mikedpitt420 Posted September 25, 2016 Share Posted September 25, 2016 Recently I have noticed my server kicking a drive out of the array. After a reboot (or sometimes 2) the array appears fine. I've checked all of my connections and even replaced the SATA cable just to eliminate that. Here is the most recent report on that drive: smartctl 6.2 2013-07-26 r3841 [x86_64-linux-4.1.18-unRAID] (local build) Copyright © 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST3000NC002-1DY166 Serial Number: Z1F372CY LU WWN Device Id: 5 000c50 063a07a96 Firmware Version: CN02 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Sun Sep 25 18:00:32 2016 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 348) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x10bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 073 063 044 Pre-fail Always - 24238264 3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 095 095 020 Old_age Always - 5946 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 065 060 030 Pre-fail Always - 25792556751 9 Power_On_Hours 0x0032 074 074 000 Old_age Always - 22788 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 102 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 099 099 000 Old_age Always - 1 190 Airflow_Temperature_Cel 0x0022 072 057 045 Old_age Always - 28 (Min/Max 22/33) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 25 193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 5946 194 Temperature_Celsius 0x0022 028 043 000 Old_age Always - 28 (0 10 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 199 000 Old_age Always - 21 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Also what I thought may be relevant is the disk log information when I click the actual disk Icon from the "MAIN" tab in the unRAID UI, which is below. This drive isn't what I would consider VERY old, but I'm just wondering if it's the drive, or if perhaps the motherboard SATA connection has an issue. Sep 24 17:51:19 Tower kernel: ata7: SATA max UDMA/133 abar m2048@0xfeb51000 port 0xfeb51200 irq 38 Sep 24 17:51:19 Tower kernel: ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Sep 24 17:51:19 Tower kernel: ata7.00: link online but device misclassified Sep 24 17:51:19 Tower kernel: ata7: link online but 1 devices misclassified, retrying Sep 24 17:51:19 Tower kernel: ata7: reset failed (errno=-11), retrying in 10 secs Sep 24 17:51:19 Tower kernel: ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Sep 24 17:51:19 Tower kernel: ata7.00: link online but device misclassified Sep 24 17:51:19 Tower kernel: ata7: link online but 1 devices misclassified, retrying Sep 24 17:51:19 Tower kernel: ata7: reset failed (errno=-11), retrying in 10 secs Sep 24 17:51:19 Tower kernel: ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Sep 24 17:51:19 Tower kernel: ata7.00: link online but device misclassified Sep 24 17:51:19 Tower kernel: ata7: link online but 1 devices misclassified, retrying Sep 24 17:51:19 Tower kernel: ata7: reset failed (errno=-11), retrying in 35 secs Sep 24 17:51:19 Tower kernel: ata7: limiting SATA link speed to 1.5 Gbps Sep 24 17:51:19 Tower kernel: ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Sep 24 17:51:19 Tower kernel: ata7.00: ATA-8: ST3000NC002-1DY166, Z1F372CY, CN02, max UDMA/133 Sep 24 17:51:19 Tower kernel: ata7.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA Sep 24 17:51:19 Tower kernel: ata7.00: configured for UDMA/133 Sep 24 17:51:19 Tower kernel: sd 5:0:0:0: [sdh] 5860533168 512-byte logical blocks: (3.00 TB/2.73 TiB) Sep 24 17:51:19 Tower kernel: sd 5:0:0:0: [sdh] 4096-byte physical blocks Sep 24 17:51:19 Tower kernel: sd 5:0:0:0: [sdh] Write Protect is off Sep 24 17:51:19 Tower kernel: sd 5:0:0:0: [sdh] Mode Sense: 00 3a 00 00 Sep 24 17:51:19 Tower kernel: sd 5:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Sep 24 17:51:19 Tower kernel: sdh: sdh1 Sep 24 17:51:19 Tower kernel: sd 5:0:0:0: [sdh] Attached SCSI disk Sep 24 17:52:08 Tower emhttp: ST3000NC002-1DY166_Z1F372CY (sdh) 2930266584 Sep 24 17:52:08 Tower kernel: md: import disk6: [8,112] (sdh) ST3000NC002-1DY166_Z1F372CY size: 2930266532 Sep 24 17:52:09 Tower emhttp: shcmd (13): /usr/local/sbin/set_ncq sdh 1 &> /dev/null Sep 24 17:53:21 Tower kernel: ata7.00: exception Emask 0x10 SAct 0x0 SErr 0x400000 action 0x6 frozen Sep 24 17:53:21 Tower kernel: ata7.00: irq_stat 0x48000001, interface fatal error Sep 24 17:53:21 Tower kernel: ata7: SError: { Handshk } Sep 24 17:53:21 Tower kernel: ata7.00: failed command: WRITE DMA EXT Sep 24 17:53:21 Tower kernel: ata7.00: cmd 35/00:00:50:49:ab/00:01:ae:00:00/e0 tag 22 dma 131072 out Sep 24 17:53:21 Tower kernel: ata7.00: status: { DRDY ERR } Sep 24 17:53:21 Tower kernel: ata7.00: error: { ICRC ABRT } Sep 24 17:53:21 Tower kernel: ata7: hard resetting link Sep 24 17:53:21 Tower kernel: ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Sep 24 17:53:21 Tower kernel: ata7.00: configured for UDMA/133 Sep 24 17:53:21 Tower kernel: ata7: EH complete Any help is greatly appreciated, and thank you very much. Quote Link to comment
Frank1940 Posted September 25, 2016 Share Posted September 25, 2016 Why don't you post up a diagnostic file. IT would provide the gurus with a lot more information. Quote Link to comment
mikedpitt420 Posted September 25, 2016 Author Share Posted September 25, 2016 Here is the diagnostic file tower-diagnostics-20160925-1759.zip Quote Link to comment
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.