Ram484

Can you telnet into your system and type "ipmi-sensors", then copy/paste the output here? root@Tower:~# ipmi-sensors ID | Name | Type | Reading | Units | Event 1 | Pwr Unit Status | Power Unit | N/A | N/A | 'OK' 2 | IPMI Watchdog | Watchdog 2 | N/A | N/A | 'OK' 3 | Physical Scrty | Physical Security | N/A | N/A | 'OK' 4 | SMI Timeout | OEM Reserved | N/A | N/A | 'OK' 5 | System Event Log | Event Logging Disabled | N/A | N/A | 'OK' 6 | System Event | System Event | N/A | N/A | 'OK' 7 | Button | Button/Switch | N/A | N/A | 'OK' 9 | VR Watchdog | Voltage | N/A | N/A | 'OK' 10 | SSB Therm Trip | Temperature | N/A | N/A | 'OK' 11 | BMC FW Health | Management Subsystem Health | N/A | N/A | 'OK' 12 | System Airflow | Other Units Based Sensor | 0.00 | CFM | 'OK' 14 | BB EDGE Temp | Temperature | 31.00 | C | 'OK' 15 | SSB Temp | Temperature | 47.00 | C | 'OK' 16 | BB BMC Temp | Temperature | 39.00 | C | 'OK' 17 | BB P2 VR Temp | Temperature | 31.00 | C | 'OK' 18 | BB MEM VR Temp | Temperature | 30.00 | C | 'OK' 19 | LAN NIC Temp | Temperature | 46.00 | C | 'OK' 20 | System Fan 4 | Fan | 1176.00 | RPM | 'OK' 21 | Processor 1 Fan | Fan | 1274.00 | RPM | 'OK' 22 | Processor 2 Fan | Fan | 1274.00 | RPM | 'OK' 23 | Rear Fan | Fan | 1078.00 | RPM | 'OK' 24 | P1 Status | Processor | N/A | N/A | 'Processor Presence detected' 25 | P2 Status | Processor | N/A | N/A | 'Processor Presence detected' 26 | P1 Therm Margin | Temperature | -60.00 | C | 'OK' 27 | P2 Therm Margin | Temperature | -58.00 | C | 'OK' 28 | P1 Therm Ctrl % | Temperature | 0.00 | % | 'OK' 29 | P2 Therm Ctrl % | Temperature | 0.00 | % | 'OK' 30 | P1 ERR2 | Processor | N/A | N/A | 'OK' 31 | P2 ERR2 | Processor | N/A | N/A | 'OK' 32 | CATERR | Processor | N/A | N/A | 'OK' 33 | P1 MSID Mismatch | Processor | N/A | N/A | 'OK' 34 | CPU Missing | Processor | N/A | N/A | 'OK' 35 | P1 DTS Therm Mgn | Temperature | -60.00 | C | 'OK' 36 | P2 DTS Therm Mgn | Temperature | -58.00 | C | 'OK' 37 | P2 MSID Mismatch | Processor | N/A | N/A | 'OK' 38 | P1 VRD Hot | Temperature | N/A | N/A | 'OK' 39 | P2 VRD Hot | Temperature | N/A | N/A | 'OK' 40 | P1 MEM01 VRD Hot | Temperature | N/A | N/A | 'OK' 41 | P1 MEM23 VRD Hot | Temperature | N/A | N/A | 'OK' 42 | P2 MEM01 VRD Hot | Temperature | N/A | N/A | 'OK' 43 | P2 MEM23 VRD Hot | Temperature | N/A | N/A | 'OK' 44 | DIMM Thrm Mrgn 1 | Temperature | -56.00 | C | 'OK' 45 | DIMM Thrm Mrgn 2 | Temperature | N/A | C | N/A 46 | DIMM Thrm Mrgn 3 | Temperature | -58.00 | C | 'OK' 47 | DIMM Thrm Mrgn 4 | Temperature | N/A | C | N/A 48 | Mem P1 Thrm Trip | Memory | N/A | N/A | 'OK' 49 | Mem P2 Thrm Trip | Memory | N/A | N/A | 'OK' 50 | BB +12.0V | Voltage | 11.78 | V | 'OK' 51 | BB +5.0V | Voltage | 4.92 | V | 'OK' 52 | BB +3.3V | Voltage | 3.34 | V | 'OK' 53 | BB +5.0V STBY | Voltage | 4.96 | V | 'OK' 54 | BB +3.3V AUX | Voltage | 3.28 | V | 'OK' 55 | BB +1.05V P1Vccp | Voltage | 0.81 | V | 'OK' 56 | BB +1.05V P2Vccp | Voltage | 0.77 | V | 'OK' 57 | BB +1.5 P1DDR AB | Voltage | N/A | V | N/A 58 | BB +1.5 P1DDR CD | Voltage | N/A | V | N/A 59 | BB +1.5 P2DDR AB | Voltage | N/A | V | N/A 60 | BB +1.5 P2DDR CD | Voltage | N/A | V | N/A 61 | BB +1.8V AUX | Voltage | 1.79 | V | 'OK' 62 | BB +1.1V STBY | Voltage | 1.08 | V | 'OK' 63 | BB VBAT | Voltage | 3.15 | V | 'OK' 64 | BB +1.35 P1LV AB | Voltage | 1.34 | V | 'OK' 65 | BB +1.35 P1LV CD | Voltage | 1.35 | V | 'OK' 66 | BB +1.35 P2LV AB | Voltage | 1.35 | V | 'OK' 67 | BB +1.35 P2LV CD | Voltage | 1.35 | V | 'OK' 71 | NM Capabilities | OEM Reserved | N/A | N/A | N/A 74 | P1 MTT | Memory | N/A | % | N/A 75 | P2 MTT | Memory | N/A | % | N/A root@Tower:~#

Working with local again I have one of the S2600CP2 systems and notice that the processor Therm Margin displays as negative (margin or headroom) but when selected as one of the four pull-downs it is displayed as ##. Could this be changed to display the same as the main Sensor display? Thanks for the quick update.

I just tried this IPMI plugin on SC2600CP board with the following results. I get the Event Log and can "remove all" but get "Unable to delete entry #: Invalid command" when deleting single. Sensors tab is not populated, just Done button. I get plenty of output from ipmitools -vc sdr. Pwr Unit Status,01h,ok,21.1, IPMI Watchdog,03h,ok,7.1, Physical Scrty,04h,ok,23.1, SMI Timeout,06h,ok,7.1, System Event Log,07h,ok,7.1, System Event,08h,ok,7.1, Button,09h,ok,7.1, VR Watchdog,0Bh,ok,7.1, SSB Therm Trip,0Dh,ok,7.1, BMC FW Health,10h,ok,7.1, System Airflow,0,CFM,ok,23.2,System Chassis,Other,180.000,0.000,360.000,,,,,,,0.000,510.000 BB EDGE Temp,27,degrees C,ok,7.1,System Board,Temperature,58.000,10.000,105.000,,115.000,110.000,,0.000,5.000,-128.000,127.000 SSB Temp,43,degrees C,ok,7.1,System Board,Temperature,52.000,10.000,93.000,,103.000,98.000,,0.000,5.000,-128.000,127.000 BB BMC Temp,42,degrees C,ok,7.1,System Board,Temperature,58.000,10.000,105.000,,115.000,110.000,,0.000,5.000,-128.000,127.000 BB P2 VR Temp,30,degrees C,ok,7.1,System Board,Temperature,58.000,10.000,105.000,,115.000,110.000,,0.000,5.000,-128.000,127.000 BB MEM VR Temp,34,degrees C,ok,7.1,System Board,Temperature,58.000,10.000,105.000,,115.000,110.000,,0.000,5.000,-128.000,127.000 LAN NIC Temp,52,degrees C,ok,7.1,System Board,Temperature,60.000,10.000,110.000,,120.000,115.000,,0.000,5.000,-128.000,127.000 System Fan 4,1176,RPM,ok,29.5,Fan Device,Fan,12740.000,490.000,24990.000,,,,,294.000,392.000,0.000,24990.000 Processor 1 Fan,1470,RPM,ok,29.8,Fan Device,Fan,12740.000,490.000,24990.000,,,,,294.000,392.000,0.000,24990.000 Processor 2 Fan,1372,RPM,ok,29.9,Fan Device,Fan,12740.000,490.000,24990.000,,,,,294.000,392.000,0.000,24990.000 P1 Status,70h,ok,3.1,Presence detected P2 Status,71h,ok,3.2,Presence detected P1 Therm Margin,-65,degrees C,ok,3.1,Processor,Temperature,-15.000,-70.000,0.000,,,,,,,-128.000,0.000 P2 Therm Margin,-62,degrees C,ok,3.2,Processor,Temperature,-15.000,-70.000,0.000,,,,,,,-128.000,0.000 P1 Therm Ctrl %,0,percent,ok,3.1,Processor,Temperature,0.000,0.000,20.000,,50.000,30.000,,,,0.000,100.000 P2 Therm Ctrl %,0,percent,ok,3.2,Processor,Temperature,0.000,0.000,20.000,,50.000,30.000,,,,0.000,100.000 P1 ERR2,7Ch,ok,7.1, P2 ERR2,7Dh,ok,7.1, CATERR,80h,ok,7.1, P1 MSID Mismatch,81h,ok,7.1, CPU Missing,82h,ok,7.1, P1 DTS Therm Mgn,-65,degrees C,ok,3.1,Processor,Temperature,-15.000,-70.000,0.000,,,,,,,-128.000,0.000 P2 DTS Therm Mgn,-62,degrees C,ok,3.2,Processor,Temperature,-15.000,-70.000,0.000,,,,,,,-128.000,0.000 P2 MSID Mismatch,87h,ok,7.1, P1 VRD Hot,90h,ok,3.1, P2 VRD Hot,91h,ok,3.2, P1 MEM01 VRD Hot,94h,ok,7.1, P1 MEM23 VRD Hot,95h,ok,7.1, P2 MEM01 VRD Hot,96h,ok,7.1, P2 MEM23 VRD Hot,97h,ok,7.1, DIMM Thrm Mrgn 1,-60,degrees C,ok,7.1,System Board,Temperature,-20.000,-70.000,0.000,,10.000,5.000,,,,-128.000,127.000 DIMM Thrm Mrgn 2,,,ns,7.1,System