MacRaid

I didn't, apparently it's an update issue since I heard other guys using it with older UnRaid version. I'm moving countries so unable to try again. Good luck and I'll update if I manage in the future.

Thank you guys for your reply, I was actually performing a Smart Extended Self-test which took a good 8-9hrs and no errors. So I'll let it be with the Smart test (unless I get more recommendations to run a preclear). Thanks again guys and stay safe...

Hey guys, so short story... One of my HDD fail, finally I got a replacement which I formated, mounted (forgot to pre-clear) and then started my UnRaid and now is rebuilding my UnRaid. Question is: 1. Should I let it be or somehow try to unmount and pre-clear? 2. Is it worth it? 3. What are the cons/pros on doing that? P.d. all other drives were precleared. Thanks in advance.

Thanks for confirming that...

Thanks Johnnie, I'll try and do that, at the moment I"m trying to save some family stuff from that disk (which apparently still accesible or maybe I'm just pulling the data from emulated). So I'm putting that data on another disk (inside the unraid) and another external drive then I'll try swapping cables. I'll update as soon as posible.

Hey guys, hope you all are doing well and safe. So yesterday after installing some extra fans on my UnRaid and NO previous failures/warning, all of a sudden about 20min after starting up I had a message that 33 errors were found on my Disk2, later on I got the "Device is disabled..." message. The disk is a WD Red less than 1 year old and as I said no issues before so I suspect I moved a cable while installing the fans, so I open up again a recheck all cables then after re-start the drive shows "not installed". This is the first time sending a log from my UnRaid so let me know if the one below is the one I'm supposed to send. Any help will be appreciated... generationx-diagnostics-20200626-1523.zip

Thanks I just post it in the proper forum. Appreciate it anyhow.

No one around with this Issue and/or solution?

Hey guys, I'm finishing setting up my deluge/sonarr/plex etc environment, I have my deluge working fine with files moving from incomplete to complete to each assigned folder. but the original file in folder "complete" stays there, so I'm trying to install AutoRemovePlus plugin from GUI and manually without success, it just won't appear inside the plugin options even after closing and opening deluge. Can you share some light to solve this issue and/or another plugin or solution? Thanks in advance... UnRaid 6.8.3 Deluge 2.0.4

Thanks Tim, 1. I'm not sure how it can't be accessible from the internet when it uses internet to work plus my download gets register outside my network. I don't know how port forwarding works and/or if it's active nor I know if I need it or not. How "high port" should it be set on deluge and where? 2. How do I get a valid certificate? My private IP is the one I use to access my router, right? 3. Private places need invite and I read they have different rules which I don't yet understand, can I set NordVpn on Unraid and this dockers? I know I'm asking you to level down with me but is much appreciated.

Hi, did you manage to setup nordvpn on your unraid? thread seems to be forgotten...

Thanks for your response Squid, I am accessing from home and atm not interested to have remote access. 3 things I'm concern, 1. So many blogs saying to protect (or not leave it "open) your deluge, sonarr, jackett etc. 2. The URL saying "not secure" and 3. Being able to see anything downloaded with the iknowwhatyoudownload site. I'm not that advance to be sure but I don't think there's anything sniffing around.

Hey guys... So, slowly but surely I'm progressing with my UnRaid and extras. Now I need your help again. I have set up a combination of Jackett, Sonarr, Deluge and Plex. I manage to "secure" my UnRaid with the encryption certificate in Settings/Management Access (so now is https) there are a lot of thing I don't fully understand how they work but still learning. Now with the other mention dockers the URL still shows "Not Secure"on Chrome, I have read a LOT of treads and saw a lot of videos but I wish to hear from you guys the experts in one spot. I wish to protect my UnRaid, my IP, network usage (uploads and downloads history), make it private but funcional... etc. I've read about installing SSL certificates, setting up private ports, using VPN's or alike OpenVpn (too expensive for me), DuckDNS, Private Internet Access (good price), Privoxy (I think is free) etc... I have a NordVpn subscription for another 2 years but can't find anything to set it up for dockers. The question is which configuration or combination would you recommend to accomplish this if possible with no or minimum extra subscriptions required (I know i'm asking a lot) also taking in account my knowledge on the subject is much much less than standard. Thank you in advance and be safe...

Sorry for the late update. So I manage all changes and after reboot it assign the same IP as expected. My Router was tricky since it only had "Reserve IP address" option, but I guess the function is the same. A big thank you to all for your help and patience. Be safe...