[[6.10.0-rc1/6.10.0-rc2d] USB Passthrough to VM not working correctly [Manual XML solution available]]

1 hour ago, aguilaair said:

 

Make sure it is not ticked in the UI editor:

 

Click save, then paste the new piece again directly through the XML editor.

 Removed  from UI editor and pasted  into xml as suggested rebooted and still not picking up Conbee.  I think i will  remove VM and start again and insert in xml file before I start VM tomorrow?

[[6.10.0-rc1/6.10.0-rc2d] USB Passthrough to VM not working correctly [Manual XML solution available]]

 i have been able to insert the  xml  for the serial port , however it is still not working still receive message in logs  below.

 

 I am looking for help  or do in need to revert back to  6 9.2 . reason  for going to  6.10 rc2  so that i could install window 11 which is working  fine .

 

Any advice for this newbie

[[6.10.0-rc1/6.10.0-rc2d] USB Passthrough to VM not working correctly [Manual XML solution available]]

Amended as  mentioned now i have a similar error on line 46 checked this is seems fine  inserted /  but text turned red. I didn't touch anything in this area ?

 

 Sorry ,so frustrating 

[[6.10.0-rc1/6.10.0-rc2d] USB Passthrough to VM not working correctly [Manual XML solution available]]

 Hi  I have  managed to input the xml code  I have this error , As i said i am new to linux and xml i obviously have it formatted incorrectly , tried several solution but still get the creator error as below.

 

 Any advise would be appreciated.

[[6.10.0-rc1/6.10.0-rc2d] USB Passthrough to VM not working correctly [Manual XML solution available]]

15 minutes ago, NickI said:

 

Yes, you can add it at line 137, it will work just fine

sorry  do i add </memballon> and then <serial type='dev'> <source path='/dev/serial/by-id/
usb-dresden_elektronik_ingenieurtechnik_GmbH_ConBee_II_DE2415359-if00/> <target type='usb-serial' port='1'> <model name='usb-serial'/> </target> <alias name='serial1'/> <address type='usb' bus='0' port='4'/> </serial>

 

like so ?  and change the port from 4 to 1 as this is the port that the conbee ll is on at the moment. ?

[[6.10.0-rc1/6.10.0-rc2d] USB Passthrough to VM not working correctly [Manual XML solution available]]

7 minutes ago, aguilaair said:

 

 

Hey, simply add under </memballoon>

 

 

You can find the ID by going to the terminal and typing in

ls /dev/serial/by-id/

you'll see the Conbee there, simply copy that sting and paste it into the XML. Let me know if i have not explained myself well enough

Sorry where do i add <memballon>  at the end of the xml say line 137?  Do i paste or type the above section into xml ? and do I replace  source path with the  contents  attached.

 

 Apologise for these what may seem simple question.

[[6.10.0-rc1/6.10.0-rc2d] USB Passthrough to VM not working correctly [Manual XML solution available]]

 Hi all , I am new to unraid I too am struggling to load Conbee11 in  6.10.rc2 works fine in 6.9.2

 

  this is the first time i have tried to to change the xml file and i struggling because the text colours are not matching some time i get  green but the next set are always red.

 I noticed in the xml file that the  Conbee is showing in sources  in the entry 126-131. as per attached.

Any advice on how to complete this task would be appreciated