Sam.Chapple
-
Posts
16 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Posts posted by Sam.Chapple
-
-
I have recently set unraid backup after using windows server. Well using windows server I was using the qlogic qle3242 dual port is there support for unraid as they support linux redhat.
https://support.hpe.com/hpesc/public/swd/detail?swItemId=MTX_f8164a937a66491ba9291f2692
-
I am building in the fantec 1873 and I need a SAS card that can support all the 6 SAS ports in the fantec 1873. Anyone got any ideas of cards I can use?
-
Sorry to be a pain again. I have just tried to use sg_format for my drives and im getting this error
-
Hi I have just tried to use sg_format for my drives and im getting this error
-
5 hours ago, johnnie.black said:
Some of the disks are formatted with a 520byte sector size, that's not supported, you can usually re-format to 512 with SGutils.
P.S. HBA is in RAID mode, IT would be better.
Thank you so much!!!
-
-
6 hours ago, johnnie.black said:
That's just for boot selection, it doesn't matter for Unraid, all devices should be assignable.
they dont show in unriad or bios its odd
-
On 2/3/2020 at 1:28 AM, Hoopster said:
Likely, because as @johnnie.black noted, that controller does not support being cross-flashed to IT mode. There are several models of LSI controllers mentioned in these forums that do support IT mode. It appears from some searching that it may not support JBOD either. The 926x line has a 2208 chip which, apparently, is RAID only.
Your best bet is to pick up an LSI controller that does support cross flashing to IT mode. Those based on the 2008 or 2308 chips are popular. Someone reported having been able to flash a 2208 controller with 2308 IT firmware, but, that is risky to say the least and I am not sure I would trust that report.
Hi sorry for the spam I got a new card and the drives show on unriad however im getting this message "5 supportable devices of 20 are presented for system boot selection" only 15 drives are showing. As its picking up 20 is there something I need to do to get the last 5 to work or are they dead drives?
-
Do you reccomed any that would work with a dell C2100 and has 2 ports
-
On 1/29/2020 at 8:37 PM, Hoopster said:
05:00.0 RAID bus controller [0104]: Broadcom / LSI MegaRAID SAS 2108 [Liberator] [1000:0079] (rev 05) Subsystem: Broadcom / LSI MegaRAID SAS 9260-8i [1000:9261] Kernel driver in use: megaraid_sas Kernel modules: megaraid_sas@Sam.Chapple Your controller is in RAID mode using the MegaRAID driver. You should try flashing it to IT mode. RAID cards don't work well with unRAID (emphasis on the 'un') and drives attached to them won't show up in unRAID.
Im getting the error to the side when trying to upgrade firmware. "no lsi sas adapters found! limited command set avalible!" "Advanced mode set"
-
12 hours ago, johnnie.black said:
Likely not the same issue, but please post the diagnostics: Tools -> Diagnostics
-
On 1/9/2020 at 4:44 PM, johnnie.black said:
On the main GUI page click on cache and scroll down to "Syslinux Configuration", look for "append" and remove 1000:0054 from the boot command.
Sorry to drop in I am having the same issue.
-
I have recently setup my server however my drives that are seated dont show on the Array Devices however show in the bios.
Server:
Dell PowerEdge C2100
Intel Xeon CPU X5650 x2
98GB Ram
LSI 9260-8i RAID
-
Thank you! seems to work now switched to france and is working all good now!
-
Hi First off for some reason it wouldnt let me post in the plugin support section :/ so posting here.
I am currently having issues setting up the vpn I have watched Spaceinvader Ones tutorial on it and still having issues starting it up.
I am using PIA as the VPN and as per the video i moved the files in the relevent folder for the netherlands cert etc. but just wont load the web UI
Custom Docker Network
in General Support
Posted
Am I doing something wrong? I created a custom docker network using the command "(docker network create 'Network-Name')" is there a new method to this?
Version: 6.11.0-rc4
docker run -d --name='NginxProxyManager' --net='Network-Name' -e TZ="America/Los_Angeles" -e HOST_OS="Unraid" -e HOST_HOSTNAME="Tower" -e HOST_CONTAINERNAME="NginxProxyManager" -e 'USER_ID'='99' -e 'GROUP_ID'='100' -e 'UMASK'='000' -e 'APP_NICENESS'='' -e 'DISABLE_IPV6'='0' -l net.unraid.docker.managed=dockerman -l net.unraid.docker.webui='http://[IP]:[PORT:8181]' -l net.unraid.docker.icon='https://raw.githubusercontent.com/jlesage/docker-templates/master/jlesage/images/nginx-proxy-manager-icon.png' -p '7818:8181/tcp' -p '1880:8080/tcp' -p '18443:4443/tcp' -v '/mnt/user/appdata/NginxProxyManager':'/config':'rw' 'jlesage/nginx-proxy-manager' 819e857e19bdcb7d31a4232ffbba630c8a30de728c3f084533c22cf1a1c67db2 docker: Error response from daemon: network 'Network-Name' not found. The command failed.