Board,Temperature,-20.000,-70.000,0.000,,10.000,5.000,,,,-128.000,127.000 DIMM Thrm Mrgn 3,-57,degrees C,ok,7.1,System Board,Temperature,-20.000,-70.000,0.000,,10.000,5.000,,,,-128.000,127.000 DIMM Thrm Mrgn 4,,,ns,7.1,System Board,Temperature,-20.000,-70.000,0.000,,10.000,5.000,,,,-128.000,127.000 Mem P1 Thrm Trip,C0h,ok,7.1, Mem P2 Thrm Trip,C1h,ok,7.1, BB +12.0V,11.831,Volts,ok,7.1,System Board,Voltage,11.935,11.363,12.559,,13.391,13.027,,10.635,10.947,0.287,13.547 BB +5.0V,4.915,Volts,ok,7.1,System Board,Voltage,4.981,4.742,5.241,,5.566,5.415,,4.460,4.590,0.098,5.631 BB +3.3V,3.339,Volts,ok,7.1,System Board,Voltage,3.282,3.125,3.454,,3.654,3.554,,2.953,3.039,0.050,3.697 BB +5.0V STBY,4.959,Volts,ok,7.1,System Board,Voltage,4.981,4.742,5.241,,5.566,5.415,,4.460,4.590,0.098,5.631 BB +3.3V AUX,3.282,Volts,ok,7.1,System Board,Voltage,3.282,3.125,3.454,,3.654,3.554,,2.953,3.039,0.050,3.697 BB +1.05V P1Vccp,0.810,Volts,ok,7.1,System Board,Voltage,1.056,0.582,1.428,,1.506,1.464,,0.546,0.564,-0.006,1.524 BB +1.05V P2Vccp,0.954,Volts,ok,7.1,System Board,Voltage,1.056,0.582,1.428,,1.506,1.464,,0.546,0.564,-0.006,1.524 BB +1.5 P1DDR AB,,,ns,7.1,System Board,Voltage,1.495,1.421,1.570,,1.659,1.611,,1.339,1.387,-0.055,1.679 BB +1.5 P1DDR CD,,,ns,7.1,System Board,Voltage,1.495,1.421,1.570,,1.659,1.611,,1.339,1.387,-0.055,1.679 BB +1.5 P2DDR AB,,,ns,7.1,System Board,Voltage,1.495,1.421,1.570,,1.659,1.611,,1.339,1.387,-0.055,1.679 BB +1.5 P2DDR CD,,,ns,7.1,System Board,Voltage,1.495,1.421,1.570,,1.659,1.611,,1.339,1.387,-0.055,1.679 BB +1.8V AUX,1.785,Volts,ok,7.1,System Board,Voltage,1.802,1.744,1.852,,1.960,1.902,,1.644,1.702,-0.132,1.985 BB +1.1V STBY,1.081,Volts,ok,7.1,System Board,Voltage,1.102,0.989,1.209,,1.276,1.240,,0.938,0.964,-0.012,1.291 BB VBAT,3.043,Volts,ok,7.1,System Board,Voltage,3.005,2.557,3.158,,,,,2.211,2.544,0.048,3.312 BB +1.35 P1LV AB,1.336,Volts,ok,7.1,System Board,Voltage,1.342,1.275,1.409,,1.488,1.445,,1.201,1.244,-0.049,1.506 BB +1.35 P1LV CD,1.354,Volts,ok,7.1,System Board,Voltage,1.342,1.275,1.409,,1.488,1.445,,1.201,1.244,-0.049,1.506 BB +1.35 P2LV AB,1.366,Volts,ok,7.1,System Board,Voltage,1.342,1.275,1.409,,1.488,1.445,,1.201,1.244,-0.049,1.506 BB +1.35 P2LV CD,1.348,Volts,ok,7.1,System Board,Voltage,1.342,1.275,1.409,,1.488,1.445,,1.201,1.244,-0.049,1.506 NM Capabilities,1Ah,ok,46.1, P1 MTT,0,percent,ok,3.1,Processor,Memory,,,,0.000,0.000,0.000,0.000,0.000,0.000,0.000,0.000 P2 MTT,0,percent,ok,3.2,Processor,Memory,,,,0.000,0.000,0.000,0.000,0.000,0.000,0.000,0.000 Can this board be supported?

I also have found the current disk upgrade procedure to be lacking in the "warm fuzzy" department. I support the: Lock Source drive Init Target drive (skip if pre cleared) Copy files from Source to Target (verify optional) Unmap Source drive - Map Target drive I understand that rebuild in place is required for failed and "no free port" conditions.