Sargent_-_Merkie

Hi all So I have just started using the array again with a few Samsung 3.84tb SAS ssds and noticed none of them are spinning down seen this plugin on community apps but it still doesn't seem to be spinning them down happy to provide any further information if needed. Drives are MZILT3T8HBLS_007 Iv also got a load of NVME disks U.2 Micron_7300_MTFDHBE7T6TDF these don't look to be spinning down either any suggestions would me much appreciated!

Okay so this is my docker pool that i run all my containers from and any other system bits, i only rebooted as Plex had hung been having an issue with it for a little while now . It basically crashes but states it is running then i try and reboot the container but get a system error pop up. I have tried deleting the container and recreating it but this dosnt seem to resolve it mainly happens after it has been updated. I also haven't upgraded the docker pool since moving to version 7.0.

diagnostics attached from that shutdown. I found a post about SAS disks being unable to spin the disks down, I do have SAS SSDs installed but not sure if this is still relevant or not. gilo2.0-diagnostics-20250127-0753.zip

So finally had to do a reboot as plex stopped working...... I had no consoles open and I got the below during shut down.

humm i didn't think about that! on my next scheduled reboot ill check iv closed them all.

Upgraded from 6.13.0 to 7.0 I migrated away from the array to a full blow ZFS pool listed below which im still copying 77TB of data over from my backup btrfs pool but when i go to shut down or reboot the system it keeps getting stuck on unmounting shares and looks like it forces it to shutdown/reboot and then generate a diag every time i will post one here. Wondering if i have miss configured something or its a bug. New ZFS pool main-storage 28 disks wtih 4 Vdevs using RIADz2 (moved to a full NVME/SAS SSD setup from HDDS) 2 Vdevs using 7 x 7.68TB NVME SSDs per dev 2 Vdevs using 7 x SAS 3.84TB SSDs per dev gilo2.0-diagnostics-20250117-0826.zip

So this issue is back again after a couple of reboots on 6.12.14.... will try to reapply the update files to my USB and see if it restores the main/dashboard pages.

Upgraded back to 6.12.14 and everything looks good still will be doing some data moving and swapping some disks out over next couple of weeks so a few reboots and see how it goes.

okay so I have now fixed the issue by reapplying the 6.12.13 original files to my USB drive from here https://docs.unraid.net/unraid-os/download_list/ kept my config folder intact and has booted up with both the main and dashboard pages working as expected. Still like to know what happened though, am also tempted to now reapply the 6.12.14 update and see if it still works.

safe mode has resolved the diagnostic issues worked instantly...... gilo2.0-diagnostics-20241204-1139.zip

not able to get diagnostics from the GUI just sits there doing nothing. rebooting into safe mode to see if I can get that to generate the diag. Also no Realtek drivers or plugins being used for connectivity. (Mellanox Connect x 5 dual 25Gb ports)

Hi all got a strange issue that has happened this week. Upgrade to 6.12.14 which had no issues. Replaced a faulty SSD in a BTRFS pool and booted up fine during rebuild second SSD failed but he GUI was working fine. Replace it again (intel DC SSDs) once booted back up the Main page and dashboard page are blank or showing no stats at all. I have tired edge, chrome and Firefox all the same tried 3 devices 2 PCs and my phone all the same also tried clearing the cache and an incognito window all same result. Booted into safe mode and was able to get the BTRFS pool sorted and the GUI was working fine as normal. BTRFS pool issues resolved but no GUI I then proceeded to downgrade back to 6.12.13. thinking it was a bug but its now booted back up and I have the same issue. no other changes have been made to the server. Diagnostics pulling down now taking its time. Am I missing something obvious here?

okay so i have added a static IP rebooted and now its working fine seems a bit odd to me especially since i didn't have this issue before upgrading to 6.12.8.

okay so reboot of router and server has made no difference at all this is odd as i have rebooted this server at least 4 times this morning with no issues at all when i had a DHCP reservation in place (now removed) before upgrading to 6.12.8 coming from 6.12.6. if i was to statically set an IP is this on the eth0 or br0?

yes so 2 x 1GB on board nics and eth0 is the one i want to use and is up. Odd as i have made no changes with the DHCP settings i did have a reservation in place for this but i removed it while fault finding. Ill give my google nest router a reboot see if that fixes it thanks ill come back and confirm.