meat

They still show in the array for now but the rebuild really isn't doing anything even though says its running. I'll likely have to reboot since I don't know if I can get the rebuild to stop. I acknowledged the error on 3, didn't know you could actually do that.. and I will add 1 and 200 to all drives. I do have several drives and plan to consolidate them eventually. I have a 24 drive disk shelf (3.5") and 16 drives spaces on the new server (2.5") + 2 NVME. The old server only had 8 drive spaces (2.5") Is the HPE Smart Array P816i-a SR Gen10 controller supported? The old server was a Dell and it worked fine.

Disk 5 is only one with a SMART error on the dashboard. Rebuild ran most of the night and hung up at 5 AM when both Disk 3 (ST2000LM015-2E8174_ZDZBD5RC - 2 TB (sdd)) and Disk 9 (ST2000LM015-2E8174_ZDZB5F6A - 2 TB (sdb)) started getting read errors at the same time. Over 60,000,000 read errors each.. Not sure what the issue is, if it is a backplane controller or some other hardware related.. I doubt it's the drives. I'll attach the diagnostic from this morning. If I need to I can more all drives back to my old server and see if it builds on there. If everything works I could then move all data to the disks housed in my disk shelf since the only issues I've had are on the drives directly attached to the new server. I'll wait to do anything until I get feedback from here though. thanks unraid-diagnostics-20240131-0805.zip

Ok, I went ahead and started the new config using the original drives in 3 and 8. I'll let this run overnight and see how it goes. At first glance it looked like data was in both drives and that this should work. I'll report back after the parity rebuilds, thanks for your help.

New Config won't delete any data on the array, correct? Just rebuild the parity? And what about the "Preserve current assignments" I've never had to do this and don't want to F it up.

I will have to read up more on the "New Config" option. I thought that might be an options but after reading the warnings on it I'm a bit unsure how to do it without losing all data on all disks.. As for losing anything written to the emulated disks, it should be extremely minimal and unimportant, I had all dockers and VMs off for nearly the entire time, there may have been a bit of data written to the shares from my NVR but that's no big deal. A second option I considered but not sure if it would work would be to remove the drives and shrink the array, then mount the 2 drives and copy data over to the array, but sounds like the "new config" option would be smoother... if it worked. unraid-diagnostics-20240130-1734.zip

After upgrading to a new machine and moving drives over I had 1 drive fail, followed by another within a few hours. I put in 2 new drives and began the rebuild process and in the middle of that, a 3rd drive failed. At this point I figured it was an issue with drives not fully seated, I had to stop the rebuild since it hung up once the 3rd drive failed. I shut the machine down and pushed all drives in tight to make sure they were fully seated. I also put the original 2 back in as well. When I boot back up the 2 new disks that were being rebuilt said emulated, but when I tried to browse the emulated disk, all data was gone, I'm guessing the parity is shot at this point. I was able to browse the 3rd failed disk that caused the rebuild failure and it is fine, I also mounted the original 2 failed disks and they still have all the data. The good news is, all data is in tact in the respective drives, I just don't know where to go from here. Is it possible to add the original 2 drives back without having them try to rebuild, and then simply rebuild parity? Or what steps should I take?

It's in "File Transfer" mode.

I am trying to connect my old cell phone to my server so I can easily copy off all my data. How can I mount the phone? It isn't showing up in unassigned devices. Do I need to manually mount the device? It is showing up under System Devices: USB Devices: Bus 001 Device 005 Port 1-3.2ID 04e8:6860 Samsung Electronics Co., Ltd Galaxy A5 (MTP)

I had the same problem after upgrading to 6.10.2 Some of the dockers wouldn't start, some would start but I couldn't update or edit, and if I tried to uninstall / reinstall it would fail. I downgraded back to 6.9.2 and so far everything seems to be working fine.

I am using the hassio_supervisor docker container which in turn installs several other containers in Docker including the homeassistant container. I am also running the SWAG container which uses nginx for it's reverse proxy. The problem I'm having is nginx requires a custom bridge network for it to route traffic to the proper container, in this case, the homeassistant container. While I can set the network by editing the hassio_supervisor container, I am unable to edit the homeassistant container and it's using the host network. Does anyone know of any workarounds for this? I'm farily new to unRAID so I'm not sure if it's possible to edit containers from the terminal or if there are other ways to configure nginx files to map to containers on the host network. Any help would be greatly appreciated. I did come across this but I haven't given it a try yet: