Hi,
UnRAID newb here. I finally got my system set up, and finished the pre-clears of my 160gig cache drive, and 2 of my 1TB drives. But the results of my 1TB drives worry me a little - see below:
Disk 1:
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 111 099 006 Pre-fail Always - 30504968
3 Spin_Up_Time 0x0003 096 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 148
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 076 060 030 Pre-fail Always - 45597486
9 Power_On_Hours 0x0032 076 076 000 Old_age Always - 21305
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 148
183 Runtime_Bad_Block 0x0000 001 001 000 Old_age Offline - 511
184 End-to-End_Error 0x0032 001 001 099 Old_age Always FAILING_NOW 1087
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 090 000 Old_age Always - 485338710131
189 High_Fly_Writes 0x003a 096 096 000 Old_age Always - 4
190 Airflow_Temperature_Cel 0x0022 045 043 045 Old_age Always FAILING_NOW 55 (7 102 57 53)
194 Temperature_Celsius 0x0022 055 057 000 Old_age Always - 55 (0 10 0 0)
195 Hardware_ECC_Recovered 0x001a 045 016 000 Old_age Always - 30504968
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 154687542154407
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 3729696396
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1220836389
SMART Error Log Version: 1
ATA Error Count: 771 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 771 occurred at disk power-on lifetime: 19065 hours (794 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 81 87 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 00 00 00 00 a0 00 6d+01:59:03.942 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 6d+01:59:03.934 IDENTIFY DEVICE
00 00 00 00 00 00 00 04 6d+01:59:03.778 NOP [Abort queued commands]
00 00 00 00 00 00 00 ff 6d+01:59:03.467 NOP [Abort queued commands]
a1 00 04 81 87 80 e0 00 6d+01:58:58.669 IDENTIFY PACKET DEVICE
Error 770 occurred at disk power-on lifetime: 19065 hours (794 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 81 87 80 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 00 6d+01:59:03.934 IDENTIFY DEVICE
00 00 00 00 00 00 00 04 6d+01:59:03.778 NOP [Abort queued commands]
00 00 00 00 00 00 00 ff 6d+01:59:03.467 NOP [Abort queued commands]
a1 00 04 81 87 80 e0 00 6d+01:58:58.669 IDENTIFY PACKET DEVICE
ec 00 01 01 a5 5a a0 00 6d+01:58:58.669 IDENTIFY DEVICE
Error 769 occurred at disk power-on lifetime: 19065 hours (794 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 81 87 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 04 81 87 80 e0 00 6d+01:58:58.669 IDENTIFY PACKET DEVICE
ec 00 01 01 a5 5a a0 00 6d+01:58:58.669 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 6d+01:58:52.621 NOP [Abort queued commands]
a1 00 04 81 87 80 e0 00 6d+01:58:02.172 IDENTIFY PACKET DEVICE
ec 00 01 01 a5 5a a0 00 6d+01:58:02.171 IDENTIFY DEVICE
Error 768 occurred at disk power-on lifetime: 19065 hours (794 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 81 87 80 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 01 01 a5 5a a0 00 6d+01:58:58.669 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 6d+01:58:52.621 NOP [Abort queued commands]
a1 00 04 81 87 80 e0 00 6d+01:58:02.172 IDENTIFY PACKET DEVICE
ec 00 01 01 a5 5a a0 00 6d+01:58:02.171 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 6d+01:57:56.137 NOP [Abort queued commands]
Error 767 occurred at disk power-on lifetime: 19065 hours (794 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 71 04 81 87 80 e0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 04 81 87 80 e0 00 6d+01:58:02.172 IDENTIFY PACKET DEVICE
ec 00 01 01 a5 5a a0 00 6d+01:58:02.171 IDENTIFY DEVICE
00 00 00 00 00 00 00 ff 6d+01:57:56.137 NOP [Abort queued commands]
a1 00 00 00 00 00 a0 00 4d+17:12:10.963 IDENTIFY PACKET DEVICE
ec 00 00 00 00 00 a0 00 4d+17:12:10.955 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Disk 2:
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 116 099 006 Pre-fail Always - 114346445
3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 184
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always - 872356
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 495
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 101
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 045 045 045 Old_age Always FAILING_NOW 55 (Lifetime Min/Max 43/55)
194 Temperature_Celsius 0x0022 055 055 000 Old_age Always - 55 (0 10 0 0)
195 Hardware_ECC_Recovered 0x001a 053 034 000 Old_age Always - 114346445
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 4
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 1683627180719
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 956013207
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2434773067
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
It seems both drives complained about heat, so I'll resolve that with better ventilation.
But drive one also reported an end to end error. I'm not sure what this means.
I should add that previously, drive 1 was in another PC with what I believe to be a faulty SATA controller. Could these errors be a left-over from that?
Any comments or advice?
Thanks!
smart_finish_sda.txt
smart_finish_sdb.txt
