Jump to content

[Solved] unRAID not finding all drives on SATA card

dwoods99

By dwoods99
in General Support (V5 and Older)

Recommended Posts

dwoods99 Apprentice

dwoods99

Posted
Posted

I have 8-port Sata card which has always been working fine in the RAID-5 setup.

Now I am trying to get the same system working with unRAID 5.0b2

 

Previously bootup with uBuntu would access the sata card first, assigning those 8 first /dev/sd[a-h]

and then the single PATA/IDE drive with the O/S is assigned /dev/sdi, and then the motherboard's

4-port sata would get /dev/sd[j-m] which I did have 12 x 1TB Seagate drives.

 

Now booting up with unRAID seems to be having trouble with the 8-port sata after the 3rd port, and

so the flash key is being assigned to /dev/sdd

 

The only relevant parts in /var/log/syslog after a reboot that I could find was

Jan 10 18:48:21 Tower kernel: DMI 2.4 present.
Jan 10 18:48:21 Tower kernel: last_pfn = 0x7f600 max_arch_pfn = 0x1000000
Jan 10 18:48:21 Tower kernel: MTRR default type: uncachable
Jan 10 18:48:21 Tower kernel: MTRR fixed ranges enabled:
Jan 10 18:48:21 Tower kernel:   00000-9FFFF write-back
Jan 10 18:48:21 Tower kernel:   A0000-E7FFF uncachable
Jan 10 18:48:21 Tower kernel:   E8000-FFFFF write-protect
Jan 10 18:48:21 Tower kernel: MTRR variable ranges enabled:
Jan 10 18:48:21 Tower kernel:   0 base 000000000 mask F80000000 write-back
Jan 10 18:48:21 Tower kernel:   1 base 07F600000 mask FFFE00000 uncachable
Jan 10 18:48:21 Tower kernel:   2 base 07F800000 mask FFF800000 uncachable
Jan 10 18:48:21 Tower kernel:   3 disabled
Jan 10 18:48:21 Tower kernel:   4 disabled
Jan 10 18:48:21 Tower kernel:   5 disabled
Jan 10 18:48:21 Tower kernel:   6 disabled
Jan 10 18:48:21 Tower kernel:   7 disabled
...
Jan 10 18:48:21 Tower kernel: eth0: RTL8168b/8111b at 0xf823e000, 00:1c:c0:bc:1f:8b, XID 98500000 IRQ 27
Jan 10 18:48:21 Tower kernel: sata_mv 0000:04:05.0: version 1.28
Jan 10 18:48:21 Tower kernel: sata_mv 0000:04:05.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
Jan 10 18:48:21 Tower kernel: sata_mv 0000:04:05.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx
Jan 10 18:48:21 Tower kernel: scsi0 : sata_mv
Jan 10 18:48:21 Tower kernel: scsi1 : sata_mv
Jan 10 18:48:21 Tower kernel: scsi2 : sata_mv
Jan 10 18:48:21 Tower kernel: scsi3 : sata_mv
Jan 10 18:48:21 Tower kernel: scsi4 : sata_mv
Jan 10 18:48:21 Tower kernel: scsi5 : sata_mv
Jan 10 18:48:21 Tower kernel: scsi6 : sata_mv
Jan 10 18:48:21 Tower kernel: scsi7 : sata_mv
Jan 10 18:48:21 Tower kernel: ata1: SATA max UDMA/133 mmio m1048576@0xfe800000 port 0xfe822000 irq 20
Jan 10 18:48:21 Tower kernel: ata2: SATA max UDMA/133 mmio m1048576@0xfe800000 port 0xfe824000 irq 20
Jan 10 18:48:21 Tower kernel: ata3: SATA max UDMA/133 mmio m1048576@0xfe800000 port 0xfe826000 irq 20
Jan 10 18:48:21 Tower kernel: ata4: SATA max UDMA/133 mmio m1048576@0xfe800000 port 0xfe828000 irq 20
Jan 10 18:48:21 Tower kernel: ata5: SATA max UDMA/133 mmio m1048576@0xfe800000 port 0xfe832000 irq 20
Jan 10 18:48:21 Tower kernel: ata6: SATA max UDMA/133 mmio m1048576@0xfe800000 port 0xfe834000 irq 20
Jan 10 18:48:21 Tower kernel: ata7: SATA max UDMA/133 mmio m1048576@0xfe800000 port 0xfe836000 irq 20
Jan 10 18:48:21 Tower kernel: ata8: SATA max UDMA/133 mmio m1048576@0xfe800000 port 0xfe838000 irq 20
Jan 10 18:48:21 Tower kernel: usb 1-2: configuration #1 chosen from 1 choice
Jan 10 18:48:21 Tower kernel: scsi8 : SCSI emulation for USB Mass Storage devices
Jan 10 18:48:21 Tower kernel: usb-storage: device found at 2
Jan 10 18:48:21 Tower kernel: usb-storage: waiting for device to settle before scanning
Jan 10 18:48:21 Tower kernel: ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jan 10 18:48:21 Tower kernel: ata1.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Jan 10 18:48:21 Tower kernel: ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Jan 10 18:48:21 Tower kernel: ata1.00: configured for UDMA/133
Jan 10 18:48:21 Tower kernel: scsi 0:0:0:0: Direct-Access     ATA      WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Jan 10 18:48:21 Tower kernel: sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
Jan 10 18:48:21 Tower kernel: sd 0:0:0:0: [sda] Write Protect is off
Jan 10 18:48:21 Tower kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Jan 10 18:48:21 Tower kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or F
UA
Jan 10 18:48:21 Tower kernel:  sda: sda1
Jan 10 18:48:21 Tower kernel: sd 0:0:0:0: [sda] Attached SCSI disk
Jan 10 18:48:21 Tower kernel: ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jan 10 18:48:21 Tower kernel: ata2.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
Jan 10 18:48:21 Tower kernel: ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Jan 10 18:48:21 Tower kernel: ata2.00: configured for UDMA/133
Jan 10 18:48:21 Tower kernel: scsi 1:0:0:0: Direct-Access     ATA      WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
Jan 10 18:48:21 Tower kernel: sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
Jan 10 18:48:21 Tower kernel: sd 1:0:0:0: [sdb] Write Protect is off
Jan 10 18:48:21 Tower kernel: sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
Jan 10 18:48:21 Tower kernel: sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or F
UA
Jan 10 18:48:21 Tower kernel:  sdb: sdb1
Jan 10 18:48:21 Tower kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
Jan 10 18:48:21 Tower kernel: ata3: SATA link down (SStatus 0 SControl 300)
Jan 10 18:48:21 Tower kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jan 10 18:48:21 Tower kernel: ata4.00: ATA-8: ST31000333AS, CC1H, max UDMA/133
Jan 10 18:48:21 Tower kernel: ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Jan 10 18:48:21 Tower kernel: ata4.00: configured for UDMA/133
Jan 10 18:48:21 Tower kernel: scsi 3:0:0:0: Direct-Access     ATA      ST31000333AS     CC1H PQ: 0 ANSI: 5
Jan 10 18:48:21 Tower kernel: sd 3:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
Jan 10 18:48:21 Tower kernel: sd 3:0:0:0: [sdc] Write Protect is off
Jan 10 18:48:21 Tower kernel: sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
Jan 10 18:48:21 Tower kernel: sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or F
UA
Jan 10 18:48:21 Tower kernel:  sdc: sdc1
Jan 10 18:48:21 Tower kernel: sd 3:0:0:0: [sdc] Attached SCSI disk
Jan 10 18:48:21 Tower kernel: ata5: COMRESET failed (errno=-32)
Jan 10 18:48:21 Tower kernel: ata5: reset failed (errno=-32), retrying in 8 secs
Jan 10 18:48:21 Tower kernel: scsi 8:0:0:0: Direct-Access     SanDisk  SanDisk Cruzer   8.02 PQ: 0 ANSI: 0 CCS
Jan 10 18:48:21 Tower kernel: usb-storage: device scan complete
Jan 10 18:48:21 Tower kernel: sd 8:0:0:0: [sdd] 15695871 512-byte logical blocks: (8.03 GB/7.48 GiB)
Jan 10 18:48:21 Tower kernel: sd 8:0:0:0: [sdd] Write Protect is off
Jan 10 18:48:21 Tower kernel: sd 8:0:0:0: [sdd] Mode Sense: 45 00 00 08
Jan 10 18:48:21 Tower kernel: sd 8:0:0:0: [sdd] Assuming drive cache: write through
Jan 10 18:48:21 Tower kernel: sd 8:0:0:0: [sdd] Assuming drive cache: write through
Jan 10 18:48:21 Tower kernel:  sdd: sdd1
Jan 10 18:48:21 Tower kernel: sd 8:0:0:0: [sdd] Assuming drive cache: write through
Jan 10 18:48:21 Tower kernel: sd 8:0:0:0: [sdd] Attached SCSI removable disk
Jan 10 18:48:21 Tower kernel: ata5: limiting SATA link speed to 1.5 Gbps
Jan 10 18:48:21 Tower kernel: ata5: COMRESET failed (errno=-32)
Jan 10 18:48:21 Tower kernel: ata5: reset failed (errno=-32), retrying in 8 secs
Jan 10 18:48:21 Tower kernel: ata5: COMRESET failed (errno=-32)
Jan 10 18:48:21 Tower kernel: ata5: reset failed (errno=-32), retrying in 33 secs
Jan 10 18:48:21 Tower kernel: ata5: COMRESET failed (errno=-32)
Jan 10 18:48:21 Tower kernel: ata5: reset failed, giving up
Jan 10 18:48:21 Tower kernel: ata6: SATA link down (SStatus 0 SControl 300)
Jan 10 18:48:21 Tower kernel: ata7: SATA link down (SStatus 0 SControl 300)
Jan 10 18:48:21 Tower kernel: ata8: SATA link down (SStatus 0 SControl 300)
Jan 10 18:48:21 Tower kernel: piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x01)
Jan 10 18:48:21 Tower kernel: PIIX_IDE 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Jan 10 18:48:21 Tower kernel: piix 0000:00:1f.1: IDE port disabled
Jan 10 18:48:21 Tower kernel: piix 0000:00:1f.1: not 100%% native mode: will probe irqs later
Jan 10 18:48:21 Tower kernel:     ide0: BM-DMA at 0xd0f0-0xd0f7
Jan 10 18:48:21 Tower kernel: Probing IDE interface ide0...
Jan 10 18:48:21 Tower kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Jan 10 18:48:21 Tower kernel: ata_piix 0000:00:1f.2: version 2.13
Jan 10 18:48:21 Tower kernel: ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
Jan 10 18:48:21 Tower kernel: ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
Jan 10 18:48:21 Tower kernel: ata_piix 0000:00:1f.2: setting latency timer to 64
Jan 10 18:48:21 Tower kernel: scsi9 : ata_piix
Jan 10 18:48:21 Tower kernel: scsi10 : ata_piix
Jan 10 18:48:21 Tower kernel: ata9: SATA max UDMA/133 cmd 0xd0e0 ctl 0xd0d0 bmdma 0xd0a0 irq 19
Jan 10 18:48:21 Tower kernel: ata10: SATA max UDMA/133 cmd 0xd0c0 ctl 0xd0b0 bmdma 0xd0a8 irq 19
Jan 10 18:48:21 Tower kernel: i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19

