Hi,
Okay here is the Smart Report.
Thanks,
Q
Statistics for /dev/sda Hitachi_HDS723020BLA642_MN1221F300XA6A
smartctl -a -d ata /dev/sda
smartctl 6.2 2013-07-26 r3841 [i686-linux-3.9.11p-unRAID] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K3000
Device Model: Hitachi HDS723020BLA642
Serial Number: MN1221F300XA6A
LU WWN Device Id: 5 000cca 369c06a58
Firmware Version: MN6OA180
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sun Mar 18 14:57:27 2018 MDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (19523) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 326) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 65536
2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 85
3 Spin_Up_Time 0x0007 130 130 024 Pre-fail Always - 439 (Average 440)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1253
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1905
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 133 133 020 Pre-fail Offline - 27
9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 59485
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 35
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 1557
193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 1557
194 Temperature_Celsius 0x0002 253 253 000 Old_age Always - 22 (Min/Max 13/43)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2832
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 182
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 7055 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 7055 occurred at disk power-on lifetime: 59092 hours (2462 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 fa 35 cb 39 0d Error: UNC 250 sectors at LBA = 0x0d39cb35 = 221891381
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 2f cb 39 e0 00 20:42:36.485 READ DMA EXT
ef 10 02 00 00 00 a0 00 20:42:36.485 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 20:42:36.485 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 20:42:36.483 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 20:42:36.483 SET FEATURES [Set transfer mode]
Error 7054 occurred at disk power-on lifetime: 59089 hours (2462 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 cb a4 ee c9 0c Error: UNC 203 sectors at LBA = 0x0cc9eea4 = 214560420
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 6f ee c9 e0 00 18:26:54.743 READ DMA EXT
25 00 00 6f ea c9 e0 00 18:26:39.236 READ DMA EXT
25 00 00 6f e6 c9 e0 00 18:26:26.463 READ DMA EXT
25 00 00 6f e2 c9 e0 00 18:26:11.644 READ DMA EXT
ef 10 02 00 00 00 a0 00 18:26:11.644 SET FEATURES [Enable SATA feature]
Error 7053 occurred at disk power-on lifetime: 59086 hours (2461 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 4d 72 6a 28 0b Error: UNC 77 sectors at LBA = 0x0b286a72 = 187198066
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 50 6f 6a 28 e0 00 14:40:16.903 READ DMA EXT
35 00 a0 bf 64 28 e0 00 14:40:16.893 WRITE DMA EXT
e5 00 00 00 00 00 40 00 14:40:16.893 CHECK POWER MODE
35 00 d8 e7 60 28 e0 00 14:40:16.874 WRITE DMA EXT
ef 10 02 00 00 00 a0 00 14:40:16.874 SET FEATURES [Enable SATA feature]
Error 7052 occurred at disk power-on lifetime: 59086 hours (2461 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 67 6a 28 0b Error: UNC 8 sectors at LBA = 0x0b286a67 = 187198055
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 10 5f 6a 28 e0 00 14:39:55.857 READ DMA EXT
ef 10 02 00 00 00 a0 00 14:39:55.857 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 14:39:55.857 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 14:39:55.855 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 14:39:55.854 SET FEATURES [Set transfer mode]
Error 7051 occurred at disk power-on lifetime: 59086 hours (2461 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 d6 89 66 28 0b Error: UNC 214 sectors at LBA = 0x0b286689 = 187197065
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 5f 66 28 e0 00 14:39:29.628 READ DMA EXT
ef 10 02 00 00 00 a0 00 14:39:29.628 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 e0 00 14:39:29.628 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 14:39:29.626 IDENTIFY DEVICE
ef 03 42 00 00 00 a0 00 14:39:29.625 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 59485 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.