Coco

Members
  • Posts

    20
  • Joined

  • Last visited

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Coco's Achievements

Newbie

Newbie (1/14)

1

Reputation

  1. Hi, Just upgraded my hardware on my server, and I get some error that I don't understand. While I am waiting for my 5950x I had to use a 5600g, don't know if the fact that it is an APU could have something to do with it ? motherboard is ASUS x570 gaming e and ram is 4x 8 Gb XPG ddr4 gammix d10. error I get is kernel: pci 0000:09:00.0: BAR 9: failed to assign [mem size 0x00400000 64bit] on different BAR number and also mcelog: ERROR: AMD Processor family 25: mcelog does not support this processor. Please use the edac_mce_amd module I just can't figure out what those errors mean. also since hardware upgrade some of my dockers have been acting weird. wondering if, when I get my new cpu I should just try a fresh unraid install, see if it help. thank you for your time and help. diag file attached. jarvis-diagnostics-20211228-2143.zip
  2. just wanted to show, my acheivement ..... lol thanks again
  3. LSI Corporation SAS2 Flash Utility Version 20.00.00.00 (2014.09.18) Copyright (c) 2008-2014 LSI Corporation. All rights reserved Adapter Selected is a LSI SAS: SAS2008(B2) Controller Number : 0 Controller : SAS2008(B2) PCI Address : 00:04:00:00 SAS Address : 500605b-0-02c8-ccf4 NVDATA Version (Default) : 14.01.00.08 NVDATA Version (Persistent) : 14.01.00.08 Firmware Product ID : 0x2213 (IT) Firmware Version : 20.00.07.00 NVDATA Vendor : LSI NVDATA Product ID : SAS9211-8i BIOS Version : 07.39.02.00 UEFI BSD Version : N/A FCODE Version : N/A Board Name : SAS9211-8i Board Assembly : N/A Board Tracer Number : N/A Finished Processing Commands Successfully. Exiting SAS2Flash.
  4. Good day, finally was able to flash to IT mod, turns out I was forgetting to put a ':' at the end of the line to access the thumb drive in EFI ..... doh!!!! anyway, it is now flsh to firmware 20.00.07 in IT mode. everything seems to be working fine for now, i'll repost if I get another error. just the rebuild process is going way faster since flash, don't know if it is related but went from 75MB/sec to 130 MB/sec ... thanks all for your help.
  5. for now till I figure it out I updated to IR 07, I'll see if it works while I try to figure out how to cross flash it to IT mode
  6. yep that's what I figured. read the thread, I do not understand at all how to this. i'll keep reading and try to figure it out lol thanks for all the help
  7. ok thanks ill give it a go. which one is the better option you think ?
  8. ok, i have tried to flash it but here is the error i get: LSI Corporation SAS2 Flash Utility Version 20.00.00.00 (2014.09.18) Copyright (c) 2008-2014 LSI Corporation. All rights reserved Advanced Mode Set Adapter Selected is a LSI SAS: SAS2008(B2) Executing Operation: Flash Firmware Image Firmware Image has a Valid Checksum. Firmware Version 20.00.07.00 Firmware Image compatible with Controller. Valid NVDATA Image found. NVDATA Version 14.01.00.00 Checking for a compatible NVData image... NVDATA Device ID and Chip Revision match verified. NVDATA Versions Compatible. Valid Initialization Image verified. Valid BootLoader Image verified. ERROR: Cannot Flash IT Firmware over IR Firmware! Firmware Image Validation Failed! Due to error remaining commands will not be executed. Unable to Process Commands. Exiting SAS2Flash. any idea ? also here is the list all result LSI Corporation SAS2 Flash Utility Version 20.00.00.00 (2014.09.18) Copyright (c) 2008-2014 LSI Corporation. All rights reserved Adapter Selected is a LSI SAS: SAS2008(B2) Num Ctlr FW Ver NVDATA x86-BIOS PCI Addr ---------------------------------------------------------------------------- 0 SAS2008(B2) 20.00.06.00 14.01.00.09 07.39.02.00 00:04:00:00 Finished Processing Commands Successfully. Exiting SAS2Flash. thanks
  9. thanx, I'll give it à go later today, I'll let you know. appreciate the help
  10. understood, I'll give the HBA firmware update and post the result, thanx
  11. thanks I'll give this a try. newbie questions here, how foI know which firmware to use? how do I put the firmware on the flash drive, do I need to power down the server and put it on from à pc ? any chance this is going to brick my HBA ? just a little nervous about this has I never played around with this staff. thank you
  12. hi all, I have 2 disks in my array that failed and went to emulated mode in the last 4 days, both disks are not even a year old yet. First one is a 4 tb wd red plus, hosting all my TV shows, went down, rebuild the array, all good. Second one, 2 days later, is another wd red plus, 4tb, went down, rebuild it, all good for not even a day and went down again. I know both disk are good as I tested them et the result showed no errors. Any idea what's going on? could it be because they're to full, almost at capacity now? or because I am currently re-transcoding all my libraries? too much read and writed back to back ? I am restoring the one that failed twice now. any help would be appreciated as it is getting annoying to restore, taking a lot of time and it is close to impossible to use plex while doing it. Movies keep buffering...... thanx jarvis-diagnostics-20211123-0725.zip
  13. Newbie question here, if I install a pihole docker running rsync and keepalived will the config stick after Container update or will have to redo everything again? other question, for now I have 2 adguard home setup with adguardhome-sync. is there a way to set them as fail over ? using keepalibed docker or something? if so anybody know how? hole point if to have the 2 ad blocker not run at the same time but have one take over just if primary goes down. thanks
  14. good day, yes that was it, I had an unuse pool, once I deleted it everything came back to normal. thank all for the help.
  15. Newb question probably, but what empty pool ? brand new to this. thanx