whitewraith

Ok so how do i disable bonding? Is it as simple as changing this to no?

so right now it is using the new NIC as eth0 correct and eth1 is disabled. So disabling bonding would be fine. OR if I leave it on and eth0 fails will it roll over to eth1 if i have it connect to my routher?

Will it hurt to leave it enabled? Is it needed for tailscale at all?

Ok so i have gone into the GUI and changed the MAC addresses. Then i rebooted the system and it now states this. I have attached the latest diag file as well. Is this what I want to see? mediahog-diagnostics-20260722-0926.zip

I only used the gui. I did not make any changes to the config file. What is the correct process for adding a new NIC? I understood it to be install chance MAC addresses in gui then reboot and plug Ethernet cable into new nic.

I am not sure I follow you. I went to settings>network settings>interface rules and switched the Mac addresses when i installed the second NIC before i rebooted and moved the ethernet cable to the new NIC. Was that not correct?

mediahog-diagnostics-20260721-0826.zip Sorry here are the diagnostics.

Hello All, I added a new nic card so now I have two one on the MB and on in a pcie slot. How can i tell if they are set up correctly? After I added the card I went to settings network interface rules and switched the MAC addresses so that the new nic should be eth0 and the old one eth1. When i rebooted the server it looks like I am at 2.5Gb speed but it looks like it bonded the two NICs. Is this the way it should be run? It also looks like eth0 is down? But shouldn't it be the other way around?

Could you add tailscale support to the palworld container?

Palworld will not auto update when i restart the docker container.

I hope I can get some help. I installed the palworld docker. I have it set to bridge and can connect once but then I cannot reconnect until I restart the docker. If I set it to br0 and set a static IP it will not connect at all. How can I set it so that I can log out of the game and back in without restarting the docker?

Hello everyone, I get his message in the deluge logs "[info] No torrents with state 'Error' found." This is new to me and I haven't changed any settings but it is not seeding anything. It will let me download. I am not sure what this means or how to fix it?

Hello everyone, I ran preclear on some new drives I am going to add to array. Preclear completed without issue on new drives. I then stopped the array and turned off the server so that I could do some physical cleaning of my jbod and the server. When I turned on the array and server it seemed that the preclear status on the drives is no longer there. Do I have to preclear again? or is it still safe to add to the array?

Here are the diagnostics, please take a look and let me know if you find out what is happening. I am really confused. I am expecting the download share on the cache drive to move to to download share on the array. mediahog-diagnostics-20240405-1034.zip

I am on version 6.12.8 so almost the latest version. when i invoke the mover manual the screen refreshes and mover is working but I have no indication that it is running. It seems to move the files from the cache to the array but it copies the files as after the mover is done they are still on my cache drive. Is there a setting i am missing in this new version? Why is it copying files and not moving them properly?

Yeah I checked and there is tons of room. it seems like mover is broken or something.

Hey everyone, I noticed that files are copied to the array but then I still have them on the cache drive. I download to the array then I have mover set to move them at 3AM to the array. I am noticing that all the files get moved but some still remain on the cache drive. I am not seeing any settings that have changed and I have had it setup this way for years. Any ideas why this might be acting this way now?

I can see my server in file explorer but when i click on it I get prompted for password but it doesn't accept it. This seems to have started since windows 11. I am on UNRaid version 6.12.4 mediahog-diagnostics-20231121-0830.zip

I noticed this for the first time today. What do I do to fix it? It was at the bottom under all my docker containers on the docker tab. Warning: file_put_contents(): Only -1 of 108 bytes written, possibly out of free disk space in /usr/local/emhttp/plugins/dynamix/include/DefaultPageLayout.php on line 714

i wouldnt mind doing that, how do i set that up?

Hey all I do not have a monitor connected to unraid because I usually remote in to the web interface. However I live in Ca and we have rolling brown outs this time of year, is there a way to use an AOC usb monitor with unraid? I would like to be able to plug it in while my server is on my battery back up and shut it down properly before it loses power totally.

Thanks

Maybe a dumb question, but how can i be sure that delugevpn is using the vpn. If it is enabled in the container and then I can open the webui, does that mean it is using the vpn and all is well? Or is it if I can download something with vpn enabled in the container?

I meant the advanced slider in the upper right corner.