sfaruque
-
Posts
14 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Store
Gallery
Bug Reports
Documentation
Landing
Posts posted by sfaruque
-
-
On 7/3/2021 at 7:15 PM, SohailS said:
finally figured this one out in case it helps anyone.
the issue I was have was that the disk would not format due to the protection so I needed to disable it. there is a PSID printed on the disk. i used this to reset the disk, by usng the below command where <PSIDNODASHS> is the PSID on the disk and device> is the device
sedutil-cli --PSIDrevertAdminSP <PSIDNODASHS> /dev/<device>
I was then able to run the format command and Type 2 Protection was now removed.
Hopefully this will help someone
Thanks everyone for helping
Hi, I'm in a similar boat where I need to unlock Type 2 protected disk. Could you please let me know how to install the sedutil-cli in Unraid? Thanks
-
No worries. Thanks @itimpi. I've enabled the syslog server and mirrored the logs into the flash drive too. Just a question - is it possible to replace the drive which is 10TB with a 6TB drive (as the drive was only about 45% filled) or rebuild the failed 10TB drive with a couple or more drives that'll total to 10TB?
Thanks.
-
Thanks for your reply @itimpi. Sounds promising. I'll try to get a drive soon. Luckly I did have a diagnostics before I did a reboot. Attached.
Please can you see any issues before I rebooted from the logs?
Appreciate it. Thank you.
-
Hello - I received a 'Device is Disabled, Content Emulated' error with a red cross in one of my data disk (disk2). I've followed some of the threads here and replaced my sata cable with a new one and also changed my sata port to a different one in the motherboard. Despite that change I'm still getting the same error. I'm attaching the latest diagnostics.
Please help. Thank you.
-
8 hours ago, Squid said:
My opinion:
You purchased ECC memory and are using it so that if/when one starts going bad you can replace it. Sure the errors are currently being corrected, but that is simply the stick telling you "replace me". If you have ECC memory and chose to not replace the memory when errors begin to happen then I'd question why you even bought ECC memory and a compatible CPU / motherboard in the first place.
Very valid point. Noted. Thanks.
-
Looks like it was bad DRAM sticks. I've removed them and errors have disappeared. Thanks for your help.
-
4 hours ago, Squid said:
Aug 13 06:05:24 Dhaka kernel: [Hardware Error]: Unified Memory Controller Ext. Error Code: 0, DRAM ECC error. Aug 13 06:05:24 Dhaka kernel: EDAC MC0: 1 CE on mc#0csrow#3channel#0 (csrow:3 channel:0 page:0x5b7962 offset:0x880 grain:64 syndrome:0x1000)
Looks like a bad stick
I'll remove the new sticks and see. Could there be any long term consequences if I leave them there do you think? As the server appears to be running fine.
-
4 hours ago, jonp said:
Are there any symptoms you are noticing or just errors in logs?
I haven't noticed any symptoms - just errors in the logs.
-
Good evening
I've been getting these errors below after upgrading from 6.8.3 to 6.9.2 recently. The server appears to be running fine but I'm worried as these errors were not noticed before the upgrade.
I have a AMD Radeon R7 passed through to a Windows 10 VM. I recently added more ECC Kingston RAM (Total 16GBx4).
MB: Asrock X570 Steel Legend
CPU: AMD Ryzen 7 3700X
Recent diagnostics attached. Any help is much appreciated.
Thanks
-
I think the attached diagnostic was from the day I upgraded to 6.9.1. To troubleshoot the issue - when trying to run nginx from the command prompt I get 'Cannot bind address' and 'address already in use'. Chould this be an issue with the updated Linux kernal that is not compatible with my network card? I have a quad port Intel NIC that I thought should be fine.
-
Thanks for looking into this @Squid. I've been trying to solve this myself and the issue seems to be intermittent. The symptoms described happenes mostly when I reboot the server (I shut it down at night using the S3 Sleep plugin). If I hard reset I seem to access the webGui. I'm attaching couple more syslog for reference from few days ago. (The one that is syslog-20210319-073016.txt was generated when the server started from shutdown overnight).
Sorry about the confusion. Thanks for looking into this.
-
Hello - I upgraded to 6.9 then 6.9.1 from 6.8.3 recently and since then issues with my unraid server.
I connected my box with a monitor and the server boots in the login prompt. However, accessing the server from LAN is not working. I can't SSH into the server from other computers. The Windows Network doesn't show the unraid server. All the SMB shares are not accessible. The only thing I can see on the monitor connected directly to unraid is the login prompt. I can login from the prompt too.
What could be the issue here? I have had more than a year without any issues with 6.8.x. Is there any new settings in the latest release that could be causing the issue?
Mostly I run pfSense VM, Plex, nextCloud etc.
CPU: Ryzen 3600
MB: ASrock X57032GB Kingston ECC Memory
AMD Radeon R7
Latest diagnostics attached for you reference.
Thanks
-
I have similar issue. Unfortunately I can't get into the WebGUI or SSH. The server is basically appears to be DEAD.
I couldn't even get any diagnostics. Is there any way of getting the diagnostics if I don't have access to WebGUI or SSH?
My video card is stubbed with 'System Tools' so Unraid with GUI access from boot doesn't even show anything on the monitor when plugged in directly onto Unraid. What a mess!
Unraid version 6.9.1
ASRock X570 / Ryzen 3600 / 32GB ECC RAM
[SOLVED] Help with a SAS Drive
in General Support
Posted
Thank you @jmztaylor. I've install it and run the command --scan. It says 'The Kernel flag libata.allow_tpm is not set correctly'. Any idea how this is done? I'm looking for the readme but nothing like that downloaded with the sedutil-cli wget.