June 8, 20242 yr I have moved unRAID to a HP dl380 gen10. The NIC is a HPE Eth 10/25Gb 2p 622FLR-SFP28 CNA This does not seem to have drivers in unRAID. I was previously able to use it on the same server in Proxmox, so I know the NIC is working. How can I add drivers to unraid?
June 8, 20242 yr Author 5d:00.0 Ethernet controller: QLogic Corp. FastLinQ QL41000 Series 10/25/40/50GbE Controller (rev 02) DeviceName: Embedded FlexibleLOM 1 Port 1 Subsystem: Hewlett Packard Enterprise 10/25GbE 2P QL41262HMCU-HP Adapter Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 255 NUMA node: 0 IOMMU group: 3 Region 0: Memory at e8260000 (64-bit, prefetchable) [size=128K] Region 2: Memory at e7800000 (64-bit, prefetchable) [size=8M] Region 4: Memory at e82b0000 (64-bit, prefetchable) [size=64K] Expansion ROM at e6c00000 [virtual] [disabled] [size=512K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/8 Maskable+ 64bit+ Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 25W DevCtl: CorrErr- NonFatalErr+ FatalErr+ UnsupReq- RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 8GT/s, Width x8, ASPM not supported ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 8GT/s, Width x8 TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp+ ExtTPHComp- AtomicOpsCap: 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkCap2: Supported Link Speeds: 2.5-8GT/s, Crosslink- Retimer- 2Retimers- DRS- LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance Preset/De-emphasis: -6dB de-emphasis, 0dB preshoot LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete+ EqualizationPhase1+ EqualizationPhase2+ EqualizationPhase3+ LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [b0] MSI-X: Enable- Count=129 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00001000 Capabilities: [d0] Vital Product Data Product Name: HPE Eth 10/25Gb 2p 622FLR-SFP28 CNA Read-only fields: [PN] Part number: 867332-001 [EC] Engineering changes: A-5739 [MN] Manufacture ID: 1590 [V0] Vendor specific: 15.0W/9.5W PCIeGen3,Arrowhead [V1] Vendor specific: 4.1.4.25 [V2] Vendor specific: 5805 [V3] Vendor specific: 8.35.3.0 [V5] Vendor specific: 0A [V6] Vendor specific: 2.0.19 [V7] Vendor specific: 622FLR-SFP28 [SN] Serial number: MY58050FW3 [V4] Vendor specific: 94F128B5E636 [RV] Reserved: checksum good, 3 byte(s) reserved End Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Capabilities: [148 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [168 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [178 v1] Power Budgeting <?> Capabilities: [188 v1] Alternative Routing-ID Interpretation (ARI) ARICap: MFVC- ACS-, Next Function: 1 ARICtl: MFVC- ACS-, Function Group: 0 Capabilities: [198 v1] Secondary PCI Express LnkCtl3: LnkEquIntrruptEn- PerformEqu- LaneErrStat: 0 Capabilities: [1f8 v1] Transaction Processing Hints Interrupt vector mode supported Device specific mode supported Steering table in MSI-X table Capabilities: [284 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [28c v1] Vendor Specific Information: ID=0002 Rev=3 Len=100 <?> Capabilities: [38c v1] Vendor Specific Information: ID=0001 Rev=1 Len=038 <?> Capabilities: [3c4 v1] Precision Time Measurement PTMCap: Requester:+ Responder:- Root:- PTMClockGranularity: Unimplemented PTMControl: Enabled:- RootSelected:- PTMEffectiveGranularity: Unknown Capabilities: [3d0 v1] Vendor Specific Information: ID=0003 Rev=1 Len=054 <?> Capabilities: [424 v1] Physical Resizable BAR BAR 2: current size: 8MB, supported: 1MB 2MB 4MB 8MB 5d:00.1 Ethernet controller: QLogic Corp. FastLinQ QL41000 Series 10/25/40/50GbE Controller (rev 02) DeviceName: Embedded FlexibleLOM 1 Port 2 Subsystem: Hewlett Packard Enterprise 10/25GbE 2P QL41262HMCU-HP Adapter Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 255 NUMA node: 0 IOMMU group: 3 Region 0: Memory at e8240000 (64-bit, prefetchable) [size=128K] Region 2: Memory at e7000000 (64-bit, prefetchable) [size=8M] Region 4: Memory at e82a0000 (64-bit, prefetchable) [size=64K] Expansion ROM at e6c80000 [virtual] [disabled] [size=512K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/8 Maskable+ 64bit+ Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 25W DevCtl: CorrErr- NonFatalErr+ FatalErr+ UnsupReq- RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 256 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 8GT/s, Width x8, ASPM not supported ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 8GT/s, Width x8 TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp+ ExtTPHComp- AtomicOpsCap: 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- 10BitTagReq- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [b0] MSI-X: Enable- Count=129 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00001000 Capabilities: [d0] Vital Product Data Product Name: HPE Eth 10/25Gb 2p 622FLR-SFP28 CNA Read-only fields: [PN] Part number: 867332-001 [EC] Engineering changes: A-5739 [MN] Manufacture ID: 1590 [V0] Vendor specific: 15.0W/9.5W PCIeGen3,Arrowhead [V1] Vendor specific: 4.1.4.25 [V2] Vendor specific: 5805 [V3] Vendor specific: 8.35.3.0 [V5] Vendor specific: 0A [V6] Vendor specific: 2.0.19 [V7] Vendor specific: 622FLR-SFP28 [SN] Serial number: MY58050FW3 [V4] Vendor specific: 94F128B5E636 [RV] Reserved: checksum good, 3 byte(s) reserved End Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP- SDES+ TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Capabilities: [168 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [178 v1] Power Budgeting <?> Capabilities: [188 v1] Alternative Routing-ID Interpretation (ARI) ARICap: MFVC- ACS-, Next Function: 2 ARICtl: MFVC- ACS-, Function Group: 0 Capabilities: [1f8 v1] Transaction Processing Hints Interrupt vector mode supported Device specific mode supported Steering table in MSI-X table Capabilities: [28c v1] Vendor Specific Information: ID=0002 Rev=3 Len=100 <?> Capabilities: [38c v1] Vendor Specific Information: ID=0001 Rev=1 Len=038 <?> Capabilities: [3d0 v1] Vendor Specific Information: ID=0003 Rev=1 Len=054 <?> Capabilities: [424 v1] Physical Resizable BAR BAR 2: current size: 8MB, supported: 1MB 2MB 4MB 8MB tacgnol-core-diagnostics-20240608-2314.zip
June 8, 20242 yr Author https://support.hpe.com/connect/s/product?language=en_US&kmpmoid=1010203200&tab=driversAndSoftware&driversAndSoftwareFilter=8000113 There are drivers for it here, but unlike RHEL/SUSE or whatever else, no idea how I can add drivers to unraid.
June 8, 20242 yr Community Expert Unraid currently does not include that driver, but I requested it to be added for another user a few weeks ago, hopefully it will be included with 6.13, the first beta should be out very soon.
June 9, 20242 yr Author Thanks..... Does that mean it might come in 6.13 or it likely will? If not, I need to look at virtualising unraid in proxmox I guess.
June 9, 20242 yr Community Expert LT is usually pretty quick at adding extra NIC drivers, so I would say likely.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.