dawhit

I currently using Unraid version 6.11.5

Yes, I have the Shinobi on a VLAN. I followed @SpaceInvaderOne setup. I also have pfsense setup in VM that the VLAN is configured on.

Please check your shinobi.subdomain.conf in your proxy-conf folder. find "set $upstream_app shinobi;" I changed this to "set $upstream_app myipaddress;" that is the address of my shinobi container. When I changed this, my swag reverse proxy started working correctly. Hope this helps.

Not yet, I have been really busy and have not had a chance. Did you get it resolved?

tower-diagnostics-20200405-1548 I tried to upload in one file and it failed. network.cfg share.cfg super.dat ident.cfg domain.cfg flash.cfg go smb-extra.conf docker.cfg disk.cfg docker.txt libvirt.txt syslog.txt Windows 10.txt Ubuntu Server.txt pfsense.txt lsscsi.txt iommu_groups.txt vars.txt ifconfig.txt lsusb.txt folders.txt lsmod.txt top.txt cmdline.txt loads.txt lsof.txt motherboard.txt ethtool.txt plugins.txt df.txt memory.txt btrfs-usage.txt lscpu.txt lspci.txt meminfo.txt ps.txt unraid-6.8.3.txt pfsense.xml

Eth0 errors info is showing 1076 errors under the transmit counters, and 0 errors on the receive counters . Eth0 is running at 100 mbs and not at 1000 mb speeds. I have been doing a lot of reading in the forums and most have said it is the cables or the switch. I have a new switch and have built several cat5e cables, one meter long, type a and b. I have unplugged the cable and inspected the wires in the nic and all is well. I am using a 4 nic Asus server mother board and 1st port is for unraid and the other 3 have been hidden and being used for pfsense vm. All 3 pfsense ports are at gig speeds. attached is sys log syslog.txt Thanks for your help David

Thanks Dan, Yes, I have the DHCP server enabled on the vlan 50 network. I also have 4 cameras working on this vlan. I can access the cameras from the lan interface with ease. Wondering if my nic can cause this problem. It is only running at 100 speed and half duplex. It should be at gig speeds. I'm still trying to resolve this issue. Thanks for your help David

Hi Everyone, I keep getting a cannot resolve host error when I connect Shinobi to the vlan 50 address. fatal: unable to access 'https://gitlab.com/Shinobi-Systems/Shinobi.git/': Could not resolve host: gitlab.com When I connect it to the bridge or proxynet networks it is successful and works. I have built my vlan on pfsense and it is giving dhcp leases and connecting to the internet. I have deleted Shinobi and I have followed Spaceinvaderone's directions, many times over, and get the same results. Many thanks Sir for your awesome videos! Vlans is enabled in eth0 with number 50. Docker is configured with br0.50 and address is 192.168.50.0 with 192.168.50.1 set for the gateway Shinobi pro container is configured 192.168.50.10 using port 8080 Ping from Unraid terminal to 50.1 successful Ping form Unraid terminal to 50.10 fails Ping from Pfsense Lan and cctv interfaces to 50.1 successful clearly the container is not connecting to the 50.0 network, or it is being blocked, I do not know how to proceed from here. Any help resolving this deserves great gratitude. Thank you

Thank you for your help.

I currently trying to run PFSence in a VM. Is it possible to passthrough 2 of the 4 lans of the main motherboard lans? They are all on separate IOMMU groups. Here is my info. IOMMU group 18:[8086:1533] 09:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03) IOMMU group 19:[8086:1533] 0a:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03) IOMMU group 20:[8086:1533] 0b:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03) IOMMU group 21:[8086:1533] 0c:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03) Model: Custom M/B: ASUSTeK COMPUTER INC. - P10S-C Series CPU: Intel® Xeon® CPU E3-1275 v6 @ 3.80GHz HVM: Enabled IOMMU: Enabled Cache: 128 kB, 1024 kB, 8192 kB Memory: 32 GB Single-bit ECC (max. installable capacity 64 GB) Network: bond0: fault-tolerance (active-backup), mtu 1500 eth0: 1000 Mb/s, full duplex, mtu 1500 eth1: 1000 Mb/s, full duplex, mtu 1500 eth2: not connected eth3: not connected Kernel: Linux 4.18.20-unRAID x86_64 Thank you David

Version: 6.6.2 what is the proper way to edit extra domains variable in lets encrypt. I cant seem to make it work correctly.

Correct you are! SanDisk is dead. I will replace the flash drive. Thank you.

Thanks to all whom have worked so hard to perfect Unraid server and make it more user friendly for people like me. I always look for answers to my problems on the forums and found the answer I needed. I followed the directions that Frank1940 provided back in January on this very topic. I used a windows 10 computer, opened cmd prompt as an administrator and ran chckdsk /f and received an reply back of "check disk cannot perform this action because disk is write protected. What would one suggest I try next. Thank you David