beikesea

Members
  • Posts

    3
  • Joined

  • Last visited

Everything posted by beikesea

  1. Yes, the Unraid is installed on my Dell T7820 Workstation.
  2. Hi, I found the my 10G network card cannot negotiate to 5G link mode after system boot. However, the link speed could recover to 5000bastT/Full after executing command "ethtool -s eth0 autoneg on". My network card is "Intel Corporation Ethernet 10G 2P X550-t Adapter". The switch is NETGEAR MS510TXPP. Here is the process to reproduce the problem: ethtool -i eth0 driver: ixgbe version: 5.15.40-Unraid firmware-version: 0x80000f32, 19.5.12 expansion-rom-version: bus-info: 0000:04:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes supports-priv-flags: yes ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full 2500baseT/Full 5000baseT/Full Supported pause frame use: Symmetric Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: on Port: Twisted Pair PHYAD: 0 Transceiver: internal MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ethtool -s eth0 autoneg on ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full 2500baseT/Full 5000baseT/Full Supported pause frame use: Symmetric Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full 2500baseT/Full 5000baseT/Full Advertised pause frame use: Symmetric Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: 5000Mb/s Duplex: Full Auto-negotiation: on Port: Twisted Pair PHYAD: 0 Transceiver: internal MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes dmesg | grep -i ixgbe [ 39.766547] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver [ 39.766645] ixgbe: Copyright (c) 1999-2016 Intel Corporation. [ 40.601995] ixgbe 0000:04:00.0: Multiqueue Enabled: Rx Queue count = 36, Tx Queue count = 36 XDP Queue count = 0 [ 40.700054] ixgbe 0000:04:00.0: 31.504 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x4 link) [ 40.812033] ixgbe 0000:04:00.0: MAC: 4, PHY: 0, PBA No: J69754-003 [ 40.812149] ixgbe 0000:04:00.0: b4:96:**:**:**:** [ 40.971001] ixgbe 0000:04:00.0: Intel(R) 10 Gigabit Network Connection [ 41.651898] ixgbe 0000:04:00.1: Multiqueue Enabled: Rx Queue count = 36, Tx Queue count = 36 XDP Queue count = 0 [ 41.752195] ixgbe 0000:04:00.1: 31.504 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x4 link) [ 41.866258] ixgbe 0000:04:00.1: MAC: 4, PHY: 0, PBA No: J69754-003 [ 41.866375] ixgbe 0000:04:00.1: b4:96:**:**:**:** [ 42.029314] ixgbe 0000:04:00.1: Intel(R) 10 Gigabit Network Connection [ 43.646539] ixgbe 0000:04:00.1: complete [ 43.661631] ixgbe 0000:04:00.0: complete [ 43.976969] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver [ 43.976972] ixgbe: Copyright (c) 1999-2016 Intel Corporation. [ 44.669028] ixgbe 0000:04:00.0: Multiqueue Enabled: Rx Queue count = 36, Tx Queue count = 36 XDP Queue count = 0 [ 44.769080] ixgbe 0000:04:00.0: 31.504 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x4 link) [ 44.883503] ixgbe 0000:04:00.0: MAC: 4, PHY: 0, PBA No: J69754-003 [ 44.883512] ixgbe 0000:04:00.0: b4:96:**:**:**:** [ 45.048905] ixgbe 0000:04:00.0: Intel(R) 10 Gigabit Network Connection [ 45.740533] ixgbe 0000:04:00.1: Multiqueue Enabled: Rx Queue count = 36, Tx Queue count = 36 XDP Queue count = 0 [ 45.840620] ixgbe 0000:04:00.1: 31.504 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x4 link) [ 45.954050] ixgbe 0000:04:00.1: MAC: 4, PHY: 0, PBA No: J69754-003 [ 45.954059] ixgbe 0000:04:00.1: b4:96:**:**:**:** [ 46.119016] ixgbe 0000:04:00.1: Intel(R) 10 Gigabit Network Connection [ 46.563594] ixgbe 0000:04:00.0: registered PHC device on eth0 [ 46.880177] ixgbe 0000:04:00.1: registered PHC device on eth1 [ 51.336232] ixgbe 0000:04:00.0 eth0: NIC Link is Up 1 Gbps, Flow Control: None [ 323.198656] ixgbe 0000:04:00.0 eth0: NIC Link is Down [ 327.927630] ixgbe 0000:04:00.0 eth0: NIC Link is Up 5 Gbps, Flow Control: None [ 329.425081] ixgbe 0000:04:00.0 eth0: NIC Link is Down [ 329.553606] ixgbe 0000:04:00.0 eth0: NIC Link is Up 5 Gbps, Flow Control: None [ 329.633081] ixgbe 0000:04:00.0 eth0: NIC Link is Down [ 330.177570] ixgbe 0000:04:00.0 eth0: NIC Link is Up 5 Gbps, Flow Control: None [ 330.257093] ixgbe 0000:04:00.0 eth0: NIC Link is Down [ 330.801629] ixgbe 0000:04:00.0 eth0: NIC Link is Up 5 Gbps, Flow Control: None [ 330.881077] ixgbe 0000:04:00.0 eth0: NIC Link is Down [ 331.945575] ixgbe 0000:04:00.0 eth0: NIC Link is Up 5 Gbps, Flow Control: None Thanks! Best regards, Beikesea
  3. Hi, the power shows N/A after upgrading from 6.9.2 to 6.10.0-rc7. Could this be fixed? My card is AMD W5700. The version of Radeon TOP is 2021.11.24. Thanks!