thisaone

I thought the above problem might be fixed with an update. Unfortunately I just applied the latest update and it still isn't working. Any ideas on how to fix this?

Hello, I have read through the posts about tv_grab_zz_sdjson_sqlite and think I may have a duplicate issue. I am trying to run the --manage-lineups for this grabber and fails with the error message below when also using debug mode. "Can't connect to json.schedulesdirect.org:443 (Try again)\n\nTry again at /usr/share/perl5/vendor_perl/LWP/Protocol/http.pm line 50, <STDIN> line 2.\n" Is this related or the same as the issue found here: I know that my password and SD are working because it worked when I installed XMLTV on an Ubuntu install. Any help on getting this working would be greatly appreciated.

Thank you for mentioning that plug in. I hadn't found it. I will look into it and maybe try it, but it does say fan control is only for X10/X11 motherboards. Mine is older. I know SM implemented more controls into later boards so I may not get the control I am looking for unless I upgrade, which isn't in the near future.

Hello, I have read a few posts and it seems that installing outside packages seems to be a bad idea. I have Nerdpack installed and it works great for the packages it has. I have an older Supermicro X8 motherboard. I have the fans set at optimal in the bios and it is okay, but I am attempting to get more control over the fans. The Dynamix system autofan in CA does not work, in fact the Dynamix system temp does not work either. I found a python script that goes a little deeper into the fan controller chip and looks like it will give me more control. It requires a couple of other packages though. specifically python-smbus and i2c-dev. I have not found prebuilt packages for those, but if I were to figure out how to build them for slackware do the experts think either one may cause problems? The page about the script is here: http://www.patrikdufresne.com/en/supermicro-x8-fan-control/ Thanks in advance for your help.

Okay, my apologies. I did do some reading, and think I read the posts you are talking about. I guess I didn't think they were the same since my dockers have an IP address on the same network as my real computers. I am learning and know just enough to get myself into trouble. Thank you for the prompt reply.

Hello , I have gotten this container set up a couple of times. Once it was with host networking. When I did that I could only access the Unraid GUI. I have now changed networking to its own IP. Now I can access every other computer and docker containers with their own IP, but not the Unraid IP, GUI or otherwise. Any ideas on what I should be looking at? Thanks.

Okay, thanks anyway. I have googled...a lot. I believe I have set it up correctly from what I have found. I will look for information on setting it up as a device.

As an update I have gotten a couple more of them to work by forcing the CAID shown on other channels on them. Some still dont work though. I am thinking that maybe they use a different CAID for some reason. Is there a way to view what the CAID is of a channel when I am streaming it?

Okay, that is entirely possible. There were a lot of instructions spread out for this device. I came up with the following: Enable devices in TVadapter tab. Set up automatic IPTV network using m3u file. Map muxes to services to channels. Since 92 out of 101 were working I figured I was good on the basic setup. Do you have a link to the method you are talking about with it as a device?

I dont have the HDHomerun software on this pc to connnect directly to the HDHromerun. I can check from my other pc later if needed. I can play the channel through the play link in the mux tab through VLC so I know it is working though. The service link is bad, but the mux link is good. Is there a way to use the mux link instead? The logs says no assigned adapters. Is there a way to manually assign the adapter to the channel?

Thanks for offering some help. Here are the screen shots you requested. I included one for the log window output too instead of typing it. On the services tab I did have to set hide to "none" since it says the parents are disabled. On the services tab it shows auto check disabled. I changed that in my attempts to get it working.

I have gotten a HDHomerun Prime working with schedules direct EPG; for the most part. However, there are 9 channels that do not work. When I originally ran "map all" on the services they were ignored. I then manually added the channels based on some reading and set the service they connect to. The muxes pages shows them as mapped. I have been reading/trying to find out how to fix them and have discovered a few things that might give clues as to what the problem is. 1. If i play the link from the muxes tab in VLC they work. If I play the link in VLC from the services tab they do not. I do however see and active connection in the status tab when played through the services tab even though there is no output to VLC. 2. I also noticed that all of these channels do not have the "Encrypted" checkbox filled on the services tab, all the other channels do. The above leads me to believe that I can get them to work, but I cannot figure out how. Does anyone have any ideas? I am not sure what additional data/info you might need so let me know and I will get it as soon as possible.