 

I am not sure if "MTRR variable ranges enabled" in the first part is relevant to sata card.

After that I'm wondering about why this is saying 'link down'

Jan 10 18:48:21 Tower kernel: ata3: SATA link down (SStatus 0 SControl 300)

Jan 10 18:48:21 Tower kernel: ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

and ata5 problem

Jan 10 18:48:21 Tower kernel: ata5: COMRESET failed (errno=-32)

Jan 10 18:48:21 Tower kernel: ata5: reset failed (errno=-32), retrying in 8 secs

followed by

Jan 10 18:48:21 Tower kernel: ata6: SATA link down (SStatus 0 SControl 300)

Jan 10 18:48:21 Tower kernel: ata7: SATA link down (SStatus 0 SControl 300)

Jan 10 18:48:21 Tower kernel: ata8: SATA link down (SStatus 0 SControl 300)

 

Any drives plugged into on-board sata are ok, even 2TB WD Green with NTFS content.

 

Any suggestions welcome on what to try next.

 

Link to comment
dwoods99 Apprentice

dwoods99

Posted
  • Author
Posted

Not sure I understand why this was moved to "Other" group since I am asking about Hard drives and my sata controller, but I'll assume it has to do with forum re-structuring.

 

I can't find the controller manual right now, and I can't pull it out of the machine because of a preclear.

 

The sata card was never in a raid mode before, I was using Linux software raid with LVM. All ports worked fine before unRAID.

 

attached is a syslog file after a reboot from original message, I pulled out caddies for slots 4-7

so they are supposed to be down now.  Strange now that 3 is down and 1,2,8 is ok.

syslog.txt

Link to comment
BRiT Mentor

BRiT

Posted
Posted

Not sure I understand why this was moved to "Other" group since I am asking about Hard drives and my sata controller, but I'll assume it has to do with forum re-structuring.

 

It was moved into the appropriate location for unraid 5.0 series (Issues and bugs). If you were trying to use unRAID 4.6 then it would have likely remained in the hard drives and controllers section.

Link to comment

Archived

This topic is now archived and is closed to further replies.

Go to topic listing
×
×
  • Create New...