Troussdesoin

Hey Guys, I just had my pretty stable unraid setup crash and when i restarted it i had a machine check events in the fix common problems pluging Here is my diagnostic, any idea what happended? thanks syslog.txt

Perfect, i had to also change it back to Cache > Array to actually tell the mover to move it. It would not work without it. Thanks a lot guys.

Do i need to stop the array before doing that? or can i do it with everything running?

Alright, i want the 396 Gb of media share that should be array only to move out of the cache. unraidchoupi-diagnostics-20250530-1656.zip

Hi guys, Mover has seem to stopped working. Even when i manually activate it after stopping vms and docker, it wont do anything. I see in the logs only 1 line and that's it. I saw there seemed to be an issue with the plugin, but i did not have it. emhttpd: shcmd (222): /usr/local/sbin/mover start &> /dev/null & Thanks unraidchoupi-diagnostics-20250530-1617.zip

Hello Guys, I haven't touched at my reverse proxy in at least 6 months and i don't think that i have done anything to my server/ network this week. However my setup stopped working : - I can access locally all my containers - If i point my website to my server IP, i reach the swag front page - But if i try adding my subdomain, it ends up in an Error Connection Timed out.( If i try any subdomain that links to nothing, it tells me straight away that it does not exist.) What i tried : - No errors in Swag log, and i deleted the resolver/ proxy.conf to be sure - restarted everthing - tested cloudflare is working So i'm starting to go mad. From above i conclude that cloudflare is working + Local containers are working + Modem/router are redirecting all request to the containers. So why is swag not opening the containers? Starting to go mad here, if you have any ideas. Edit for Solution: After a while searching and trying out stuff. I switched dns only in cloudflare in the Cname (it used to work before, as shown in space invader video) to proxied. It worked instantly.

Any update on the subject, i'm getting the same now

Well, I switched Disk 1. It rebuilded with a few errors (most likely a few seconds of a film were lost). Did a few preclear on the dying disk, and it was really dyning. I'm waiting for a second disk to come in to replace the other failing drive. I'm also waiting for a new controller, Just to be sure. Overall it was a good learning experience. Thanks guys for the help.

I did a parity check (non correcting). It returned with 0 errors (with the two failing drives). I am rebuilding the array with a new drive. And then i'll do some preclear on the old drive to see if it was really failing or it was from something else.

All right, it's settled then, i'll switch both of them. And how can i test the Cable/controller? So that i know if i need to replace them as well?

Ok, I just did it. I got Raw read error rate of 0 on disk 2 and 3, and error rate of 5 on the disk 1. Actually after reading into it, it does not seem to matter much because the worst is at 199. which is far above the trehold. Also the multi zone error rate on disk 1 is also at 1. I was wondering if it could be that only the controller /Cable is bad? Could it provoke all those errors? Should i replace the drives now or wait for the new controller/ cables to arrive?

Yes i think you're right, i got disk1 read errors as well on the parity check

You're right, Thanks for that, i edited the first post

Hello, guys, This week end, i installed a new cache drive. But in the process, it bend the cables and the card from the M.2 controller where 3 of my HDD were. when i started unraid, they did not show up, then after fiddling a bit, they showed up. But it was not stable and one disconnected in the middle of a write operations. One of the drive became disabled (red cross on disk 1). I did a smart short test on the three drives and they seemed fine. So i rebuild the array with the disk 1 in place. It finished this morning, but there was 504 errors. Mainly because of disk 2 and a current pending sector. I did smart extended test on all three drives. Disk 3 came back fine, but there was errors on disk 1 and 2 (errors occured - check smart report). I just launched a parity check (without correction). I ordered a new m.2 controller just in case there are more errors (could mean that the controller was damaged). What do i do for disk 1 and 2? it's only media on it, i would not die if i lose some of it. Are the errors really bad? or if there is no more errors, i should be fine? Right now, the overall server is working fine. Thanks for the help WDC_WD40EFRX-68N32N0_WD-WCC7K6SKLNHN-20210830-1651.txt WDC_WD40EFRX-68N32N0_WD-WCC7K5VY4XY7-20210830-1604.txt WDC_WD40EFRX-68N32N0_WD-WCC7K5VY42E9-20210830-1727.txt unraidchoupi-diagnostics-20210830-1727.zip

Hello Guys, i successfully installed the docker and Git cloned one of my Mobile project. However when i tried to npm install it and expo install it, i got error code EACCS with permission denied to /usr/lib/modules. Does anyone of you actually succeeded on creating an node.Js developing environment? edit 1: I saw the Docker mods, so that's working, i need to open a few more ports for expoto work. But it seems a lot smoother than last time i tried edit 2 : I made Expo.io work, but same as node.js , i need to reinstall it everytime. Is there a dockerMods for Expo.io?