 0x0b286689 = 187197065 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 00 5f 66 28 e0 00 14:39:29.628 READ DMA EXT ef 10 02 00 00 00 a0 00 14:39:29.628 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 00 14:39:29.628 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 00 14:39:29.626 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 14:39:29.625 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 59485 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

Hi Everyone, I have gotten errors for the first time in 4 or 5 years in my monthly parity check. It has listed 838751 errors in the parity disk error column in the unRAID 5.05 main menu area. I have pasted the log file to pastebin here https://pastebin.com/tyaxrkME Does anyone know what I should be doing now? I have basically set and forget for the last 4 or 5 years so am totally out of the loop on what I should do. Thanks for the help. Q

Thanks again.. I think I am understanding this now. Basically the split level 2 says that unraid has the OPTION to make a directory for Movies on Disk 1 and Disk 2. It has the OPTION to also put the Comedy directory on Disk 1 and Disk 2 under the Movies directory on Disk 1 and Disk 2. It can then put the "40 Year Old Virgin" on either Disk 1 OR Disk 2 but not both thus keeping what is in the "40 Year Old Virgin" directory on that same disk. Q

Thanks Peter... So just to get this straight in my head. If I choose level 2 (the Comedy Directory) that would mean that the Comedy Directory could be on any disk but the files/folders under the Comdey Directory (40 Year Old Virgin and any files/folders underneath it) would be on the same disk as the Comedy Directory? If I choose level 3 (40 Year Old Virgin Directory) that would mean that the 40 Year Old Virgin directory could be on any disk but the files/folder underneath (DVD structure or mpeg files) would reside on the same disk as the 40 Year Old Virgin directory? Thanks again, Q

Hi, Can you tell me if this is correct. Share is Movies (this would be level 0) Inside Movies I have a Comedy Directory (this would be level 1) Inside Comedy I have a Directory called 40 Year Old Virgin (this would be level 2) Inside 40 Year Old Virgin I have the movie files... either a DVD directory structure or mpeg files. (this would be level 3) If I want all the files/folders inside the 40 Year Old Virgin directory (the dvd structure or the mpeg files) to be on the same disk as the 40 Year Old Virgin Directory (which I want to be placed on any available disk) would I use split level 2? Thanks, Q